Skip to main content
SpringerLink
Log in

Optimization of heat-treatment parameters in hardening of titanium alloy Ti-6Al-4V by using the Taguchi method

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Titanium alloys are widely applied in aircraft, nuclear, and military parts because of their high strength-to-density ratio, high toughness, and high corrosion resistance. However, achieving excellent mechanical properties of these alloys relies on appropriate heat-treatment processes. In this research, the prevalent alloy Ti-6Al-4V was used to investigate the optimization process parameters of heat treatment by using the Taguchi method. Hardness after aging and tensile strength (TS) were chosen as quality characteristics. Eight controllable factors were selected, comprising fan, solution temperature, duration time of solution treatment, protective gas, quench delay time, cooling rate, temperature, and duration time of aging treatment. The experiment was performed using orthogonal arrays of L18(21 × 37). The best combination condition of process parameters was obtained after a Taguchi quality analysis. The quality reproducibility was verified to be excellent through confirmation experiments. The results showed that the hardness after aging was higher than HRC 43 ± 0.5, the TS of rod material higher than 169 ksi, and the TS of plate material higher than 157 ksi while using the best heat-treatment condition. The quality characteristics all met the AMS 4965 specifications of quality requirements for alloy Ti-6Al-4V.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Donachie MJ Jr (1982) Titanium and titanium alloys source book. ASM international, Metals Park, Ohio, OH, pp. 12–105

    Google Scholar 

  2. Donachie MJ Jr (1988) Titanium—a technical guide. ASM international, Metals Park, Ohio, OH, pp. 20–97

    Google Scholar 

  3. Collings EW (1989) The physical metallurgy of titanium alloys. ASM, Ohio, OH, pp. 1–130

    Google Scholar 

  4. ASM (1981) Heat treatment, metals handbook (Vol. 4), 9th edn. AMS Handbook Committee, Ohio, OH, pp. 763–774

    Google Scholar 

  5. Hwang JS (2004) Heat treatment of metal 18th edn. New Wen-Gin Development Issue, pp. 77–177

  6. AMS 2801B (2003) Heat treatment of titanium alloy parts. SAE Aerospace Material Specification

  7. AMS-H-81200 (2003) Heat treatment of titanium and titanium alloys. SAE Aerospace Material Specification

  8. Sue ZD (2006) Quality engineering. Quality Association of R.O.C. pp.7–111

  9. Lee HH (2000) Taguchi methods: principles and practices of quality design, 4th edn. Gaulih Book Co. Ltd, Taipei, pp. 19–68 181–217, 249–277

  10. Lin CC (2010) Applying the Taguchi method. Quality assurance education and training material. National Chung-Shan Institute of Science and Technology, Taoyuan

  11. Chang HN (1989) Introduction to Taguchi quality engineering. Chinese Society for Quality, Taipei, pp. 101–181

  12. Lin CC (1998) Improving the quality of heat treatment—the application of Taguchi quality engineering. Metal Heat Treatment 56:40–48

    Google Scholar 

  13. Chang CC, Yang JG, Chi L, Chou CP (2010) Optimization of heat-treatment parameters with the Taguchi method for the A7050 aluminum alloy. Adv Mat Res 139:157–162

    Article  Google Scholar 

  14. Palaniradja K, Alagumurthi N, Soundararajan V (2005) Optimization of process variables in gas carburizing process—a Taguchi study with experimental investigation on SAE 8620 and AISI 3310 steels. Turkish J Eng Env Sci 29:279–284

    Google Scholar 

  15. Mason PW, Prevey PS (2001) Iterative Taguchi analysis—optimizing the austenite content and hardness in 52100 steel. J Mater Eng Perform 10(1):14–21

    Article  Google Scholar 

  16. AMS 4965J (2007) Titanium alloy, 6.0Al-4.0V, solution heat treated and aged, SAE Specification

  17. Onzawa T, Suzumura A, Ko MW (1988) Brazing of titanium using low-melting-point Ti-based filler metals. 19th International AWS Brazing and Soldering Conference, New Orleans, LA

Download references

Author information

Authors and Affiliations

  1. Mechanical Engineering Department, National Taiwan University, Taiwan, Republic of China

    Kuo-Hsun Lee & Sen-Yeu Yang

  2. National Chung-Shan Institute of Science and Technology, Taiwan, Republic of China

    Ji-Gang Yang

Authors
  1. Kuo-Hsun Lee
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Sen-Yeu Yang
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Ji-Gang Yang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Kuo-Hsun Lee.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Lee, KH., Yang, SY. & Yang, JG. Optimization of heat-treatment parameters in hardening of titanium alloy Ti-6Al-4V by using the Taguchi method. Int J Adv Manuf Technol 90, 753–761 (2017). https://doi.org/10.1007/s00170-016-9433-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-016-9433-3

Keywords

Search

Navigation