Skip to main content
SpringerLink
Log in

Modified male die rapid gas blow forming of fine-grained Mg alloy AZ31B thin sheet

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Gas blow forming of a commercial, fine-grained, 0.6-mm-thick Mg alloy AZ31B thin sheets under high strain rates to decrease the forming time was investigated in the present work. An innovative male die rapid gas blow forming method was developed. Using this new method and stepwise pressurization profiles, alloy sheets were successfully deformed to form shallow rectangular pans. Deformation characteristics of rapid gas blow forming were discussed. Results indicated that the proposed process significantly reduces the forming time and that a shallow rectangular pan may be formed under a maximum average strain rate of approximately 10−2 s−1. A 10-mm-high rectangular pan was formed in <109 s. Sheet thinning was improved by modified male die forming. The fillet radius of the rectangular pan was found to be one of the key factors that influence the rapid gas blow forming time. Strain-enhanced grain growth was the major growth mechanism during rapid gas blow forming. Grain growth and cavitation were not serious problems during rapid gas blow forming.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Cusick M, Abu-Farha F, Lours P, Maoult Y, Bernhart G, Khraisheh M (2012) Superplastic forming of AZ31 magnesium alloy with controlled microstructure. Mat-Wiss Werkst 43:810–816

    Article  Google Scholar 

  2. Khraisheh MK, Abu-Farha FK, Weinmann KJ (2007) Investigation of post-superplastic forming properties of AZ31 magnesium alloy. Ann CIRP 56:289–292

    Article  Google Scholar 

  3. Sorgente D, Scintilla LD, Palumbo G, Tricarico L (2010) Blow forming of AZ31 magnesium alloy at elevated temperatures. Int J Mater Form 3:13–19

    Article  Google Scholar 

  4. Yin DL, Zhang KF, Wang GF, Han WB (2005) Superplasticity and cavitation in AZ31 Mg alloy at elevated temperatures. Mater Lett 59:1714–1718

    Article  Google Scholar 

  5. Franchitti S, Giuliano G, Palumbo G, Sorgente D, Tricarico L (2008) On the optimisation of superplastic free forming test of an AZ31 magnesium alloy sheet. Int J Mater Form 1(Suppl):1067–1070

    Article  Google Scholar 

  6. Tan JC, Tan MJ (2002) Superplasticity in a rolled Mg–3Al–1Zn alloy by two-stage deformation method. Scr Mater 47:101–106

    Article  Google Scholar 

  7. Watanabe H, Fukusumi M (2008) Mechanical properties and texture of a superplastically deformed AZ31 magnesium alloy. Mater Sci Eng A 477:153–161

    Article  Google Scholar 

  8. Krajewski PE, Schroth JG (2007) Overview of quick plastic forming technology. Mater Sci Forum 551–552:3–12

    Article  Google Scholar 

  9. Schroth JG, Brueggeman HM, Grewal NP (2007) Quick plastically formed aluminum doors: design and performance. J Mater Eng Perform 16:339–348

    Article  Google Scholar 

  10. Chung SW, Higashi K, Kim WJ (2004) Superplastic gas pressure forming of fine grained AZ61 magnesium alloy sheet. Mater Sci Eng A 372:15–20

    Article  Google Scholar 

  11. Kim WJ, Park JD, Yoon US (2008) Superplasticity and superplastic forming of Mg–Al–Zn alloy sheets fabricated by strip casting method. J Alloy Compd 464:197–204

    Article  Google Scholar 

  12. Blandin JJ (2007) Superplastic forming of magnesium alloys: production of microstructures, superplastic properties, cavitation behavior. Mater Sci Forum 551–552:211–217

    Article  Google Scholar 

  13. Panicker R, Chokshi AH, Mishra RK, Verma R, Krajewski PE (2009) Microstructural evolution and grain boundary sliding in a superplastic magnesium AZ31 alloy. Acta Mater 57:3683–3693

    Article  Google Scholar 

  14. Qiao J, Wang Y, Shi GD (2010) High temperature tensile behavior of extruded and rolled AZ31 Mg alloy. Trans Nonferrous Metals Soc China 20:s540–s544

    Article  Google Scholar 

  15. Watanabe H, Tsutsui H, Mukai Y, Kohzu M, Tanabe S, Higashi K (2001) Deformation mechanism in a coarse-grained Mg–Al–Zn alloy at elevated temperatures. Int J Plast 17:387–397

    Article  Google Scholar 

  16. Chung SW, Watanabe H, Kim WJ, Higashi K (2004) Creep deformation mechanisms in coarse-grained solid solution Mg alloys. Mater Trans 45:1266–1271

    Article  Google Scholar 

  17. Liu J, Tan MJ, Aue-u-lan Y, Jarfors AEW, Fong KS, Castagne S (2011) Superplastic-like forming of non-superplastic AA5083 combined with mechanical pre-forming. Int J Adv Manuf Technol 52:123–129

    Article  Google Scholar 

  18. Liu J, Tan MJ, Lim CVS, Chua BW (2013) Process optimization and microstructural development during superplasticlike forming of AA5083. Int J Adv Manuf Technol 69:2415–2422

    Article  Google Scholar 

  19. Liu J, Tan MJ, Aue-u-lan Y, Guo ML, Castagne S, Chua BW (2013) Superplastic-like forming of Ti–6Al–4V alloy. Int J Adv Manuf Technol 69:1097–1104

    Article  Google Scholar 

  20. Tang JS, Fuh YK, Lee S (2015) Superplastic forming process applied to aero-industrial strakelet: wrinkling, thickness, and microstructure analysis. Int J Adv Manuf Technol 77:1513–1523

    Article  Google Scholar 

  21. Del Valle JA, Perez-Prado MT, Ruano OA (2005) Deformation mechanisms responsible for the high ductility in a Mg AZ31 alloy analyzed by electron backscattered diffraction. Metall Mater Trans A 36:1427–1438

    Article  Google Scholar 

  22. Yoshinaga H, Horiuchi R (1963) On the nonbasal slip in magnesium crystals. Trans JIM 5:14–21

    Google Scholar 

  23. Koike J, Kobayashi T, Mukai T, Watanabe H, Suzuki M, Maruyama K, Higashi K (2003) The activity of non-basal slip systems and dynamic recovery at room temperature in fine-grained AZ31B magnesium alloys. Acta Mater 51:2055–2065

    Article  Google Scholar 

  24. Wu HY, Lee S, Wang JY (2002) Effect of inverted pressurization profile on deformation characteristics of 5083 aluminium alloy during superplastic forming. Mater Sci Technol 18:438–444

    Article  Google Scholar 

  25. Sun PH, Wu HY, Tsai HH, Huang CC, Tzou MD (2010) Effect of pressurization profile on the deformation characteristics of fine-grained AZ31B Mg alloy sheet during gas blow forming. J Mater Process Technol 210:1673–1679

    Article  Google Scholar 

  26. Wu HY, Sun PH, Zhu FJ, Liu HC, Chiu CH (2012) Tensile properties and shallow pan rapid gas blow forming of commercial fine-grained Mg alloy AZ31B thin sheet. Procedia Eng 36:329–334

    Article  Google Scholar 

  27. Wu HY, Perng JY, Shis SH, Chiu CH, Lee S, Wang JY (2006) Cavitation characteristics of a superplastic 5083 Al alloy during gas blow forming. J Mater Sci 41:7446–7453

    Article  Google Scholar 

  28. Clark MA, Alden TH (1973) Deformation enhanced grain growth in a superplastic Sn–1% Bi alloy. Acta Metall 21:1195–1206

    Article  Google Scholar 

  29. Ghosh AK, Hamilton CH (1979) Mechanical behavior and hardening characteristics of a superplastic Ti–6Al–4V alloy. Metall Trans A 10:699–706

    Article  Google Scholar 

  30. Hamilton CH, Ash BA, Sherwood D, Heikkinen HC (1988) Effect of microstructural dynamics on superplasticity in Al alloys. In: Heikkinen HC, McNelley TR (eds) Superplasticity in aerospace. The Meallurgical Society, Inc., Warrendal, pp 29–50

    Google Scholar 

  31. Carpenter JA, Jackman J, Li N, Osborne RJ, Powell BR, Sklad P (2007) Automotive Mg research and development in North America. Mater Sci Forum 546–549:11–24

    Article  Google Scholar 

  32. Weiler JP, Wood JT (2009) Modeling fracture properties in a die-cast AM60B magnesium alloy I—analytical failure model. Mater Sci Eng A 527:25–31

    Article  Google Scholar 

  33. Weiler JP, Wood JT (2012) Modeling the tensile failure of cast magnesium alloys. J Alloy Compd 537:133–140

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Chung Hua University, 707, Sec.2, WuFu Rd., Hsinchu, 30012, Taiwan

    Horng-Yu Wu, Ming-Da Tzou, Chih-Chao Huang & Hsin-Han Tsai

Authors
  1. Horng-Yu Wu
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Ming-Da Tzou
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Chih-Chao Huang
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Hsin-Han Tsai
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Horng-Yu Wu.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Wu, HY., Tzou, MD., Huang, CC. et al. Modified male die rapid gas blow forming of fine-grained Mg alloy AZ31B thin sheet. Int J Adv Manuf Technol 80, 1241–1252 (2015). https://doi.org/10.1007/s00170-015-7121-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-015-7121-3

Keywords

Search

Navigation