Abstract
Genetically optimized neural network systems (GONNS) was developed to simulate the intelligent decision-making capability of human beings. After they are trained with experimental data or observations, GONNS use one or more artificial neural networks (ANN) to represent complex systems. The optimization is performed by one or more genetic algorithms (GA). In this study, the GONNS was used to estimate the optimal operating condition of the friction stir welding (FSW) process. Five separate ANNs represented the relationship between two identical input parameters and each one of the considered characteristics of the welding zone. GA searched for the optimized parameters to make one of the parameters maximum or minimum, while the other four are kept within the desired range. The GONNS was found as an excellent optimization tool for FSW.
Article PDF
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Avoid common mistakes on your manuscript.
References
Sato YS, Sugiura Y, Shoji Y, Park SHC, Kokawa H, Ikeda K (2004) Post-weld formability of friction stir welded Al alloy 5052. Mater Sci Eng A 369:138–143
Mandal S, Williamson K (2006) A thermomechanical hot channel approach for friction stir welding. J Mater Process Technol 174:190–194
Paglia CS, Jata KV, Buchheit RG (2006) A cast 7050 friction stir weld with scandium: microstructure, corrosion and environmental assisted cracking. Mater Sci Eng A 424:196–204
Okuyucu H, Kurt A, Arcaklioglu E (2007) Artificial neural network application to the friction stir welding of aluminum plates. Mater Des 28:178–184
Zhoua C, Yang X, Luan G (2006) Investigation of microstructures and fatigue properties of friction stir welded Al–Mg alloy. Mater Chem Phys 98:285–290
Kulekci MK, Şik A, Kaluç E (2008) Effects of tool rotation and pin diameter on fatigue properties of friction stir welded lap joints. Int J Adv Manuf Technol 36:877–882
Chen C, Kovacevic R, Jandgric D (2003) Wavelet transform analysis of acoustic emission in monitoring friction stir welding of 6061 aluminum applied to friction stir welded steel. Int J Mach Tools Manuf 43:1383–1390
Prado RA, Murr LE, Soto KF, McClure JC (2003) Self-optimization in tool wears for friction-stir welding of Al 6061_/20% Al2O3 MMC. Mater Sci Eng A 349:156–165
Fernandez GJ, Murr LE (2004) Characterization of tool wear and weld optimization in the friction-stir welding of cast aluminum 359 + 20% SiC metal-matrix composite. Mater Charact 52:65–75
Buffa G, Hua J, Shivpuri R, Fratini L (2006) Design of the friction stir welding tool using the continuum based FEM model. Mater Sci Eng A 419:381–388
Zhang Z, Zhang HW (2007) Material behaviors and mechanical features in friction stir welding process. Int J Adv Manuf Technol 35:86–100
Zhou C, Yang X, Luan G (2006) Effect of root flaws on the fatigue property of friction stir welds in 2024–T3 aluminum alloys. Mater Sci Eng A 418:155–160
Ouyang J, Yarrapareddy E, Kovacevic R (2006) Microstructural evolution in the friction stir welded 6061 aluminum alloy (T6-temper condition) to copper. J Mater Process Technol 172:110–122
Heurtier P, Jones MJ, Desrayaud C, Driver JH, Montheillet F, Allehaux D (2006) Mechanical and thermal modelling of friction stir welding. J Mater Process Technol 171:348–357
Czechowski M (2005) Low-cycle fatigue of friction stir welded Al–Mg alloys. J Mater Process Technol 164–165:1001–1006
Sato YS, Nelson TW, Sterling CJ, Pettersson CO (2005) Microstructure and mechanical properties of friction stir welded SAF 2507 super duplex stainless steel. Mater Sci Eng A 397:376–384
Jones MJ, Heurtier P, Desrayaud C, Montheillet F, Allehaux D, Driver JH (2005) Correlation between microstructure and microhardness in a friction stir welded 2024 aluminium alloy. Scripta Mater 52:693–697
Chen CM, Kovacevic R (2004) Joining of Al 6061 alloy to AISI 1018 steel by combined effects of fusion and solid state welding. Int J Mach Tools Manuf 44:1205–1214
Liu HJ, Fujii H, Maeda M, Nogi K (2003) Tensile properties and fracture locations of friction-stir-welded joints of 2017–T351 aluminum alloy. J Mater Process Technol 142:692–696
Rumelhart DE, Hilton G, Williams RJ (1986) Learning internal representations by error propagation. In: Rumelhart E, McClelland JL (eds) Parallel distributed processing: explorations in the microstructure of cognition, vol 1. MIT Press, Cambridge, MA
Dayhoff JE (1990) Neural network architectures: an introduction. Van Nostrand Reinhold Co., New York, NY
Hecht-Nielsen R (1990) Neurocomputing. Addison-Wesley Publishing Company, Massachusetts, USA
DARPA (1988) Neural network study. AFCEA International Press, Fairfax
Chryssolouris G, Domroese M, Beaulieu P (1992) Sensor synthesis for control of manufacturing processes. J Eng Ind Trans ASME 114:158–174
Tansel IN (1990) Neural network approach for representation and simulation of 3D-cutting dynamics. Trans North Am Met Res Inst, 18:193–200
Tansel I, Bao WY, Arkan TT, Tansel B (1997) Visualization of underground contamination by using neural networks, smart engineering system design: neural networks, fuzzy logic, and evolutionary programming. ASME Press, New York
Masters T (1995) Advanced algorithms for neural networks. Wiley, New York
Goldberg DE (1989) Genetic algorithms in search. Optimization and machine learning. Addison-Wesley, Reading, MA
Carroll DL (1996) Chemical laser modeling with genetic algorithms. AIAA J 34:338–346
Winter G, Cuesta P, Periaux J et al (1996) Genetic algorithm in engineering and computer science. Wiley, New York
Tansel IN, Ozcelik B, Bao WY, Chen P, Rincon D, Yang SY, Yenilmez A (2006) Selection of optimal cutting conditions by using GONNS. Int J Mach Tools Manuf 46:26–35
Tansel IN, Yang SY, Shu C, Bao WY, Mahendrakar N (1999) Introduction to genetically optimized neural network systems (GONNS). Smart engineering systems: neural networks, fuzzy logic, evolutionary programming, data mining, and rough sets. ASME Press, New York, pp 331–336
Yang SY, Tansel IN, Kropas-Hughes CV (2003) Selection of optimal material and operating conditions in composite manufacturing part I: computational tool. Int J Mach Tools Manuf 43:169–173
Yang SY, Girivasan V, Singh NR, Tansel IN, Kropas-Hughes CV (2003) Selection of optimal material and operating conditions in composite manufacturing. Part II: complexity representation of characteristics and decision making. Int J Mach Tools Manuf 43:175–184
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This is an open access article distributed under the terms of the Creative Commons Attribution Noncommercial License (https://creativecommons.org/licenses/by-nc/2.0), which permits any noncommercial use, distribution, and reproduction in any medium, provided the original author(s) and source are credited.
About this article
Cite this article
Tansel, I.N., Demetgul, M., Okuyucu, H. et al. Optimizations of friction stir welding of aluminum alloy by using genetically optimized neural network. Int J Adv Manuf Technol 48, 95–101 (2010). https://doi.org/10.1007/s00170-009-2266-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-009-2266-6