Abstract
This study aims to propose a novel method, vacuum infusion process, to measure the longitudinal permeability of wood. The vacuum infusion method uses a vacuum bag sealed over the fibrous material, with a vacuum inlet and a vacuum outlet. It can be performed on top of any flat surface, and its process is relatively swift. Six different woods (Pinus elliottii, Araucaria angustifolia, Ochroma pyramidale, Cedrela fissilis, Tectona grandis, and Eucalyptus grandis) and three different fluids (water, soybean oil, and furfuryl alcohol) were selected for the study. After preliminary evaluations of morphology, chemical characteristics, density, porosity, contact angle and capillary pressure, three woods and two fluids were selected for the actual permeability measurements. The highest permeability was obtained for the Ochroma pyramidale wood, being 0.45–7.49 × 10–11 m2. This wood was 58–88% and 18–62% more permeable than the Pinus elliottii and Eucalyptus grandis woods, respectively. The fluid was found to have some influence on the experiment and therefore must be carefully selected. The difference in permeability of the woods was attributed to morphological characteristics, especially the presence of axial vessels, which are 60% larger for Ochroma pyramidale wood compared to Eucalyptus grandis wood, while Pinus elliottii has no vessels. The amount of voids in all woods, nevertheless, was similar, as well as the evaluated chemical characteristics and structural anatomical elements (tracheids and/or fibers). In all, the determination of apparent permeability using the vacuum infusion process is practical and with good accuracy, yielding results similar to those from other methods in the literature.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Acosta A, Avila R, De, Campos S, Alberto D (2021a) Fast-growing pine wood modified by a two-step treatment based on heating and in situ polymerization of polystyrene. Constr Build Mater 302:124422. https://doi.org/10.1016/j.conbuildmat.2021.124422
Acosta AP, Barbosa KT, Amico SC et al (2021b) Improvement in mechanical, physical and biological properties of eucalyptus and pine woods by raw pine resin in situ polymerization. Ind Crops Prod 166:113495. https://doi.org/10.1016/j.indcrop.2021.113495
Ahmed SA, Chun SK (2009) Observation of liquid permeability related to anatomical characteristics in Samanea saman. Turk J Agric For 33:155–163. https://doi.org/10.3906/tar-0807-13
Ahmed SA, Chun SK (2011) Permeability of Tectona grandis L. As affected by wood structure. Wood Sci Technol 45:487–500. https://doi.org/10.1007/s00226-010-0335-5
Ai W, Duval H, Pierre F, Perré P (2017) A novel device to measure gaseous permeability over a wide range of pressures: characterisation of slip flow for Norway spruce, European beech, and wood-based materials. Holzforschung 71:147–162. https://doi.org/10.1515/hf-2015-0264 (hal-01523306)
Aitomäki Y, Moreno-Rodriguez S, Lundström TS, Oksman K (2016) Vacuum infusion of cellulose nanofibre network composites: influence of porosity on permeability and impregnation. Mater Des 95:204–211. https://doi.org/10.1016/j.matdes.2016.01.060
Alms JB, Garnier L, Glancey JL, Advani SG (2010) In-plane permeability characterization of the vacuum infusion processes with fiber relaxation. Int J Mater Form 3:1267–1275. https://doi.org/10.1007/s12289-010-0690-7
Amico SC, Lekakou C (2002) Axial impregnation of a fiber bundle. Part 1: capillary experiments. Polym Compos 23:249–263. https://doi.org/10.1002/pc.10429
Amorim MRS, Ribeiro PG, Martins SA et al (2013) Surface wettability and roughness of 11 amazonian tropical hardwoods. Floresta e Ambient 20:99–109. https://doi.org/10.4322/floram.2012.069
Bajpai P (2018) Wood and fiber—growth and anatomy. Biermann’s Handb Pulp Pap 75–103. https://doi.org/10.1016/b978-0-12-814240-0.00003-3
Barnett JR (2004) Encyclopedia of Forest Sciences. Elsevier Inc 1st edn. ISBN: 9780080548012
Booker RE (1990) Changes in transverse wood permeability during the drying of Dacrydium cupressinum and Pinus radiata. NZ J For Sci 20:231–244
Borrega M, Ahvenainen P, Serimaa R, Gibson L (2015) Composition and structure of balsa (Ochroma pyramidale) wood. Wood Sci Technol 49:403–420. https://doi.org/10.1007/s00226-015-0700-5
Brändström J (2001) Micro- and ultrastructural aspects of norway spruce tracheids: A review. IAWA J 22:333–353. https://doi.org/10.1163/22941932-90000381
Brito AS, Vidaurre GB, Tarcísio J et al (2019) Effect of planting spacing in production and permeability of heartwood and sapwood of Eucalyptus wood. Floresta e ambiente 26:1–9. https://doi.org/10.1590/2179-8087.037818
Bufalino L, Mendes LM, Tonoli GHD et al (2013) Relation of transverse air permeability with physical properties in different compositions of sugarcane bagasse particleboards. Mater Res 16:150–157. https://doi.org/10.1590/S1516-14392012005000164
Caglar B, Salvatori D, Sozer EM, Michaud V (2018) In-plane permeability distribution mapping of isotropic mats using flow front detection. Compos Part A Appl Sci Manuf 113:275–286. https://doi.org/10.1016/j.compositesa.2018.07.036
da Silva AAX, Souza JA, Manes A, Amico SC (2020) In-plane permeability and mechanical properties of R-glass/aramid hybrid composites. J Mater Eng Perform 29:4484–4492. https://doi.org/10.1007/s11665-020-04944-1
Emaminasab M, Tarmian A, Pourtahmasi K (2015) Permeability of poplar normal wood and tension wood bioincised by Physisporinus vitreus and Xylaria longipes. Int Biodeterior Biodegrad 105:178–184. https://doi.org/10.1016/j.ibiod.2015.09.003
Esmailpour A, Taghiyari HR, Golchin M, Avramidis S (2019) On the fluid permeability of heat treated paulownia wood. Int Wood Prod J 10:55–63. https://doi.org/10.1080/20426445.2019.1617954
Esteves B, Marques AV, Domingos I, Pereira H (2013) Chemical changes of heat treated pine and eucalypt wood monitored by ftir. Maderas Cienc y Tecnol 15:245–258. https://doi.org/10.4067/S0718-221X2013005000020
Gartner BL, Meinzer FC (2005) Relationships in sapwood water transport and storage. U.S. Departament of Agriculture. In: Vascular transport in plants 307–331. https://www.fs.usda.gov/treesearch/pubs/25525
Hansmann C, Gindl W, Wimmer R, Teischinger A (2002) Permeability of wood - A review. Drev Vysk Res 47:1–16
Kishino M, Nakano T (2004) Artificial weathering of tropical woods. Part 2: Color change. Holzforschung 58:558–565. https://doi.org/10.1515/HF.2004.085
Leggate W, Kumar C, Mcgavin RL, Faircloth A (2021) The effects of drying method on the wood permeability, wettability, treatability, and gluability of southern pine from Australia. BioRes 16:698–720. https://ojs.cnr.ncsu.edu/index.php/BioRes/article/view/BioRes_16_1_698_Leggate_Drying_Method_Wood_Permeability
Leggate W, Redman A, Wood J et al (2019) Radial permeability of the hybrid pine (Pinus elliottii × Pinus caribaea) in Australia. BioResources 14:4358–4372. https://doi.org/10.15376/biores.14.2.4358-4372
Lehringer C, Richter K, Schwarze FWMR, Militz H (2009) A review on promising approaches for liquid permeability improvement in softwoods. Wood Fiber Sci 41:373–385
Lengowski EC, Júnior EAB, Nisgoski S et al (2020) Properties of thermally modified teakwood. Maderas Cienc Tecnol 23:1–16. https://doi.org/10.4067/S0718-221X2021000100410
Li Y, Xie L, Ma H (2015) Permeability and mechanical properties of plant fiber reinforced hybrid composites. Mater Des 86:313–320. https://doi.org/10.1016/j.matdes.2015.06.164
Mahdian M, Huang LY, Kirk DW, Jia CQ (2020) Water permeability of monolithic wood biocarbon. Microporous Mesoporous Mater 303:110258. https://doi.org/10.1016/j.micromeso.2020.110258
Oberhofnerová E, Pánek M (2016) Surface wetting of selected wood species by water during initial stages of weathering. Wood Res 61:545–552
Piao C, Winandy JE, Shupe TF (2010) From hydrophilicity to hydrophobicity: a critical review: part I. Wettability and surface behavior. Wood Fiber Sci 42:490–510
Rezende RN, Lima JT, Elís L et al (2018) Wood Permeability in Eucalyptus grandis and Eucalyptus dunnii. Floresta e ambiente 25:1–7. https://doi.org/10.1590/2179-8087.022815
Rogério M, Oliveira G, De, Deiner J et al (2010) Permeability measurements of Brazilian eucalyptus. Mater Res 13:281–286. https://doi.org/10.1590/S1516-14392010000300002
Rossi D, Rossi S, Morin H, Bettero A (2012) Within-tree variations in the surface free energy of wood assessed by contact angle analysis. Wood Sci Technol 46:287–298. https://doi.org/10.1007/s00226-011-0407-1
Rudd C, Kendall KN, Mangin C (1993) Resin transfer moulding, structural reaction injection moulding and related processing techniques. Scand J Clin Lab Invest 52:14. https://doi.org/10.1080/00365519309107736
Severiano LC, Lahr FAR, Bardi MAG et al (2010) Influence of gamma radiation on properties of common Brazilian wood species used in artwork. Prog Nucl Energy 52:730–734. https://doi.org/10.1016/j.pnucene.2010.04.008
Siau (1984) Transport processes in wood, vol 5. Springer, Heidelberg, p 2000
Summerscales J, Searle TJ (2005) Low-pressure (vacuum infusion) techniques for moulding large composite structures. Proc Inst Mech Eng Part L J Mater Des Appl 219:45–58. https://doi.org/10.1243/146442005X10238
Taghiyari HR, Habibzade S, Miri Tari SM (2014) Effects of wood drying schedules on fluid flow in Paulownia wood. Dry Technol 32:89–95. https://doi.org/10.1080/07373937.2013.813855
Tappi T 211 om-02 (2002) Ash in wood, pulp, paper and paperboard: combustion at 525°C. In: TAPPI TEST METHODS. Technical Association of Pulp an Paper Industry. Atlanta, GA. Tappi Press. pp 1–5
Tappi (2007) Preparation of wood for chemical analysis (Revision of T 264 cm-97). T264 C 1988:3–5
Tappi T222 Om-02 (2011) Lignin in wood and pulp. In: TAPPI TEST METHODS. Technical Association of Pulp an Paper Industry. Atlanta, GA. Tappi Press. pp 1–7
Tappi T 204 cm-97 (2012) Solvent extractives of wood and pulp T 204 cm-97. TAPPI TEST METHODS Tech Assoc Pulp an Pap Ind Atlanta. GA Tappi Press, pp 1–12
Tappi T257 (2012) Sampling and preparing wood for chemical analysis. In: TAPPI TEST METHODS. Technical Association of Pulp an Paper Industry. Atlanta, GA. Tappi Press
Tarmian A, Zahedi Tajrishi I, Oladi R, Efhamisisi D (2020) Treatability of wood for pressure treatment processes: a literature review. Eur J Wood Prod 78:635–660. https://doi.org/10.1007/s00107-020-01541-w
Trevisan R, Zanella A, da Silva FM, Rosa M, Fioresi T, Fortes FDO (2016) Axial variation of basic density of Araucaria angustifolia wood in different diameter classes. For Sci 46:1969–1972
Trindade RS, Ribeiro AC, Souza JA, Amico SC (2019) Experimental investigation of transverse permeability applied to liquid molding. Polym Compos 40:3938–3946. https://doi.org/10.1002/pc.25254
Valério A, Watzlawick LF, Silvestre R, Koehler HS (2008) Determinação da densidade básica da madeira de cedro (Cedrela fi ssilis Vell.) ao longo do fuste. (Determination of the basic density of cedar wood (Cedrela fi ssilis Vell .) along the stem). Appl Res Agrotechnol 1
Yun M, Carella T, Simacek P, Advani S (2017) Stochastic modeling of through the thickness permeability variation in a fabric and its effect on void formation during Vacuum Assisted Resin Transfer Molding. Compos Sci Technol 149:100–107. https://doi.org/10.1016/j.compscitech.2017.06.016
Zabel RA, Morrell JJ (2020) Chemical protection of wood (wood preservation). Wood Microbiology (Second Edition). Elsevier Inc 471-515. https://doi.org/10.1016/B978-0-12-819465-2.00019-X
Zhang Y, Cai L (2008) Impact of heating speed on permeability of sub-alpine fir. Wood Sci Technol 42:241–250. https://doi.org/10.1007/s00226-007-0172-3
Acknowledgements
This work was supported by Coordination for the Improvement of Higher Education—CAPES (code 001) and National Council for Scientific and Technological Development—CNPq (Financial code 301758/2019-0).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Acosta, A.P., Barbosa, K.T., da Silva, A.A.X. et al. Vacuum infusion as a novel method to determine wood permeability. Eur. J. Wood Prod. 81, 33–44 (2023). https://doi.org/10.1007/s00107-022-01887-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00107-022-01887-3