Abstract
The preferred orientation and earing characteristics of 2S aluminum were studied. An empirical correlation was obtained relating earing behavior and variation of mechanical properties for face-centered cubic metals. Strain-ratio measurements for 2S were found to be in good agreement with Hill’s theory of plastic anisotropy.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
J. D. Jevons: The Metallurgy of Deep Drawing and Pressing (1942) p. 89. Chapman & Hall.
M. Whitaker: The Deep Drawing of Non-Ferrous Metals. Sheet Metal Industries (1950) 27, No. 281, p. 815.
M. Cook and T. LL. Richards: The Structural Changes Effected in 70:30 Brass Strip by Cold Rolling and Annealing. Journal Inst. Metals (1943) 69, p. 351.
M. Cook and T. LL. Richards: Directional Characteristics of Single-Texture-Structure Copper Strip. Journal Inst. Metals (1943) 69, p. 201.
W. M. Baldwin, Jr., T. S. Howald, and A. W. Ross: Relative Triaxial Deformation Rates. Trans. AIME (1946) 166, p. 86; Metals Technology (September 1945).
L. Bourne and R. Hill: On the Correlation of the Directional Properties of Rolled Sheet in Tension and Cupping Tests. Philosophical Magazine (1950) 41, p. 671.
R. Hill: A Theory of the Yielding and Plastic Flow of Anisotropic Metals. Proc. Royal Soc. (1948) 193A, p. 281.
H. Hu, P. R. Sperry, and P. A. Beck: Rolling Textures in Face-Centered Cubic Metals. Trans. AIME (1952) 194, p. 76; Journal of Metals (January 1952).
P. A. Beck and H. Hu: Annealing Textures in Rolled Face-Centered Cubic Metals. Trans. AIME (1952) 194, p. 83; Journal of Metals (January 1952).
D. W. Smith: Symposium of Radiography and X-ray Diffraction. (1937) ASTM Philadelphia.
E. W. Palmers and C. S. Smith: Effect of Some Mill Variables on the Earing of Brass in Deep Drawing. Trans. AIME (1942) 147, p. 164.
W. H. Bassett and J. C. Bradley: Ears on Cupro-Nickel Cups. Trans. AIME (1933) 104, p. 181.
F. H. Wilson and R. M. Brick: Textures, Anisotropy, and Earing Behavior of Brass. Trans. AIME (1945) 161, p. 173.
M. Cook and T. LL. Richards: The Influence of Crystal Structure on the Cold Rolling and Annealing of Copper Strip. Journal Inst. Metals (1941) 67, p. 203.
A. Hone and E. C. Pearson: Grain Orientation in Aluminum Revealed by Anodic Film. Metal Progress (1948) 53, p. 363; also Metal Progress (1950) p. 713.
P. Lacombe and L. Beaujard: Etude Microscopique de l’ecrouissage et de la recrystallisation de l’aluminium extra-pur. Revue Metallurgie (1947) 44, p. 71.
W. M. Baldwin, Jr.: Effect of Rolling and Annealing upon the Crystallography, Metallography, and Physical Properties of Copper Strip. Trans. AIME (1946) 166, p. 591. I
T. LL. Richards: Preferred Orientation in Non-Ferrous Metals. Progress in Metal Physics (1949) Vol. 1. London. B. Chalmers.
Author information
Authors and Affiliations
Additional information
Discussion on this paper, TP 3475E, may be sent, 2 copies, to AIME by May 1, 1953. Manuscript, Sept. 9, 1952. Los Angeles Meeting, February 1953.
Rights and permissions
About this article
Cite this article
Aust, K.T., Morral, F.R. Directional Properties of 2S Aluminum. JOM 5, 431–436 (1953). https://doi.org/10.1007/BF03398967
Published:
Issue Date:
DOI: https://doi.org/10.1007/BF03398967