Abstract
This work presents the three-dimensional analysis of flow and heat transfer performed for a wire-wrapped fuel assembly of liquid metal reactor using Reynolds-averaged Navier-Stokes analysis in conjunction with SST model as a turbulence closure. The whole fuel assembly has been analyzed for one period of the wire-spacer using periodic boundary conditions at inlet and outlet of the calculation domain. Three different assemblies, two 7-pin wire-spacer fuel assemblies and one bare rod bundle, apart from the pressure drop calculations for a 19-pin case, have been analyzed. Individual as well as a comparative analysis of the flow field and heat transfer have been discussed. Also, discussed is the position of hot spots observed in the wire-spacer fuel assembly. The flow field in the subchannels of a bare rod bundle and a wire-spacer fuel assembly is found to be different. A directional temperature gradient is found to exist in the subchannels of a wire-spacer fuel assembly. Local Nusselt number in the subchannels of wirespacer fuel assemblies is found to vary according to the wire-wrap position while in case of bare rod bundle, it’s found to be constant.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
CFX-5.7 Solver Theory,2004, Ansys Inc.
Cheng, S. K. and Todreas, N. E., 1986, “Hydrodynamic Models and Correlations for Bare and Wire-Wrapped Hexagonal rod Bundles-Bundle Friction Factors, Subchannel Friction Factors and Mixing Parameters,”Nuclear Engineering and Design, Vol. 92, pp. 227–251.
Choi, S. K., Choi, K., Nam, H. Y., Choi, J. H. and Choi, H. K., 2003, “Measurement of Pressure Drop in a Full-Scale Fuel Assembly of a Liquid Metal Reactor,”Journal of Pressure Vessel Technology, Vol. 125.
Chun, M. H. and K. W. Seo, 2001, “An Experimental Study and Assessment of Existing Friction Factor Correlations for Wire-Wrapped Fuel Assemblies,” Annals of Nuclear Energy, Vol. 28, pp. 1683–1695.
Coffield, R. D. and Markley, R. A., 1980, “Natural Convection Analysis and Verification for LMFBR Cores,”Nuclear Engineering and Design, Vol. 62, pp. 181–198.
Cui, X. Z. and Kim, K. Y., 2003, “Three Dimensional Analysis of Turbulent Heat Transfer and Flow Through Mixing Vane in a Subchannel of Nuclear Reactor,”Journal of Nuclear Science and Techonology, Vol. 40, No. 10, pp. 719–724.
Engel, F. C., Minushkin, B., Atkins, R. J. and Markley, R. A., 1980, “Characterization of Heat Transfer and Temperature Distribution in an Electrically Heated Model of an LMFBR Blanket Assembly,”Nuclear Engineering and Design, Vol. 62, pp. 335–347.
Fontana, M. H., 1973, “Temperature Distribution in the Duct Wall and at the Exit of a 19-Rod Simulated LMFBR Fuel Assembly (FFM-2A),” ORNL-4852, Oak Ridge National Laboratory.
Ha, K. S., Jeong, H. Y., Chang, W. P., Kwon, Y. M. and Lee, Y. B., 2004, “Wire-Wrap Models for Subchannel Blockage Analysis,”Journal of the Korean Nuclear Society, Vol. 36, pp. 165–174.
Han, G. Y., 2000, “A Mathematical Model for the Thermal-Hydraulic Analysis of Nuclear Power Plants,”Int. Comm. Heat Mass Transfer, Vol. 27, pp. 795–805.
Incropera, F. P. and DeWitt, D. P., 2002,Heat and Mass Transfer (Fifth Edition), John Wiley and Sons, Inc., p. 493
Khan, E. U., Rohsenw, W. M., Sonin, A. A. and Todreas, N. E., 1975, “A Porous Body Model for Predicting Temperature Distribution in Wire-Wrapped Fuel Rod Assemblies,”Nuclear Engineering and Design, Vol. 35, pp. 1–12.
Khan, E. U., Rohsenw, W. M., Sonin, A. A. and Todreas, N. E., 1975, “A Porous Body Model for Predicting Temperature Distribution in Wire-Wrapped Fuel Rod Assemblies Operating in Combined Forced and Free Convection,”Nuclear Engineering and Design, Vol. 35, pp. 199–211.
Kim, H. M. and Kim, K. Y., 2004, “Design Optimization of Rib-Roughened Channel to Enhance Turbulent Heat Transfer,”International Journal of Heat and Mass Transfer, Vol. 47, pp. 5159–5168.
Kim, K. Y. and Seo, J. W., 2005, “Numerical Optimization for The Design of A Spacer Grid with Mixing Vane in A Pressurized Water Reactor Fuel Assembly,”Nuclear Technology, Vol. 149, pp. 62–70.
Kim, W. S. et at., 2002, “A Subchannels Analysis Code MATRA-LMR for Wire Wrapped LMR Subassembly,”Annals of Nuclear Energy, Vol. 29, 3003-321-2002.
Macdougall, J. D. and Lillington, J. N., 1984, “The SABRE Code for Fuel Rod Cluster Thermohydraulics,”Nuclear Engineering and Design, Vol. 82, pp. 91–407.
Madni, I. K. and Agarwal, A. K., “LMFBR System Analysis: Impact of Heat Transport System on Core Thermal-Hydraulics,”Nuclear Engineering and Design, Vol. 62, pp. 199–218.
Menter, F. and Esch, T., 2001, “Elements of Industrial Heat Transfer Predictions,”16th Bazilian Congress of Mechanical Engineering (CPBEM), Uberlandia, Brazil.
Patankar, S.V., 1980,Numrical Heat Transfer and Fluid Flow, Hemisphere, Washington DC.
Rehme, K. and Trippe, G., 1980, “Pressure Drop and Velocity Distribution in Rod Bundles with Spacer Grids,”Nuclear Engineering and Design, Vol. 62, pp. 349–359.
Roidt, R. M., Carelli, M. D. and Markley, R. A., 1980, “Experimental Investigations of the Hydraulic Field in Wire-Wrapped LMFBR core Assemblies,”Nuclear Engineering and Design, Vol. 62, pp. 295–321.
Sha, W. T., 1980, “An overview on Rod-Bundle Thermal-Hydraulic Analysis,”Nuclear Engineering and Design, Vol. 62, pp. 1–24.
Takase, K., 1995, “Experimental and Analytical Studies on Turbulent heat Transfer Performance of a Fuel Rod with Spacer Ribs for High Temperature Gas-Cooled Reactors,”Nuclear Engineering and Design, Vol. 154, pp. 345–356.
Yang, W. S., 1997, “An LMR Core Thermal-Hydraulics Code Based on the ENERGY Model,”J. of Korean Nuclear Society, Vol. 29, p. 406.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Ahmad, I., Kim, KY. Flow and convective heat transfer analysis using RANS for a wire-wrapped fuel assembly. J Mech Sci Technol 20, 1514–1524 (2006). https://doi.org/10.1007/BF02915974
Received:
Revised:
Issue Date:
DOI: https://doi.org/10.1007/BF02915974