Abstract
This article describes the construction and properties of a new type of guarded hot plate apparatus for the investigation of thermal insulations. The article begins with a general discussion of some of the characteristics of the conventional unit, noting especially the long time required to reach steady state conditions and the accuracy given in round-robin-tests. Errors when measuring in a onesided guarded hot plate are discussed and calculated. A description is given of the constructed guarded hot plate and its characteristics. It is shown that it is possible to reach steady state in very moderate periods of time combined with stable and accurate measurements.
Similar content being viewed by others
References
ASTM, 1968a.—Standard method of test for thermal conductivity of materials by means of the guarded hot plate, ASTM, C 177-63. (1968 Book of ASTM Standards, part 14), pp. 17–28. Philadelphia, Pa.
B.S., 1965.—Methods of determining thermal properties, B.S. 874: 1965. (British Standards Institution.), London.
DIN, 1959.—Bestimmung der Wärmeleitfähigkeit mit dem Plattengerät, DIN 52 612. (Deutsche Normenausschuss.), Berlin.
Poensgen R..—Ein technisches Verfahren zur Ermittlung der Wärmeleitfähigkeit plattenförmiger Stoffe, Zeitschrift des VDI, Nr. 41, Band 56, 1912, pp. 1653–1658.
Robinson H., Watson W..—Interlaboratory comparison of thermal conductivity determinations with guarded hot plates, ASTM, STP 119, 1951, pp. 36–44.
RILEM.—Détermination du coefficient de conductivité thermique par la méthode de la plaque chaude. Bulletin RILEM, No. 18, 1963, pp. 41–72, Paris.
Gasquet R..—Méthodes de mesure de la conductivité. Revue Générale de Thermique, No. 23, 1963, pp. 1245–1258.
I.I.R..—International comparative measurements of thermal conductivity. International Institute of Refrigeration, Paris, 1968.
Fournier D., Klarsfeld S..—Mesures de conductivité thermique des matériaux isolants par un appareil orientable à plaque chaude bi-gardée. International Institute of Refrigeration, 1969, pp. 321–332.
Brendeng E., Frivik P.-E..—On the design of a guarded hot plate apparatus. International Institute of Refrigeration, 1969, pp. 281–288, 317–319.
ASTM.—Guarded hot plate apparatus complying with the requirements of section 4 of ASTM standard method of test for thermal conductivity of materials by means of the guarded hot plate. ASTM, C 177-45. Philadelphia, Pa.
Gilbo C.F..—Experiments with a guarded hot plate thermal conductivity set. ASTM, STP 119, 1951, pp. 45–57.
Pascal A..—La mesure de la conductivité thermique des matériaux du bâtiment, Annales de l'Institut Technique du Bâtiment et des Travaux Publics. No. 90, 1955, pp. 583–598.
Zabawsky Z..—An improved guarded hot plate thermal conductivity apparatus with automatic controls. ASTM, STP 217, 1957, pp. 3–17.
Fischer F..—Die Problematik von Wärmeleitfähighkeitsmessungen an Schaumstoffen. Kunststoffe, Heft 5, Band 56, 1966, pp. 321–327.
Karp G.S., Lankton C.S..—A guarded-hot-plate thermal conductivity apparatus for multilayer cryogenic insulation. ASTM, STP 411, 1967, pp. 13–24.
Fritz W., Küster W..—Beitrag zur Kenntnis der Wärmeleitfähigkeit poröser Stoffe. Wärme- und Stoffübertragung, Bd. 3, 1970, pp. 155–168.
Bashford L., Ferguson J..—Instrumentation and temperature control of guarded hot-plate system for measuring thermal properties of seed cotton. Transactions of the ASAE, 1970, pp. 155–157.
Ferro V., Sacchi A..—An automatic plate apparatus for measurements of thermal conductivity of insulating materials at high temperatures. Proc. of the eighth conf., Thermal Conductivity, 1969, pp. 737–760.
Woodside W..—Deviations from one-dimensional heat flow in guarded hot-plate measurements. Review Scientific Instruments, Vol. 28, No. 12, 1957, pp. 1033–1037.
Donaldson I.G..—A theory for the square guarded hot plate—a solution of the heat conduction equation for a two layer system. Quarterly of Appl. Mathematics, Vol. XIX, No. 3, 1961, pp. 205–219.
Donaldson I.G..—Computed errors for a square guarded hot plate for the measurement of thermal conductivities of insulating materials. Brit. J. Appl. Phys., Vol. 13, 1962, pp. 598–602.
Woodside W., Wilson A.G..—Unbalance errors in guarded hot plate measurements. ASTM, STP 217, 1957, pp. 32–48.
Somers E., Cyphers J..—Analysis of errors in measuring thermal conductivity of insulating materials. Review Scientific Instruments, Vol. 22, No. 8, 1951, pp. 583–586.
Dusinberre G.M..—Further analysis of errors of the guarded hot plate, Review Scientific Instruments, Vol. 23, No. 11, 1952, pp. 649.
Woodside W..—Analysis of errors due to edge heat loss in guarded hot plates. ASTM, STP 217, 1957, pp. 49–64.
Bankvall C..—Heat transfer in fibrous materials. National Swedish Institute for Building Research, Document D4, 1972.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Bankvall, C. Guarded hot plate apparatus for the investigation of thermal insulations. Mat. Constr. 6, 39–47 (1973). https://doi.org/10.1007/BF02474841
Issue Date:
DOI: https://doi.org/10.1007/BF02474841