Abstract
The problem of the equilibrium shape and departure size of two-dimensional dropwise condensation drops on a vertical surface, presented in an earlier work, is extended to include advancing contact angles to 180°. The equation of the surface of the drop is obtained by minimizing (for a given volume) the total energy of the drop, consisting of surface and gravitational energy, using the techniques of variational calculus. The solution is tractable once the advancing contact angle is known, and is taken as an approximation to the axial meridian profile of a threedimensional drop. The receding contact angle is obtained as part of the solution.
The drop size is specified by imposing its vertical length in contact with the wall. A maximum value of this length exists which provides a real solution, and this is taken as the departure size of the drop. It is shown that the general departure shape for an advancing contact angle of 180° includes the cases for all advancing contact angles.
Zusammenfassung
Das bereits in einer früheren Arbeit behandelte Problem der Gleichgewichtsform und der Abreißgröße eines Kondensationstropfens an einer senkrechten Fläche wird hiermit auf Vorrückwinkel bis zu 180 ° erweitert. Die Gleichung für die Tropfenoberfläche wird dabei durch Minimierung der Gesamtenergie des Tropfens (bei gegebenem Volumen), die ihrerseits die Oberflächen und die Gravitationsenergie enthält, mit Hilfe der Variationsrechnung bestimmt. Dabei erfordert die Lösung für den zweidimensionalen Tropfen lediglich die Kenntnis des Vorrückwinkels. Sie kann dann als Näherung für den axialen Meridian-Schnitt eines dreidimensionalen Tropfens verwendet werden. Dabei ergibt sich der Rückzugswinkel des Tropfens als ein Teil der Lösung.
Die Tropfengröße ist bestimmt durch die vertikale Kontaktlänge an der Wand. Einen Maximalwert dieser Länge erhält man aus der Forderung, daß die Lösung noch reell bleibt. Die derart ermittelte Länge wird als maßgebliche Abreißgröße des Tropfens angesehen. Schließlich wird gezeigt, daß die allgemeine Abreißform bei einem Vorrückwinkel von 180° auch alle Fälle anderer Vorrückwinkel enthält.
Similar content being viewed by others
Abbreviations
- a :
-
acceleration
- A :
-
drop cross section area
- C :
-
integration constants - Equations (17)
- E :
-
elliptic integral of second kind
- F :
-
elliptic integral of first kind
- f :
-
functional
- g :
-
acceleration due to gravity
- K :
-
functions defined by Equations (17)
- L :
-
drop length
- P, Q :
-
parameters of elliptic integrals
- U :
-
energy
- V :
-
volume
- x, y :
-
coordinates
- η, β :
-
integration variables
- λ :
-
Lagrange multiplier
- θ :
-
contact angle
- Φ, γ :
-
amplitudes of elliptic integrals
- σ :
-
surface tension
- ϱ :
-
density difference between liquid and vapor
- A :
-
advancing
- d :
-
departure
- l :
-
liquid
- M :
-
maximum
- O :
-
shifted origin
- r :
-
relative coordinate
- R :
-
receding
- s :
-
solid
- v :
-
vapor
- *:
-
imensionless new functional
References
Merte, H., jr.; Yamali, C: Profile and departure size of con- densation drops on vertical surfaces. Wärme-Stoffübertrag. 17 (1983) 171–180
Fox, C.: An introduction to the calculus of variations. Oxford University Press 1950
Gradshteyn, I. S.; Ryzhik, I.: Table of integrals, series and products. New York: Academic Press 1965
Author information
Authors and Affiliations
Additional information
Dedicated to Prof. Dr.-Ing. U. Grigull's 75th birthday
Rights and permissions
About this article
Cite this article
Merte, H., Son, S. Further considerations of two-dimensional condensation drop profiles and departure sizes. Wärme- und Stoffübertragung 21, 163–168 (1987). https://doi.org/10.1007/BF01377573
Received:
Issue Date:
DOI: https://doi.org/10.1007/BF01377573