Skip to main content

Continuous-flow hydrogenation over resin supported palladium catalyst for the synthesis of industrially relevant chemicals

Abstract

Herein, the catalytic performance of palladium nanoparticles grafted on the polymeric TSNH2 (Tentagel-S-NH2) resin was investigated for continuous-flow liquid-phase hydrogenation of two industrially relevant chemicals: 2-methyl-3-butyn-2-ol and nitrocyclohexane. We investigated the effect of process parameters such as temperature and pressure on PdTSNH2 activity and selectivity. Depending on the reaction conditions, well-dispersed PdNPs with average size of about 2 nm have shown very high flexibility in terms selectivity toward the desired products: 2-methyl-3-buten-2-ol or 2-methyl-2-butanol in the case of 2-methyl-3-butyn-2-ol hydrogenation and cyclohexanone oxime or cyclohexylamine as the main product in the case of nitrocyclohexane conversion. The optimal reaction conditions for 2-methyl-3-buten-2-ol formation were estimated at 25 °C and 5 bar, and in the case of cyclohexanone oxime formation at 40 °C and 10 bar. We demonstrated the general trend in the catalytic performance of 2.2 wt% Pd grafted on Tentagel-S-NH2. Independently of the hydrogenated substrate, the increase in conversion leads to decreased selectivity to 2-methyl-3-buten-2-ol and cyclohexanone oxime at the expense of increasing the selectivity to 2-methyl-2-butanol or cyclohexylamine.

Graphic abstract

Introduction

Hydrogenation, and especially catalytic hydrogenation, is one of the most important transformations in the chemical industry. Catalytic hydrogenations are carried out with homogeneous and heterogeneous catalysts using molecular hydrogen or its donors like isopropanol or formic acid [1,2,3].

Sustainable development requires modern, more intense, more efficient, and environmentally friendly technologies, and implementation of continuous-flow methods also belongs to this trend [4,5,6,7,8,9,10]. Therefore, in our studies, we implemented the liquid-phase continuous–flow hydrogenation of two of the crucial chemicals that have been studied minimally or have not been investigated at all in flow conditions: 2-methyl-3-butyn-2-ol (MBY) and nitrocyclohexane (NC).

The partial catalytic hydrogenation of 2-methyl-3-butyn-2-ol is an in-depth studied process, mainly because the C≡C bond partial hydrogenation product (2-methyl-3-buten-2-ol) is an essential intermediate for the industrial synthesis of vitamins (A, E), as well as a variety of perfumes [11]. The current manufacturing process is based on the Lindlar or other Pd-based heterogeneous catalysts under batch conditions. Although the desired product yields are in the range of 95–97%, very fast catalyst deactivation is observed [12]. Continuous–flow hydrogenation of 2-methyl-3-butyn-2-ol has been carried out only with Pd/TiO2, Pd-TS (3D printed Catalytic Static Mixers), bimetallic PdZn/TiO2, and Lindlar catalyst [13,14,15]. The best results in terms of "alkene" yield were reported for a capillary microreactor with a bimetallic Pd25Zn75 catalyst supported on mesoporous TiO2 (89%) and for 5 wt% Pd-TS (100%). The second desired product of 2-methyl-3-butyn-2-ol hydrogenation is 2-methyl-2-butanol—widely used as solvent in synthetic flavouring, pharmaceuticals, corrosion inhibitors, and making plastics and other chemicals [16]. However, 2-methyl-2-butanol is obtained by hydration of 2-methyl-2-butene in the presence of an acidic catalyst [17]. Therefore, getting a semi-saturated product (2-methyl-3-butene-2-ol) seems to be a more desired process.

On the other hand, we selected nitrocyclohexane because it is an excellent source of many useful chemicals. Additionally, until now, liquid-phase nitrocyclohexane hydrogenation has been conducted only in batch conditions, at elevated pressure and temperature [18, 19]. According to our knowledge, there is only one article related to the hydrogenation of nitrocyclohexane, but under gas flow conditions [20]. Therefore, our experiments of the continuous-flow nitrocyclohexane hydrogenation in liquid phase open new perspectives in producing industrially relevant chemicals like e.g., cyclohexanone oxime (an essential component in polyamide manufacturing) or cyclohexylamine with its substantial role as a building block for pharmaceuticals.

Careful analysis of literature data displays the dominant role of noble metals, especially Pd, as catalysts in heterogeneous hydrogenation. Nonetheless, very high hydrogenolytic ability makes palladium less selective towards specific products such as semi-hydrogenation of C≡C to C=C, like in the case of hydrogenation of 2-methyl-3-butyn-2-ol or partial hydrogenation of nitrocyclohexane towards cyclohexanone oxime.

Therefore, to improve product-specificity, palladium catalysts are modified in different ways. One of the popular methods is based on the differences in metal nanoparticles' interaction with varying types of support (MSI) [21]. The interaction between the metal species and the support (MSI) could significantly affect the electronic structure and geometric configuration of metal species. The strength and type of MSI depend both on the size of the metallic species and the properties of the support [21]. For example, in the case of metal supported on oxides, the direct bond of a metal with cation (metal sites) or anion (oxygen sites) can be taken as the bridge to realize the metal-support interaction. Therefore, except the intrinsic electronic and geometric structures of metal species, surface properties of oxides as the supports determine the interaction between metal and oxides, which correspondingly influences the catalytic behaviours of metal species. On the other hand, it is challenging to induce strong MSI in the case of the carbon-supported materials, especially by depositing metal species on perfect carbon support [22]. Only the engineering defects or introduction of additional anchoring sites, and dangling bonds of edge carbon sites enable to build MSI and efficiently tune the catalytic behaviours of metal species. In consequence, the MSI plays a critical role in tuning the catalytic activity, selectivity and stability (e.g. resistance from sintering at a high temperature) of metal species on different supports [21, 23].

Therefore, our study aimed to investigate the catalytic performance of Pd grafted on a polymeric resin (TS-NH2) in hydrogenation of two different substrates important in chemical technology. To the best of our knowledge, such studies have not yet been reported. Our results have shown that the combination of 2.2 wt% Pd with polymeric resin shows high efficiency for the synthesis of industrially relevant chemicals (2-methyl-3-buten-2-ol, 2-methyl-2-butanol in the case of 2-methyl-3-butyn-2-ol conversion and cyclohexanone oxime or cyclohexylamine in the case of nitrocyclohexane conversion).

Experimental

Catalyst synthesis and physicochemical characterization

Tentagel-S-NH2 (Rapp Polymere GmbH) in beads form with a diameter of 130 µm and capacity of 0.2–0.35 mmol/g was used as the support for Pd nanoparticles. 2.2 wt% PdTS-NH2 was synthesized under ambient conditions at room temperature, using a two-step method. Initially, palladium (II) acetylacetone was mixed with sodium borohydride as a reducing agent. Palladium nanoparticles formed, which was indicated by a colour change from orange-yellow to black. In the second step, Pd nanoparticles were immobilized onto polymeric resin with amino groups by adding a portion of Tentagel-S-NH2 to nanoparticle solution and vigorous stirring (1000 rpm) for 24 h at room temperature. During this step, polymeric resin was able to capture all palladium nanoparticles from the solution. After filtration, Pd catalyst was dried overnight at 120 °C.

Elemental analysis was performed using atomic absorption spectrometry (AAS) and inductively coupled plasma—optical emission spectrometry (ICP-OES).

X-ray photoelectron spectroscopy (XPS) spectra were recorded with a PHI 5000 VersaProbe™(ULVAC-PHI) scanning ESCA Microprobe using monochromatic Al-Kαradiation (hν = 1486.6 eV) from an X-ray source operating at 100 μm spot size, 25 W power and 15 kV acceleration voltage. High resolution (HR) XPS spectra were collected with a hemispherical analyser at the pass energy of 23.5 eV. The energy step size was 0.1 eV and the photoelectron take-off angle was 45° with respect to the surface. CasaXPS software was used to evaluate the XPS data. Deconvolution of XPS spectra was performed using a Shirley background and a Gaussian peak shape. The binding energies (BE) for all detected spectra were calibrated with respect to the BE of carbon sp3 C 1s at 285 eV [24].

STEM and TEM experiments were performed on the electron microscope Titan G2 60–300 kV (FEI, Japan) equipped with EDAX EDS (energy-dispersive X-ray spectroscopy) detector. Microscopic studies of the catalysts were performed at an accelerating voltage of the electron beam equal to 300 kV. The sample was prepared by dispersion in pure alcohol using an ultrasonic cleaner; a drop of this suspension was placed on carbon films on copper grids.

Catalytic tests

The liquid-phase catalytic hydrogenation was performed using ThalesNano H-Cube Pro continuous-flow micro-reactor with an HPLC pump. Substrate (2-methyl-3-butyn-2-ol or nitrocyclohexane) solution in ethanol was flown through CatCart®70 cartridge with 0.1 g of a palladium catalyst. The hydrogen was generated in situ via water electrolysis. Both reactions were carried out with longer and shorter residence time (defined as bed volume/reactant flow rate) ranged within limits 0.4–2.70 min, to optimise the most favourable reaction conditions. Finally, catalytic hydrogenation of 2-methyl-3-butyn-2-ol was conducted with PdTSNH2 over a wide range of temperatures (10–100 °C) and pressures (1–20 bar) with reactant flow rate 1.5 ml/min and H2 flow rate 60 ml/min. Catalytic hydrogenation of nitrocyclohexane was also conducted with PdTSNH2 over a wide range of temperatures (25–100 °C), but in the pressure range from 1 to 10 bar and flow rate of 0.3 ml/min and H2 flow rate 60 ml/min. It is worth mentioning that during the reactions with TSNH2, there were no products of 2-methyl-3-butyn-2-ol or nitrocyclohexane hydrogenation. That excludes catalytic activity of the polymeric resin. Substrate conversion and product formation were analysed by gas chromatography (GC) Bruker 456 GC equipped with FID detector and BP 1 60 × 0.25 × 0.25 column.

Results and discussion

Elemental analysis estimated by atomic absorption spectrometry (AAS) and inductively coupled plasma—optical emission spectrometry (ICP-OES) showed that Pd loading in PdTSNH2 is 2.2 wt%.

The X-ray photoelectron spectroscopy measurement was carried out to determine the oxidation state of palladium nanoparticles. XPS results of the Pd 3d region for PdTSNH2 are presented in Table 1. The dominant signals of Pd 3d5/2 located at 334.38 eV and 335.56 eV relate to Pd in metallic form [25, 26]. The shift with respect to the reported bulk position [27] and small asymmetry of the peak (results not shown) can be an evidence of a metallic species' presence in the nanoparticulated form [19]. The metallic palladium is also accompanied by oxide states (PdO and PdO2). The total atomic concentration of Pd on the surface was estimated at 1.54%.

Table 1 Binding energies of the Pd 3d 5/2 and Pd 3d 3/2 peaks of the as-prepared PdTSNH2 catalyst

Moreover, SEM and TEM investigations confirmed that palladium NPs are well dispersed on the surface with a narrow particle size range. An average metal particle size was estimated as ~ 2 nm (Fig. 1).

Fig. 1
figure1

STEM, TEM results, and palladium particle size distribution for as-prepared palladium nanoparticles grafted on the polymeric TSNH2 (Tentagel-S-NH2) resin (Pd loading 2.2 wt%)

PdTSNH2 catalytic performance was investigated in the continuous-flow hydrogenation of 2-methyl-3-butyn-2-ol (MBY) and nitrocyclohexane (NC) (Figs. 2 and 3). Hydrogenation of 2-methyl-3-butyn-2-ol over a wide range of temperatures and pressures showed that both temperature and pressure seem to affect 2-methyl-3-buten-2-ol selectivity. Significantly, higher pressures led to significant changes in product selectivity (Fig. 2). Independent on the temperature, 2-methyl-2-butanol was formed as a major product of MBY hydrogenation at 1 bar and 3 bar, while higher pressures promote formation of the more desired product (unsaturated alcohol). Moreover, the optimum temperature was found in the lower range. According to these tests, palladium grafted on Tentagel-S-NH2 showed 100% of selectivity toward the saturated alcohol over a rather wide range of temperatures and pressures. On the other hand, obtaining high selectivity to the partially hydrogenated product was possible only at specific reaction conditions. In respect to selectivity toward 2-methyl-3-butene-2-ol, the optimum values were specified to be 25 °C and 5 bar, yielding PdTSNH2 activity of ca. 67 µmol/min with 93% of the selectivity to the unsaturated alcohol. Additionally, the palladium catalyst maintained the reported performance for the entire time on stream (ca. 300 min).

Fig. 2
figure2

Effect of reaction conditions on the activity and selectivity of 2.2 wt% PdTSNH2 in 2-metyl-3-butyn-2-ol hydrogenation towards 2-methyl-3-buten-2-ol and 2-methyl-2-butanol with 1.5 ml/min flow rate of the reactant

Fig. 3
figure3

Effect of reaction conditions on the activity and selectivity of 2.2 wt% PdTSNH2 in nitrocyclohexane hydrogenation towards cyclohexylamine and cyclohexanone oxime with 0.3 ml/min flow rate of the reactant

The direct comparison of our results with literature data is not trivial due to different reaction conditions (e.g., residence time, substrate concentration, H2/substrate ratio) and different palladium loading, in comparison to earlier studies [9, 15]. Although our results may seem slightly worse or comparable to the industrial standard catalysts such as Lindlar's and Pd-Nanoselect catalysts [15], the general trend with respect of the selectivity toward unsaturated product was the same as in the work of Kundra et al. [15]. Increasing both temperature and pressure was found to benefit 2-methyl-3-butyn-2-ol conversion at the selectivity's cost toward the unsaturated product. Additionally, our measurements showed that the pressure increase seems to minimally affect the substrate activity over the temperature range of 10–45 °C, but results in a decrease in selectivity to 2-methyl-3-buten-2-ol at the expense of an increase in selectivity to 2-methyl-2-butanol (Table 2). Moreover, independently of the hydrogen pressure, increase in the temperature up to 65 °C did not affect the very high activity (100% of 2-methyl-3-butyn-2-ol conversion) but strongly decreased the selectivity towards unsaturated product e.g. 61% of selectivity for 5 bar and 65 °C and only 7% at 85 °C at the same pressure (Table 2). As a result of our research, we have also determined the optimal pressure and temperature conditions (5 bar, 25 °C) for the production of 2-methyl-3-buten-2-ol, the key intermediate in the synthetic method of vitamin A and E production.

Table 2 2-methyl-3-butyn-2-ol hydrogenation results for liquid flow rate-1.5 ml/min, H2 flow rate-60 ml/min, residence time-0.5 min

Continuous–flow hydrogenation of nitrocyclohexane (NC) on PdTSNH2 led to formation of cyclohexylamine and cyclohexanone oxime. Fig. 3 shows the influence of the reaction conditions on the selectivity towards the two desired products. The selectivity to cyclohexanone oxime did not depend as much on pressure as it depended on the reaction temperature (Fig. 3, Table 3). Generally, under higher pressures, higher temperature is needed to obtain 100% selectivity to cyclohexanone oxime. It is 25 °C at 5 bar and 40 °C at 10 bar. Every time, increase in temperature led to increased activity at a given pressure, accompanied by an increased selectivity towards the second desired product—cyclohexylamine. However, comparison of the catalyst activity at 1, 2, 5, and 10 bar indicates higher PdTSNH2 activity at lower temperature and pressure. Maximum activity and maximum selectivity to cyclohexylamine (96%) are obtained for 2 bar and 100 °C (Table 3).

Table 3 Nitrocyclohexane hydrogenation results for liquid flow rate-0.3 ml/min, H2 flow rate-60 ml/min, residence time-2.7 min

It should be mentioned here that this is the first reported continuous-flow nitrocyclohexane hydrogenation in liquid-phase, according to our knowledge. Only hydrogenations at batch conditions were successfully conducted with noble metals as catalysts [18, 19, 28] with cyclohexylamine or oxime cyclohexanone formation. Therefore, we are sure that our results are promising from this point of view and open a new perspective in the efficient nitrocyclohexane conversion.

Conclusions

Our results clearly show that PdTSNH2 is an effective catalyst in hydrogenation processes to synthetise industrially relevant chemicals (2-methyl-3-buten-2-ol and cyclohexanone oxime). High activity and ~ 100% of the selectivity towards desired products of 2-methyl-3-butyn-2-ol or nitrocyclohexane hydrogenation strongly depend on the reaction conditions and the presence of very small (~ 2 nm) palladium nanoparticles grafted on the Tentagel-S-NH2 resin. The optimal reaction conditions for 2-methyl-3-buten-2-ol formation were estimated at 25 °C and 5 bar and in the case of cyclohexanone oxime formation at 40 °C and 10 bar. We also demonstrated the general trend in the catalytic performance of 2.2 wt% Pd grafted on Tentagel-S-NH2. Independently of the hydrogenated substrate, the increase in conversion leads to decreased selectivity to 2-methyl-3-buten-2-ol and cyclohexanone oxime, at the expense of increasing the selectivity to 2-methyl-2-butanol or cyclohexylamine.

Data availability

The authors declare that all data supporting the findings of this study are available within the article.

References

  1. 1.

    Zanotti-Gerosa A, Angelini T, Roseblade S (2020) Efficient and selective solvent-free homogeneous hydrogenation of aldehydes under mild reaction conditions using [RuCl2(dppb)(ampy)]. Tetrahedron Lett 61:151677. https://doi.org/10.1016/j.tetlet.2020.151677

    CAS  Article  Google Scholar 

  2. 2.

    Wang D, Deraedt C, Ruiz J, Astruc D (2015) Sodium hydroxide-catalyzed transfer hydrogenation of carbonyl compounds and nitroarenes using ethanol or isopropanol as both solvent and hydrogen donor. J Mol Catal A 400:14–21. https://doi.org/10.1016/j.molcata.2015.01.024

    CAS  Article  Google Scholar 

  3. 3.

    Wang T, Du J, Sun Y et al (2020) Catalytic transfer hydrogenation of biomass-derived furfural to furfuryl alcohol with formic acid as hydrogen donor over CuCs-MCM catalyst. Chin Chem Lett. https://doi.org/10.1016/j.cclet.2020.07.044

    Article  Google Scholar 

  4. 4.

    Giziński D, Błachucki W, Śrębowata A et al (2018) On-the-fly catalyst accretion and screening in chemoselective flow hydrogenation. ChemCatChem 10:3641–3646. https://doi.org/10.1002/cctc.201800581

    CAS  Article  Google Scholar 

  5. 5.

    Ley SV, Stewart-Liddon AJP, Pears D et al (2006) Hydrogenation of aromatic ketones, aldehydes, and epoxides with hydrogen and Pd(0)EnCatTM 30NP. Beilstein J Org Chem 2:2–6. https://doi.org/10.1186/1860-5397-2-15

    CAS  Article  Google Scholar 

  6. 6.

    Sedelmeier J, Ley SV, Lange H, Baxendale IR (2009) Pd-EnCatTM TPP30 as a catalyst for the generation of highly functionalized aryl- and alkenyl-substituted acetylenes via microwave-assisted sonogashira type reactions. Eur J Org Chem. https://doi.org/10.1002/ejoc.200900344

    Article  Google Scholar 

  7. 7.

    Desai B, Kappe CO (2005) Heterogeneous hydrogenation reactions using a continuous flow high pressure device. J Comb Chem 7:641–643. https://doi.org/10.1021/cc050076x

    CAS  Article  PubMed  Google Scholar 

  8. 8.

    Roper KA, Lange H, Polyzos A et al (2011) The application of a monolithic triphenylphosphine reagent for conducting Appel reactions in flow microreactors. Beilstein J Org Chem 7:1648–1655. https://doi.org/10.3762/bjoc.7.194

    CAS  Article  PubMed  PubMed Central  Google Scholar 

  9. 9.

    Elias Y, Rudolf von Rohr P, Bonrath W et al (2015) A porous structured reactor for hydrogenation reactions. Chem Eng Process Process Intensif 95:175–185. https://doi.org/10.1016/j.cep.2015.05.012

    CAS  Article  Google Scholar 

  10. 10.

    Avril A, Hornung CH, Urban A et al (2017) Continuous flow hydrogenations using novel catalytic static mixers inside a tubular reactor. React Chem Eng 2:180–188. https://doi.org/10.1039/c6re00188b

    CAS  Article  Google Scholar 

  11. 11.

    Bagiay AK, Gurariy LL, Kuleshov GG (1988) Physical properties of compounds used in vitamin synthesis. J Chem Eng Data 33:512–518. https://doi.org/10.1021/je00054a035

    Article  Google Scholar 

  12. 12.

    Crespo-Quesada M, Grasemann M, Semagina N et al (2009) Kinetics of the solvent-free hydrogenation of 2-methyl-3-butyn-2-ol over a structured Pd-based catalyst. Catal Today 147:247–254. https://doi.org/10.1016/j.cattod.2008.09.035

    CAS  Article  Google Scholar 

  13. 13.

    Okhlopkova LB, Kerzhentsev MA, Ismagilov ZR (2016) Capillary microreactor with a catalytic coating based on mesoporous titanium dioxide for the selective hydrogenation of 2-methyl-3-butyn-2-ol. Kinet Catal 57:497–503. https://doi.org/10.1134/S0023158416040091

    CAS  Article  Google Scholar 

  14. 14.

    Liguori F, Coiai S, Passaglia E, Barbaro P (2013) Strong cation exchange with innocence: synthesis and characterization of borate containing resins and macroporous monoliths. Macromolecules 46:5423–5433. https://doi.org/10.1021/ma401120v

    CAS  Article  Google Scholar 

  15. 15.

    Kundra M, Bin Mohamad Sultan B, Ng D et al (2020) Continuous flow semi-hydrogenation of alkynes using 3D printed catalytic static mixers. Chem Eng Process - Process Intensif 154:108018. https://doi.org/10.1016/j.cep.2020.108018

    CAS  Article  Google Scholar 

  16. 16.

    Pohanish RP (2002) Sittig’s handbook of toxic and hazardous chemicals and carcinogens. Elsevier Inc, Amsterdam

    Google Scholar 

  17. 17.

    Papa AJ (2003) Amyl Alcohols. Kirk-Othmer encyclopedia of chemical technology. Wiley, Hoboken

    Google Scholar 

  18. 18.

    Corma A, Serna P (2006) Chemoselective hydrogenation of nitro compounds with supported gold catalysts. Science 313:332–334. https://doi.org/10.1126/science.1128383

    CAS  Article  PubMed  Google Scholar 

  19. 19.

    Liu P-L, Zhang H-K, Liu S-H et al (2013) Palladium supported catalysts for nitrocyclohexane hydrogenation to cyclohexanone oxime with high selectivity. ChemCatChem 5:2932–2938. https://doi.org/10.1002/cctc.201300377

    CAS  Article  Google Scholar 

  20. 20.

    Wang X, Perret N, Keane MA (2013) Gas phase hydrogenation of nitrocyclohexane over supported gold catalysts. Appl Catal A 467:575–584. https://doi.org/10.1016/j.apcata.2013.07.061

    CAS  Article  Google Scholar 

  21. 21.

    Lou Y, Xu J, Zhang Y et al (2020) Metal-support interaction for heterogeneous catalysis: from nanoparticles to single atoms. Mater Today Nano 12:100093

    Article  Google Scholar 

  22. 22.

    Park SA, Kim DS, Kim TJ, Kim YT (2013) Strong interaction between Pt and thiolated carbon for electrocatalytic durability enhancement. ACS Catal 3:3067–3074. https://doi.org/10.1021/cs400649n

    CAS  Article  Google Scholar 

  23. 23.

    Diwell AF, Rajaram RR, Shaw HA, Truex TJ (1991) The role of ceria in three-way catalysts. Stud Surf Sci Catal 71:139–152. https://doi.org/10.1016/S0167-2991(08)62975-4

    CAS  Article  Google Scholar 

  24. 24.

    Beamson G, Briggs D (1993) High Resolution XPS of Organic Polymers: The Scienta ESCA300 Database. J. Chem. Educ. 70:A25. https://doi.org/10.1021/ed070pA25.5

    Article  Google Scholar 

  25. 25.

    Voogt EH, Mens AJM, Gijzeman OLJ, Geus JW (1996) XPS analysis of palladium oxide layers and particles. Surf Sci 350:21–31. https://doi.org/10.1016/0039-6028(96)01028-X

    CAS  Article  Google Scholar 

  26. 26.

    Bukhtiyarov AV, Prosvirin IP, Bukhtiyarov VI (2016) XPS/STM study of model bimetallic Pd-Au/HOPG catalysts. Appl Surf Sci 367:214–221. https://doi.org/10.1016/j.apsusc.2016.01.173

    CAS  Article  Google Scholar 

  27. 27.

    Brun M, Berthet A, Bertolini JC (1999) XPS, AES and Auger parameter of Pd and PdO. J Electron Spectros Relat Phenom 104:55–60. https://doi.org/10.1016/s0368-2048(98)00312-0

    CAS  Article  Google Scholar 

  28. 28.

    Serna P, López-Haro M, Calvino JJ, Corma A (2009) Selective hydrogenation of nitrocyclohexane to cyclohexanone oxime with H2 on decorated Pt nanoparticles. J Catal 263:328–334. https://doi.org/10.1016/j.jcat.2009.02.025

    CAS  Article  Google Scholar 

Download references

Acknowledgements

This work was partially sponsored by National Science Centre in Poland within projects UMO-2019/33/B/ST5/01271 and UMO 2018/31/N/ST5/02555.

Funding

National Science Centre in Poland within projects UMO-2019/33/B/ST5/01271 and UMO 2018/31/N/ST5/02555.

Author information

Affiliations

Authors

Contributions

EK: investigation, conceptualization, funding acquisition, methodology. BZ, KM, KN: investigation. AŚ: conceptualization, data curation, formal analysis funding acquisition, methodology, project administration, supervision validation, writing—original draft.

Corresponding author

Correspondence to Anna Śrębowata.

Ethics declarations

Conflict of interest

The authors have no conflicts of interest and have no competing interests to declare that are relevant to the content of this article.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Kowalewski, E., Zawadzki, B., Matus, K. et al. Continuous-flow hydrogenation over resin supported palladium catalyst for the synthesis of industrially relevant chemicals. Reac Kinet Mech Cat 132, 717–728 (2021). https://doi.org/10.1007/s11144-020-01922-5

Download citation

Keywords

  • Flow hydrogenation
  • Resin supported palladium
  • Nitrocyclohexane
  • 2-methyl-3-butyn-2-ol