Abstract
The developed technique for conducting a multilevel study of the operational characteristics, wear, thermal and stress state of ceramic tools has been described. A correlation between the cutting speed and operational characteristics, as well as the thermal state of the cutters with inserts from nitride ceramics, is revealed. Both peculiarities of the tool wear and the role of the thermal factor in the wear mechanism are determined.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Grigor’ev, S.N. and Kuzin, V.V., Prospects for tools with ceramic cutting plates in modern metal working, Glass and Ceramics, 2011, vol. 68, pp. 253–257.
Kuzin, V.V., Thermal state of ceramic cutting tools in high-speed cutting, Russ. Eng. Res., 2004, vol. 24, pp. 32–40.
Szafran, M., Bobryk, E., Kukla, D., and Olszyna, A., Si3N4-Al2O3-TiC-Y2O3 composites intended for the edges of cutting tools, Ceramics Int., 2000, vol. 26, pp. 579–582.
Zhao Xingzhong, Liu Jiajun, Zhu Baoliang, Miao Hezhou, and Luo Zhenbi, Wear behavior of Si3N4 ceramic cutting tool material against stainless steel in dry and water-lubricated conditions, Ceramics Int., 1999, vol. 25, pp. 309–315.
Bitterlich, B., Bitsch, S., and Friederich, K., SiAlON based ceramic cutting tools, J. Eur. Ceramic Soc., 2008, vol. 28, pp. 989–994.
Kuzin, V.V., Grigor’ev, S.N., and Ermolin, V.N., Stress inhomogeneity in a ceramic surface layer under action of an external load. Part 4. Combined effect of force and thermal loads, Refract. Indust. Ceram., 2014, vol. 55, pp. 40–44.
Grigor’ev, S.N., Kuzin, V.V., Morgan, M.N., and Batako, A., Influence of loads on the stress-strain state of aluminum-oxide ceramic cutting plates, Russ. Eng. Res., 2012, vol. 32, pp. 61–67.
Volosova, M.A. and Kuzin, V.V., Regular features of wear of cutting plates from oxide and nitride ceramics, Metal Sci. Heat Treat., 2012, vol. 54, pp. 41–46.
Kuzin, V.V., Volosova, M.A., and Fedorov, M.Yu., Wear of tools from nitride ceramics when machining nickel-based alloys, J. Frict. Wear, 2013, vol. 34, pp. 199–203.
Kuzin, V.V., Effective use of high density ceramic for manufacture of cutting and working tools, Refract. Indust. Ceramics, 2011, vol. 51, pp. 421–426.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © V.V. Kuzin, S.N. Grigoriev, M.A. Volosova, 2014, published in Trenie i Iznos, 2014, Vol. 35, No. 6, pp. 728–734.
About this article
Cite this article
Kuzin, V.V., Grigoriev, S.N. & Volosova, M.A. The role of the thermal factor in the wear mechanism of ceramic tools: Part 1. Macrolevel. J. Frict. Wear 35, 505–510 (2014). https://doi.org/10.3103/S1068366614060099
Received:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068366614060099