Abstract
When producing castings of wide-interval magnesium alloys, their structure is the factor that most decisively affects a complex of mechanical, manufacturing, and operational properties. The specified structure of alloys of the Mg–Al–Zn system is impossible without using the melt modification operation in the smelting manufacturing process. In this work, the results of studying the modification of the ML5 magnesium alloy by different substances are presented. The influence of introducing magnesite into the melt in an amount of 0.4–0.45 wt % at 720–740°C, as well as the influence of melt blowing by oxygen-free carbon-bearing gases at the same temperature on the structure of the alloy and conservation duration of the modification effect is investigated. The latter is especially important in the large-scale and mass production of small castings made of alloys of the Mg–Al–Zn–Mn system when the melt pouring process is prolonged. It is shown that the use of oxygen-free carbon-bearing gases to modify the ML5 alloy provides the attainment of the level of mechanical properties of castings elevated by the 15–20% level of mechanical properties of castings when compared with the standard one according to GOST (State Standard) 2856–79. The conservation efficiency of the duration of the modifying effect by the conventional method (magnesite) is compared with using oxygen-free carbon-bearing gases. It is shown that the modification effect by magnesite is retained no longer than 30–40 min, while, when using oxygen-free carbon-bearing gas, it is no shorter than 4 h, which makes it possible to perform the prolonged pouring of a melt over molds.
Similar content being viewed by others
REFERENCES
Blawert, C., Hort, N., and Kainer, K.V., Automotive applications of magnesium and its alloys, Trans Indian Inst. Met., 2004, vol. 57, no. 4, pp. 397–408.
Garmo, E., Black, J.T., and Kohser, R.A., Magnesium and magnesium alloys, in Materials and Processes in Manufacturing, Upper Saddle River, NJ: Prentice-Hall, 1997, pp. 182–184, 8th ed.
Polmear, I.J., Magnesium alloys and applications, Mater. Sci. Technol., 1994, vol. 10, no. 1, pp. 1–14.
Kulekci, M.K., Magnesium and its alloys applications in automotive industry, Int. J. Adv. Manuf. Technol., 2008, vol. 39, nos. 9–10, pp. 851–865.
Chukhrov, M.V., Modifitsirovanie magnievykh splavov (Modification of Magnesium Alloys), Moscow: Metallurgiya, 1972.
Huang, Z.H., Guo, X.F., and Zhang, Z.M., Effects of alloying on microstructure and mechanical property of AZ91D magnesium alloy, Rare Met. Mater. Eng., 2006, vol. 35, no. 3, pp. 363–366.
Haßlinger, U., Hartig, C., Hort, N., and Günther, R., Modification of magnesium alloys by ceramic particles in gravity die casting, Int. J. Metal., 2014, vol. 2014, article ID 748595.
Tang, B., Wang, Xs., Li, S.S., Zeng, D.B., and Wu, R., Effects of Ca combined with Sr additions on microstructure and mechanical properties of AZ91D, Mater. Sci. Technol., 2005, vol. 21, no. 5, pp. 574–578.
Koltygin, A.V. and Plisetskaya, I.V., Revisiting the behavior of calcium in magnesium casting alloys of Mg–Al–Zn–Mn system, Liteinoe Proizvod., 2010, no. 8, pp. 2–6.
Belov, V.D., Koltygin, A.V., Belov, N.A., and Plisetskaya, I.V., Innovations in cast magnesium alloys, Metallurgist, 2010, vol. 54, nos. 5–6, pp. 317–321.
Fusheng Pan, Mingbo Yang, and Xianhua Chen, A Review on casting magnesium alloys: modification of commercial alloys and development of new alloys, J. Mater. Sci. Technol., 2016, vol. 32, no. 12, pp. 1211–1221.
Al’tman, M.B., Lebedev, A.A., and Chukhrov, M.V., Plavka i lit’e legkikh splavov (Smelting and Casting of Light Alloys), Moscow: Metallurgiya, 1969.
Qinglin Jin, Jeong-Pil Eom, Su-Gun Lim, Won-Wook Park, and Bong-Sun You, Grain refining mechanism of a carbon addition method in a Mg–Al magnesium alloy. Scripta Mater, 2003, vol. 49, no. 11, pp. 1129–1132.
Voronov, S.M., Izbrannye trudy po legkim splavam (Selected Works on Light Alloys), Moscow: Oborongiz, 1957.
Lichy, P. and Cagala, M., Microstructure and thermomechanical properties of magnesium alloys castings, Arch. Foundry Eng., 2012, vol. 12, no. 2, pp. 49–54.
Sarychikhin, N.A., Al’tman, N.B., Lebedev, A.A., Mukhina, I.Yu., Neifak, E.V., Goncharov, V.B., Tabunov, S.A., and Chistyakova, E.I., USSR Inventor’s Certificate no. 624701, 1978.
Bobryshev, B.L, Moiseev, V.S., Ryakhovskii, A.P., and Popkov, D.V., RF Patent 2623965, 2017.
Fruelling, J.W., Protective atmospheres for molten magnesium, Abstract for Dissertation of PhD, Univ. of Michigan, 1970.
Bobryshev, B.L., Some aspects of melting of Mg–Zn–Zr alloys, Tekhnol. Mashinostr., 2006, no. 11, pp. 5–10.
Bobryshev, B.L., Moiseev, V.S., and Kontorovich, I.V., Protection of magnesium alloys against oxidation when filling molds, Tekhnol. Legk. Splav., 2010, no. 4, pp. 49–54.
Velikiy, V.I., Yares’ko, K.I., Shalomeev, V.A., Tsivirko, E.I., and Vnukov, Y.N., Perspective magnesium alloys with elevated level of properties for the aircraft engine industry, Met. Sci. Heat Treat., 2014, vol. 55, nos. 9–10, pp. 492–498.
Shalomeev, V.A., Lysenko, N.A., Tsivirko, E.I., Luki-nov, V.V., and Klochikhin, V.V., Structure and properties of magnesium alloys with scandium, Metalloved. Term. Obrab. Met., 2008, no. 1, pp. 37–40.
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
The authors claim that they have no conflict of interest.
Additional information
Translated by N. Korovin
About this article
Cite this article
Bobryshev, B.L., Moiseev, V.S., Kipin, I.A. et al. Structure and Properties of the ML5 Alloy for Various Modification Methods. Russ. J. Non-ferrous Metals 60, 504–508 (2019). https://doi.org/10.3103/S1067821219050067
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1067821219050067