Abstract
Background
Isoprene, a volatile C5 hydrocarbon, is an important platform chemical used in the manufacturing of synthetic rubber for tires and various other applications, such as elastomers and adhesives.
Results
In this study, Escherichia coli MG1655 harboring Populus trichocarpa isoprene synthase (PtispS) and the exogenous mevalonate (MVA) pathway produced 80 mg/L isoprene. Codon optimization and optimal expression of the ispS gene via adjustment of the RBS strength and inducer concentration increased isoprene production to 199 and 337 mg/L, respectively. To augment expression of MVA pathway genes, the MVA pathway was cloned on a high-copy plasmid (pBR322 origin) with a strong promoter (Ptrc), which resulted in an additional increase in isoprene production up to 956 mg/L. To reduce the formation of byproducts derived from acetyl-CoA (an initial substrate of the MVA pathway), nine relevant genes were deleted to generate the E. coli AceCo strain (E. coli MG1655 ΔackA-pta, poxB, ldhA, dld, adhE, pps, and atoDA). The AceCo strain harboring the ispS gene and MVA pathway showed enhanced isoprene production of 1832 mg/L in flask culture with reduced accumulation of byproducts.
Conclusions
We achieved a 23-fold increase in isoprene production by codon optimization of PtispS, augmentation of the MVA pathway, and deletion of genes involved in byproduct formation.
Similar content being viewed by others
Background
Isoprene (2-methyl-1,3-butadiene) is an important feedstock for commercial production of synthetic rubber. Moreover, isoprene has higher energy content than other biofuels and is convertible to biofuel blend stocks, such as C10 gasoline, C15 diesel, and jet fuels [1]. Currently, 800,000 tons of isoprene monomer is produced annually from crude oil refineries, and over 95% of isoprene is used to produce cis-1,4-polyisoprene, a synthetic version of natural rubber [2]. As consumption of synthetic rubber has increased in the past decade, the demand for isoprene has also dramatically increased.
Currently, petroleum-based isoprene is the dominant source of isoprene available commercially. However, sustainable supply of isoprene is affected by fluctuations in the price of crude oil, high refining cost and energy consumption, and low recovery yield of pure isoprene from light gases produced by oil cracking (less than 1.7%) [3]. Moreover, the process used to prepare pure isoprene is thought to accelerate greenhouse gas emissions and global warming. As an alternative, biological isoprene (bioisoprene) production has been developing rapidly during the last decade.
Bioisoprene is synthesized by isoprene synthase from dimethylallyl diphosphate (DMAPP) [4], which is derived from the mevalonate (MVA) or methylerythritol phosphate (MEP) pathways (Fig. 1a) [5, 6]. Isoprene synthases have been isolated and characterized from various plant species [7–11], and allows microbial engineering for the production of isoprene [12]. Several reports have described isoprene production using Cyanobacteria, yeast, and Bacillus species engineered to overexpress plant isoprene synthases or the recombinant MVA or MEP pathway [13–15]. Although isoprene has been produced from these engineered microorganisms, the production titer is too low to meet industrial demand. Bacillus sp. are known to natively produce isoprene, and endogenous IspH from the MEP pathway can catalyze isoprene formation from HMBPP [16]. The Bacillus sp. N16-5 strain, which harbors an engineered IspH variant, can produce isoprene at concentrations of up to 352 μg/L/OD. Saccharomyces cerevisiae has been extensively engineered to produce isoprene, resulting in production of 37 mg/L isoprene. Successful isoprene production of 1.26 g/L from CO2 was also obtained following extensive engineering of the cyanobacterium Synechococcus elongates [17]. However, Escherichia coli is currently considered the most promising bacterial host for isoprene production. Zhao et al. [15] constructed an isoprene synthesis pathway in Escherichia coli based on the endogenous MEP pathway by overexpression of the native 1-deoxy-d-xylulose-5-phosphate (DXP) synthase gene (dxs) and the foreign DXP reductoisomerase gene (dxr) from Bacillus subtilis combined with introduction of the ispS gene from Populus nigra, which resulted in isoprene production of 314 mg/L. Isoprene has also been produced at 532 mg/L from recombinant Escherichia coli harboring the ispS gene from Populus alba and the exogenous MVA pathway from Saccharomyces cerevisiae [18]. In another report, the MVA pathway was improved by replacing the upper pathway from Saccharomyces cerevisiae with that of Enterococcus faecalis, which is more efficient [19], and introducing a single amino acid mutation in the Enterococcus faecalis mvaS gene to increase enzyme activity [20]. An Escherichia coli strain harboring the improved MVA pathway produced isoprene at up to 1.09 g/L in flask culture. An exogenous MVA pathway, composed of two different sources of MVA pathway from Enterococcus faecalis and Streptococcus pneumoniae, was also used for isoprene production from recombinant Escherichia coli overexpressing Pueraria montana (Kudzu vine) ispS, resulted in isoprene production of 320 mg/L [21]. Whited et al. achieved heterologous expression of Populus alba ispS and a bacterial/yeast hybrid MVA pathway containing additional Methanosarcina mazei mvk, together with overexpression of the endogenous pgl gene (encoding phosphogluconolactonase in the pentose phosphate pathway) [22]. The engineered Escherichia coli strain was able to produce 60 g/L isoprene in a bioreactor fed-batch culture after optimization of fermentation conditions.
Isoprene synthesis pathway (a) and gene clusters used in this study (b). The light and dark gray arrows represent the wild-type isoprene synthase (PtispS) from Populus trichocarpa and its codon-optimized ispS (sPtispS) for expression in Escherichia coli, respectively. The white and dark gray ovals indicate the original RBS of the pTrc99A vector and the modified RBS with higher ribosomal affinity, respectively. The white arrows represent the genes of the MVA pathway (mvaK1, mvaD, and mvaK2 from Streptococcus pneumoniae; mvaE and mvaS from Enterococcus faecalis; and idi from Escherichia coli)
In this study, we constructed the isoprene synthesis pathway with the ispS gene from Populus trichocarpa and the bacterial hybrid MVA pathway composed of two different genetic sources of Streptococcus pneumoniae and Enterococcus faecalis [19] (Fig. 1b). Expression of both Populus trichocarpa ispS and the hybrid exogenous MVA pathway in Escherichia coli were optimized and balanced to maximize isoprene production. Moreover, the genome of the host Escherichia coli strain was also engineered to reduce byproduct formation. The combination of pathway engineering of isoprene biosynthesis and genome manipulation resulted in a significant improvement in isoprene production.
Results and discussion
Comparison of isoprene production by isoprene synthases
To determine the isoprene productivity of ispS genes from different plants, we compared three isoprene synthases from Populus alba, Pueraria montana (Kudzu vine) and Populus trichocarpa. The isoprene synthases of Populus alba and Pueraria montana have been used in most microbial engineering processes for isoprene production. However, the Km values of Populus alba and Pueraria montana isoprene synthases are relatively high (8.7 and 7.7 mM, respectively) [9, 21]. Populus trichocarpa isoprene synthase has not been used for microbial isoprene production, and its Km value is very low (0.32 mM) [11]. These three isoprene synthase genes were cloned into the pTrc99A vector, yielding pT-PaispS, pT-KispS, and pT-PtispS, respectively (Table 1). The three plasmids were introduced into Escherichia coli MG1655 with the MVA pathway plasmid of pS-NA to generate the recombinant strains MGpPapM, MGpKpM, and MGpPtpM, respectively (Table 1). The strain MGpPtpM harboring pT-PtispS and pS-NA produced 80 mg/L isoprene after 24 h of culture, which was 3.7- and 1.4-fold higher than those of the strains MGpPapM (pT-PaispS and pS-NA) and MGpKpM (pT-KispS and pS-NA), respectively, although there was no significant difference in cell growth among the three recombinant strains (Fig. 2a). The IspS from Populus trichocarpa was found to be superior to the other two isoprene synthases as a biocatalyst for isoprene production in Escherichia coli. Thus, the expression of Populus trichocarpa IspS combined with MVA pathway genes was optimized to enhance the production of isoprene.
a Comparison of three different isoprene synthases (Populus alba, Pueraria montana [Kudzu vine], and Populus trichocarpa) for isoprene production from recombinant Escherichia coli strains harboring the MVA pathway. b Effects of codon optimization and the strong RBS for expression of Populus trichocarpa IspS on isoprene production and cell growth. Culture was carried out in TB medium containing 2.0% (w/v) glycerol for 24 h at 30 °C. Open bars and closed bars represent the values obtained at 12 and 24 h of culture, respectively
Optimization of Populus trichocarpa ispS and MVA pathway gene expression
To enhance the expression of the Populus trichocarpa ispS gene, the gene was codon-optimized and cloned into pTrc99A and pTrc99S (modified pTrc99A with a strong RBS), yielding pT-sPtispS and pTS-sPtispS, respectively (Table 1). The strain MGpsPtpM, which harbored pTS-sPtispS and pS-NA, produced 199 mg/L isoprene, which was increased by 2.5-fold from that of the strain MGpPtpM (pT-PtispS and pS-NA; Fig. 2b), suggesting that the enhanced expression of Populus trichocarpa ispS resulting from codon optimization and the use of a strong RBS significantly increased isoprene production. Thus, further overexpression of isoprene synthase combined with MVA pathway genes was stimulated by isopropyl β-d-1-thiogalactopyranoside (IPTG) induction. The strain MGpsPtpM (pTS-sPtispS and pS-NA) was induced with 0.1 mM IPTG, which resulted in an additional 1.7-fold increase in isoprene production to 327 mg/L (Fig. 3). These data indicated that overexpression of both IspS and the MVA pathway increased the synthesis of isoprene in the engineered Escherichia coli. However, a significant reduction in cell growth was observed with the addition of 0.1 mM IPTG. This growth inhibition was thought to be caused by shortage of DMAPP, which would occur in the strain MGpsPtpM owing to the increased overexpression of IspS from pTS-sPtispS rather than the MVA pathway from pS-NA in the presence of IPTG. Therefore, an increased supply of DMAPP through augmentation of the MVA pathway was required for both recovery of cell growth and achievement of high isoprene production.
The MVA pathway operon in pS-NA, which exhibited a low copy number and a mild lac promoter, was ligated into the isoprene plasmid pTS-sPtispS with a high copy number and a strong trc promoter, yielding pTS-sPtispS-MVA (Fig. 1b; Table 1). The strain MGpsPtM harboring pTS-sPtispS-MVA was cultured and induced with 0.05 and 0.1 mM IPTG to observe the effects of overexpression of the MVA pathway on both isoprene production and cell growth (Additional file 1: Figure S3). Under the induction conditions using 0.05 and 0.1 mM IPTG, cell growth was inhibited, even when isoprene production was not increased. These results may be related to the cellular toxicity arising from intracellular accumulation of IPP and DMAPP owing to the overexpression of the MVA pathway from pTS-sPtispS-MVA [23]. Hence, the culture was carried out with the lower concentrations of IPTG (0.01–0.03 mM; Fig. 4). Although there were no significant difference in cell growth depending on the tested IPTG concentrations, isoprene production varied considerably with the concentration of IPTG, and the highest yield of 974 mg/L was obtained at 0.01 mM IPTG, which was 1.7-fold higher than that obtained in the absence of IPTG (the isoprene production rate and culture broth pH are presented in Additional file 1: Figure S4). Thus, the optimal IPTG concentration for culture induction was found to be 0.01 mM. These results suggested that the overall metabolic balance achieved by optimized overexpression of IspS and the MVA pathway was an important element for isoprene production.
Effects of low IPTG concentrations on isoprene production and cell growth of the MGpsPtM strain (MG1655 harboring pTS-sPtispS-MVA). Culture was carried out in TB medium containing 2.0% (w/v) glycerol for 36 h at 30 °C. IPTG was initially added at concentrations of 0 mM (open squares), 0.01 mM (closed squares), 0.02 mM (closed triangles), and 0.03 mM IPTG (closed circles)
Analysis of byproducts in culture broth of MGpsPtM
Isoprene production was increased by 12-fold (80–974 mg/L) through optimized overexpression of the IspS and MVA pathway. However, the isoprene production titer was still low when considering the amount of carbon source used in the culture, and the culture pH was significantly reduced from 7.0 to 5.3. The formation of acetate, a representative acidic byproduct of Escherichia coli, was analyzed from culture broth of the strain MGpsPtM induced by 0.01 mM IPTG (Additional file 1: Figure S5). Acetate was steadily produced to a final amount of 7.4 g/L during the culture. These data suggested that a significant amount of acetyl-CoA was wasted in the production of acetate rather than isoprene. In order to stimulate production of isoprene in the recombinant Escherichia coli without wasting the carbon source, it may be necessary to prevent the formation of byproducts, such as acetate, by the production strain through genomic manipulation, permitting conservation of the acetyl-CoA pool for production of isoprene through the MVA pathway.
Enhanced isoprene production through reduced byproduct formation in the AceCo strain
To reduce carbon source waste and increase carbon flow to isoprene production, we deleted nine genes involved in the formation of byproducts, including acetate, generating the knockout mutant strain AceCo (Table 1; Fig. 5a; Additional file 1: Table S1). The deleted genes (ackA-pta, poxB, ldhA, dld, adhE, pps, and atoDA)were selected to increase carbon flow to the MVA pathway by maximizing the level of acetyl-CoA through preventing formation of the byproducts derived from acetyl-CoA and its precursor, pyruvate. The ackA-pta and poxB genes were deleted to prevent formation of acetate. At the same time, deletions of ldhA/dld and adhE genes were carried out to prevent formation of lactate and ethanol, respectively. The genes pps and atoDA were deleted to prevent the gluconeogenic conversion of pyruvate to phosphoenolpyruvate and the dissipation of the MVA pathway intermediate acetoacetyl-CoA to acetoacetate, respectively. The strain ApsPtM (the AceCo mutant transformed with pTS-sPtispS-MVA) was cultivated to investigate isoprene production and byproduct formation (Figs. 5b, 6). The ApsPtM strain produced 1832 mg/L of isoprene, which was about twofold higher than the production of the MGpsPtM strain, although the ApsPtM strain consumed less glycerol (4.8 g/L of the final residual glycerol concentration) compared with the complete glycerol consumption of the MGpsPtM strain (Additional file 1: Figure S5). Acetate formation was significantly reduced to 1.4 g/L in strain ApsPtM compared with 7.4 g/L in the strain MGpsPtM. Lactate is a minor byproduct formed in small amounts of less than 0.4 g/L for both strains, although lactate formation by strain ApsPtM was lower than that by strain MGpsPtM. Interestingly, significant amounts of pyruvate (3.15 g/L) accumulated in the culture broth of the strain ApsPtM compared with that (0.22 g/L) of the strain MGpsPtM owing to secretion of the elevated pyruvate in the mutant by blockage of acetate and lactate formation. Accumulation of mevalonate (5.56 g/L) was higher in the culture broth of the mutant strain ApsPtM than that (2.93 g/L) of the wild-type strain MGpsPtM, which could reflect the elevation of acetyl-CoA in the mutant cells because one mevalonate molecule is produced from three acetyl-CoA molecules. There was no detectable accumulation of ethanol, PEP, or acetoacetate in the culture broth of strains MGpsPtM and ApsPtM (data not shown). These results indicated that the acetyl-CoA flux in the ApsPtM strain was directed to the MVA pathway by preventing generation of waste byproducts from pyruvate and acetyl-CoA.
a Pathway of byproduct formation from acetyl-CoA and pyruvate in Escherichia coli. Strikeouts indicate deleted genes in the AceCo strain. The deleted genes and their corresponding enzymes are as follows: ldhA lactate dehydrogenase; dld d-lactate dehydrogenase; pps phosphoenolpyruvate synthetase; poxB pyruvate oxidase; adhE aldehyde-alcohol dehydrogenase; pta phosphate acetyltransferase; ackA acetate kinase; atoD acetoacetyl-CoA transferase; atoA acetoacetyl-CoA transferase. b Analysis of extracellular metabolites (acetate, lactate, pyruvate, and mevalonate) accumulated during the culture of strain MGpsPtM (wild-type MG1655 harboring pTS-sPtispS-MVA) shown in Fig. 4 (open squares) and the strain ApsPtM (the knockout mutant AceCo harboring the same plasmid) shown in Fig. 6 (closed squares) after induction with 0.01 mM IPTG
Conclusion
Taken together, our findings demonstrated that isoprene production could be increased by engineering of the isoprene synthesis pathway based on the MVA pathway and preventing byproduct formation through genome manipulation (Table 2). The combination of codon optimization of Populus trichocarpa isoprene synthase and the introduction of the heterologous MVA pathway resulted in a 4.2-fold increase in isoprene production. Construction of a single plasmid system by transfer of the MVA pathway from pS-NA to pTS-sPtispS, followed by optimal overexpression of these genes with 0.01 mM IPTG, resulted in an additional increase in isoprene production by 12.2-fold. The highest isoprene production of 1832 mg/L was achieved using the AceCo strain by reducing the formation of inhibitory byproducts, such as acetate. Although a considerable increase in isoprene production was attained in this study, mevalonate accumulation was also observed, suggesting that the bottom portion of the MVA pathway were less efficient than the top portion and that the pathway required further engineering to achieve higher efficiency. If the efficiency of the bottom portion in the MVA pathway is enhanced, mevalonate may not accumulate, and acetyl-CoA may flow more easily into the MVA pathway, resulting in further reductions in the accumulation of pyruvate in the AceCo strain by its favorable conversion to acetyl-CoA. Therefore, future studies are needed to engineer the bottom portion of the MVA pathway in order to increase isoprene production further. This may be achieved by identification of the rate limiting step in the bottom portion and replacement of inefficient enzymes with more efficient enzymes or by augmenting the overexpression of the enzyme.
Methods
Bacterial strains and culture conditions
The bacterial strains used in this study are listed in Table 1. Escherichia coli DH5α was used for gene cloning, and Escherichia coli MG1655 was used for isoprene production (Table 1). Culture of isoprene production was carried out in a 300-mL baffled flask containing 50 mL TB medium (24 g/L yeast extract, 12 g/L tryptone, 9.2 g/L K2HPO4, and 2.2 g/L KH2PO4) with 2.0% (w/v) glycerol as the main carbon source. IPTG was added at concentrations of 0.01–0.1 mM. Ampicillin (100 μg/mL) and chloramphenicol (50 μg/mL) were added to the culture as required. Cell growth was determined by measuring the optical density at 600 nm (OD600), and pH was measured using a compact pH meter (B-212; HORIBA, Japan).
Plasmid and strain construction
The plasmids and polymerase chain reaction (PCR) primers used in this study are listed in Table 1. All basic molecular techniques, including genomic or plasmid DNA preparations, restriction enzyme digestions, and transformations, were carried out as described in literature. PCR was performed using Phusion DNA polymerase (Finnzymes Co., Finland) with a standard protocol. pTrc99A (RBS and gap sequences: AGGAAACAGA), pTrc99S (a modified pTrc99A version with a strong RBS and gap sequences: AGGAGGTAATAAA), and pSTV28 plasmids were used for gene expression (Table 1). Translation initiation rates (TIRs) of ispS were 217 and 39,327 for pTrc99A and pTrc99S vectors, respectively. The TIR was calculated with the RBS calculator program (https://salislab.net/; Salis Lab, Penn State University, PA, USA). The pS-NA plasmid containing the MVA pathway operon was used as described previously [19]. Three different ispS genes lacking the transit peptide sequence were amplified using PCR from plasmids harboring ispS genes of Populus alba, Populus trichocarpa, and Pueraria montana, which were kindly provided by Prof. Claudia E. Vickers (University of Queensland, Australia). The PCR products were cloned into the NcoI (followed by Klenow treatment for cloning of ispS genes from Populus alba and Pueraria montana) and XbaI sites of pTrc99A, yielding the isoprene plasmids pT-PaispS, pT-PtispS, and pT-KispS (Table 1). The Populus trichocarpa ispS gene (GenBank accession number: EU693027) was also synthesized by Genscript Inc. (NJ, USA) according to the codon-optimization function of the company’s in-house software for enhanced expression in Escherichia coli. The synthetic ispS gene was cloned into the NcoI and XbaI sites of pTrc99A and pTrc99S, yielding pT-sPtispS and pTS-sPtispS, respectively. The MVA pathway operon from pS-NA was amplified and cloned into the XbaI site of pTS-sPtispS, which resulted in pTS-sPtispS-MVA.
The mutant strain, called AceCo, was derived from Escherichia coli MG1655 by deletions of nine genes related to the formation of inhibitory byproducts, such as alcohol and acids (Table 1). The AceCo strain (Escherichia coli MG1655 ΔackA-pta, poxB, ldhA, dld, adhE, pps, and atoDA) was generated by combination of individual gene knockouts using P1 transduction with phage P1 (ATCC 25404-B1) [24]. The knockout strains and primers used for the construction of the AceCo strain are listed in Additional file 1: Table S1. The seven basal knockout strains (IS1–7) were generated using a gene deletion kit based on Red/ET recombination (Quick and Easy E. coli Gene Deletion Kit; Gene Bridges, Germany) with standard protocols.
Analysis of isoprene, byproducts, and mevalonate
To measure isoprene production, isoprene produced from recombinant Escherichia coli was collected by overlaying a dodecane (C12H26) layer. Dodecane has properties of low toxicity to Escherichia coli [25], low volatility, and high hydrophobicity (log PO/W, 6.6) and is suitable for recovery of hydrophobic isoprene. The culture broth, 0.7 mL was sampled every 2 h and incubated with an equal volume of dodecane in 1.5 mL Eppendorf tube at 30 °C with shaking at 150 rpm for 10 min. The dodecane phase was separated from the culture broth by centrifugation at 10,000 rpm for 10 s. The separated dodecane phase containing isoprene was analyzed using an Agilent Technologies 7890A Gas Chromatograph equipped with a flame ionization detector (FID). Briefly, 5 μL of each sample was separated on a 19091N-133 HP-INNOWAX column (length, 30 m; internal diameter, 0.25 mm; film thickness, 250 μm). The oven temperature was initially held at 50 °C for 2 min and then gradually increased to 250 °C at a rate of 30 °C/min. Nitrogen was used as the carrier gas with an inlet pressure of 15.345 psi. The detector temperature was maintained at 280 °C. All the works were carried out in speedy to minimize volatile loss of isoprene. The retention time of the isoprene standard was 1.38 min (Additional file 1: Figure S1). The standard curve of isoprene was constructed using isoprene (Sigma, USA) dissolved in dodecane for quantification of isoprene production (Additional file 1: Figure S2). A sealed glass bottle was used for dilution of chilled standard isoprene to make the standard curve. The dilution work was done very quickly and the glass bottle was kept sealed except the quick addition of isoprene standards.
Byproducts, including acetate, lactate, pyruvate, and ethanol, in culture broth were analyzed with high-performance liquid chromatography (HPLC; LC-20A; Shimadzu, Kyoto, Japan) at a detection wavelength of 210 nm with an ion exchange HPLC column (Aminex; HPX-87H, 7.8 × 300 mm; Bio-Rad, USA). The mobile phase of 5 mM H2SO4 was used at a flow rate of 0.6 mL/min, and the column temperature of 40 °C was applied. The residual glycerol was analyzed by HPLC equipped with an RID detector (RID-10A; Shimadzu) and hydrophobic interaction HPLC column (100-5NH2, 250 × 4.6 mm; Kromasil, Sweden). The mobile phase of 75% acetonitrile was used at a flow rate of 1.5 mL/min, and a column temperature of 40 °C was applied for the analysis. Acetate, lactate, pyruvate, and ethanol were purchased from Sigma, dissolved in distilled water, and used as standard compounds.
The mevalonate concentration was determined by gas chromatography (GC) analysis. The culture filtrate was adjusted to pH 2.0 with 3 M HCl, incubated at 45 °C for 1 h, saturated with anhydrous Na2SO4, and extracted with ethylacetate. The resulting samples were analyzed for quantification of mevalonate using GC. The analytical temperature of the GC was controlled at an initial temperature of 180 °C for 1 min, then ramped to 200 °C gradually at 2.5 °C/min and held for 2 min. The detector temperature was maintained at 260 °C. The mevalonate standard compound was prepared from mevalonolactone (Sigma-Aldrich) as described in a previous report [26].
Abbreviations
- DMAPP:
-
dimethylallyl diphosphate
- MVA:
-
mevalonate
- MEP:
-
methylerythritol 4-phosphate
- DXP:
-
1-deoxy-d-xylulose-5-phosphate
- IPP:
-
isopentenyl diphosphate
- TIR:
-
translation initiation rate
References
Zhang H, Suvorov M, Hutcheson SW. Compositions and methods for the production of isoprene. US Patent, 2012.
Greve H-H. Rubber, 2. Natural. In: Ullmann’s encyclopedia of industrial chemistry. Weinheim: Wiley; 2000.
Lv X, Xie W, Lu W, Guo F, Gu J, Yu H, Ye L. Enhanced isoprene biosynthesis in Saccharomyces cerevisiae by engineering of the native acetyl-CoA and mevalonic acid pathways with a push-pull-restrain strategy. J Biotechnol. 2014;186:128–36.
Schwender J, Zeidler J, Groner R, Muller C, Focke M, Braun S, Lichtenthaler FW, Lichtenthaler HK. Incorporation of 1-deoxy-d-xylulose into isoprene and phytol by higher plants and algae. FEBS Lett. 1997;414:129–34.
Goldstein JL, Brown MS. Regulation of the mevalonate pathway. Nature. 1990;343:425–30.
Rohmer M. The discovery of a mevalonate-independent pathway for isoprenoid biosynthesis in bacteria, algae and higher plants. Nat Prod Rep. 1999;16:565–74.
Miller B, Oschinski C, Zimmer W. First isolation of an isoprene synthase gene from poplar and successful expression of the gene in Escherichia coli. Planta. 2001;213:483–7.
Sasaki K, Ohara K, Yazaki K. Gene expression and characterization of isoprene synthase from Populus alba. FEBS Lett. 2005;579:2514–8.
Sharkey TD, Yeh S, Wiberley AE, Falbel TG, Gong D, Fernandez DE. Evolution of the isoprene biosynthetic pathway in kudzu. Plant Physiol. 2005;137:700–12.
Vickers CE, Possell M, Nicholas HC, Mullineaux PM. Genetic structure and regulation of isoprene synthase in Poplar (Populus spp.). Plant Mol Biol. 2010;73(4–5):547–58.
Wiberley AE, Donohue AR, Meier ME, Westphal MM, Sharkey TD. Regulation of isoprene emission in Populus trichocarpa leaves subjected to changing growth temperature. Plant Cell Environ. 2008;31(2):258–67.
Ye L, Lv X, Yu H. Engineering microbes for isoprene production. Metab Eng. 2016;38:125–38.
Lindberg P, Park S, Melis A. Engineering a platform for photosynthetic isoprene production in cyanobacteria, using Synechocystis as the model organism. Metab Eng. 2010;12:70–9.
Xue J, Ahring BK. Enhancing isoprene production by genetic modification of the 1-deoxy-d-xylulose-5-phosphate pathway in Bacillus subtilis. Appl Environ Microbiol. 2011;77:2399–405.
Zhao Y, Yang J, Qin B, Li Y, Sun Y, Su S, Xian M. Biosynthesis of isoprene in Escherichia coli via methylerythritol phosphate (MEP) pathway. Appl Microbiol Biotechnol. 2011;90:1915–22.
Ge D, Xue Y, Ma Y. Two unexpected promiscuous activities of the iron–sulfur protein IspH in production of isoprene and isoamylene. Microb Cell Fact. 2016;15:79.
Gao X, Gao F, Liu D, Zhang H, Nie X, Yang C. Engineering the methylerythritol phosphate pathway in cyanobacteria for photosynthetic isoprene production from CO2. Energy Environ Sci. 2016;9:1400–11.
Yang J, Xian M, Su S, Zhao G, Nie Q, Jiang X, Zheng Y, Liu W. Enhancing production of bio-isoprene using hybrid MVA pathway and isoprene synthase in E. coli. PLoS ONE. 2012;7:e33509.
Yoon SH, Lee SH, Das A, Ryu HK, Jang HJ, Kim JY, Oh DK, Keasling JD, Kim SW. Combinatorial expression of bacterial whole mevalonate pathway for the production of beta-carotene in E. coli. J Biotechnol. 2009;140:218–26.
Steussy CN, Robison AD, Tetrick AM, Knight JT, Rodwell VW, Stauffacher CV, Sutherlin AL. A structural limitation on enzyme activity: the case of HMG-CoA synthase. Biochemistry. 2006;45:14407–14.
Zurbriggen A, Kirst H, Melis A, Department of Plant and Microbial Biology UoC. Isoprene production via the mevalonic acid pathway in Escherichia coli (Bacteria). Bioenergy Res. 2012;5:814–28.
Whited GM, Feher FJ, Benko DA, Cervin MA, Chotani GK, McAuliffe JC, LaDuca RJ, Ben-Shoshan EA, Sanford KJ. Development of a gas-phase bioprocess for isoprene-monomer production using metabolic pathway engineering. Ind Biotechnol. 2010;6:152–63.
Martin VJ, Pitera DJ, Withers ST, Newman JD, Keasling JD. Engineering a mevalonate pathway in Escherichia coli for production of terpenoids. Nat Biotechnol. 2003;21:796–802.
Thomason LC, Costantino N, Court DL. E. coli genome manipulation by P1 transduction. In: Curr Protoc Mol Biol, Chapter 1: Unit 1. 2007. p. 17.
Ramos JL, Duque E, Gallegos MT, Godoy P, Ramos-Gonzalez MI, Rojas A, Teran W, Segura A. Mechanisms of solvent tolerance in gram-negative bacteria. Annu Rev Microbiol. 2002;56:743–68.
Kim CM, Goldstein JL, Brown MS. cDNA cloning of MEV, a mutant protein that facilitates cellular uptake of mevalonate, and identification of the point mutation responsible for its gain of function. J Biol Chem. 1992;267:23113–21.
Authors’ contributions
SWK, ESC and JHK conceived the study and designed the experiments. JHK, HJJ, MSC and YSJ carried out the experiments. JHK, CLW and JEP analyzed the data. JHK, CLW and SWK drafted the manuscript. All authors read and approved the final manuscript.
Acknowledgements
We thank Prof. Claudia E. Vickers (The University of Queensland) for providing the plasmids harboring ispS genes of P. trichocarpa and Kudzu vine.
Competing interests
The authors declare that they have no competing interests.
Availability of data and materials
The datasets supporting the conclusions of this article are included within the article and its Additional file 1.
Funding
This work was supported by C1 Gas Refinery Program through the NRF funded by the MSIP (NRF-2016M3D3A1A01913246), a Grant (NRF-2012M1A2A2671831) from the National Research Foundation, MSIP, and a grant from the Next-Generation BioGreen 21 Program (SSAC, Grant#: PJ01106201), RDA, Korea. JH Kim is supported by scholarships from the BK21 Plus Program, MEST, Korea. The funding bodies played no role in the design and execution of the study, nor in the writing of this article.
Author information
Authors and Affiliations
Corresponding authors
Additional file
12934_2016_612_MOESM1_ESM.doc
Additional file 1: Table S1. Primers and strains used for the construction of E. coli AceCo strain. Figure S1. Chromatogram of isoprene standard dissolved in dodecane. Figure S2. Standard curve of isoprene. Figure S3. Effect of IPTG induction on isoprene production and cell growth of MGpsPtM strain (MG1655 harboring pTS-sPtispS-MVA). Figure S4. Effect of low IPTG concentrations on isoprene production rate and culture broth pH in the culture of MGpsPtM strain (MG1655 harboring pTS-sPtispS-MVA). Figure S5. Acetate formation and glycerol consumption of the 0.01 mM IPTG induced culture of MGpsPtM in Fig. 4.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated.
About this article
Cite this article
Kim, JH., Wang, C., Jang, HJ. et al. Isoprene production by Escherichia coli through the exogenous mevalonate pathway with reduced formation of fermentation byproducts. Microb Cell Fact 15, 214 (2016). https://doi.org/10.1186/s12934-016-0612-6
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s12934-016-0612-6