Abstract
Electronics devices growth in the last decade of the twentieth century ushered in a revolution inside the electronics segment. Continuous micro-sizes and operation cause these devices to heat up, resulting in a reduction in their performance or damage to their parts. Because heat can decrease device performance and life span while also wasting energy, offering an incorporated and effective cooling system has become a significant part of the design of device equipment. One of the key challenges of modern generation technology is the cooling of electronic devices. Nanofluids have attracted attention in a broad range of engineering implementations due to their great properties, which may be used to effectively cool devices while also improving energy efficiency. In view of the above defects, this numerical research object to examine the chip surface temperature, heat transfer rate, thermal resistance, Darcy friction factor and reliability of microelectronic chips in minichannel heat sinks is scrutinized by utilizing a \({\text{TiO}}_{2}\)/water nanofluid as a coolant and comparing the nanoliquid outcomes with the outcomes of water. \({\text{TiO}}_{2}\)/Water nanofluids at 1%, 2% and 3% volume concentrations are employed for this scrutinization. Here, a commercial CFD ANSYS (R19.2) FLUENT software package is used to analyze the electronic chip performance. The CFD ANSYS (R19.2) FLUENT software package is used for modeling, meshing and simulation of the current study.
Similar content being viewed by others
Introduction
Currently, modern electronic machinery generates strong heat fluxes. As a result, advanced electronic machinery, such as integrated circuits, electronic chips and computer microprocessors, demands large thermal dissipation rates for cooling. Heat sinks are technologies to remove heat generated from electronic processors with the help of the energy difference between the warming surface and the coolant. The objectives of using heat sinks are divided into two categories: (I) to improve the rate of heat dissipation to improve the efficiency of electronic devices and (II) to increase the electrical package dependability and performance. It is generally acknowledged that electronic chip malfunction and excessive energy consumption are caused by shrinking electronic component dimensions, which drastically boosts heat flux per unit area, resulting in heat difficulties and deterioration in chip efficiency and reliability. One of the most difficult problems in the creation of next-generation circuit boards, microprocessors, and other tiny integrated memory chips is addressing these challenges. Several kinds of heat exchangers and cooling processes are currently used in electrical cooling. Electronic cooling can be accomplished using a variety of approaches, including jet impingement cooling, pool boiling, two-phase flow in microchannels, spray cooling, and heat pipes. In the past, air-based cooling methods were widely used. However, due to the poor thermal transportation properties of air, they have some drawbacks1,2. Water-based strategies were later used to overcome the drawbacks of the air cooling process. According to many researchers, the thermal efficiency of water-based systems is significantly better than that of air-based systems. However, because of the latest developments in micro- and nanoscale heat transfer components, the heat efficiency of water-based systems may be limited in their ability to eliminate large heat fluxes from advanced electronic devices. Li3 proposed a nanofluid flow through microchannel. Paisarn and Lursukd4 examined the heat sink impact on minirectangular fins to improve the thermal performance through nanofluids. The output demonstrated that the thermal efficiency rate for nanoliquids is greater than that for deionized water. Farsad et al.5 scrutinized the numerical computations of microchannel heat sinks utilizing nanofluids and found that the microchannel heat sink cooling performance was better than that of pure water in minichannel heat sinks. Saadoon et al.6 explored the thermal transportation of nanofluids in minichannel heat sinks.
Although common working fluids have poor thermal characteristics, it appears that using fluids with improved heat characteristics rather than ordinary fluids is required7,8. Solids, on average, have stronger heat conductivities than base liquids8. Therefore, it appears that scattering solid particles in host fluid may improve the heat proficiency of host fluid9,10. Tiny-sized particles are unstable and sediment, whereas Choi11 demonstrated that tiny-sized particles disperse faster than micron-sized particles. These nanofluid suspensions have greater heat conductivities than the base liquid12. Muhammad et al.13 investigated the numerical computations of Eyring-Powell nanofluids over three-dimensional surfaces with Arrhenius activation energy. Sheikholeslami et al.14 examined the thermal performance impacts on copper/water nanoliquids by adopting CVFEM. Wakif et al.15 investigated magneto nanofluid flow through horizontal layers. Khan et al.16 discussed the behavior of Casson blood base nanofluid flow through a rotating disk.
In various areas, nanofluids with high heat efficiency have been commonly utilized rather than conventional media (such as water and oil) to fulfill the demand of high-performance heat transfer media. Currently, nanoliquids have been recommended by the majority of researchers in the field of solar energy. Yu et al.17 suggested that CuO/Ag nanoliquids with a volume of 0.025 percent have the best photothermal renovation capacity. This helps to improve the transfer of energy between light and heat in the solar heat collector packed with nanoliquids. Moghadam et al.18 discussed copper oxide/water nanofluid flow through plates inside a solar collector.
Computational fluid dynamics (CFD) approaches are strong tools for simulating fluid flow and associated heat and solutal transport by computing a numerically mathematical system that governs these processes, taking use of rapid and ongoing advances in computers and computing methodologies. Extensive comprehensive examination, fundamental investigations of redesign and new systems, in-depth product research & innovation, and troubleshooting are all areas where CFD simulations are useful19. In comparison to analytical and experimental fluid dynamics, CFD is highly significant in computations of microelectromechanical system (MEMS) technologies, particularly in the design of effective microchannel heat sinks. Adopting CFD modeling tools in invention and design saves time and cost when compared to experimental techniques. Klazly and Bognár20 analyzed the CFD computations of nanofluid flow influenced by flat plates. Mohammed et al.21 used a rectangular tube to analyze nanofluids. Naphon and Nakharintr22 examined the numerical computations of nanofluids in microchannel heat sinks.
The fast demand for electronic equipment necessitates the development of small advanced cooling technology that can deliver higher performance and reliability. Electronic equipment faces challenges such as excessive power consumption and short life. Many electronic cooling strategies are being introduced by researchers. One of them is a desire to learn more about electronics cooling. Many scientists have scrutinized the significance of several nanofluid combinations on the cooling performance of electrical devices. The advent of current technology has resulted in a reduction in the dimensions of industrial equipment in recent years. However, adequate cooling and energy removal is a major issue in utilizing such equipment, especially in electronic systems. As a result, improving the thermal efficiency of systems has become extremely important. Based on the abovementioned survey of the literature, a few analyses have focused on circular microchannel heat sinks with fins by utilizing water-based suspensions with \({\text{TiO}}_{2}\) nanoparticle applications for heat transfer in electronic chips. Therefore, to fill this gap of investigation, we tried to improve the cooling proficiency of electronic chips in regular six-channel heat sinks by using a \({\text{TiO}}_{2}\)/water nanofluid utilizing the numerical finite volume method. The main purposes are mainly as follows:
-
The impacts of the heat transfer rate, Nusselt number, Darcy friction factor, thermal resistance and reliability of the electronic chip on the microchannel heat flux are scrutinized.
-
The effects of the surface temperature of the chip and \({\text{TiO}}_{2}\)/water nanofluid behavior as a coolant are investigated.
-
Here, the cooling efficiency of nanofluid \(\phi = 1\% ,\phi = 2\% ,\phi = 3\%\) in a microchannel heat sink is scrutinized numerically by utilizing CFD ANSYS-Fluent.
-
The modeling, meshing and simulation are explored by using computational CFD ANSYS-FLUENT (R19.2).
-
The flow governing system of equations is approached numerically by adopting the finite volume method (FEM) in ANSYS-FLUENT (R19.2).
Mesh specifications/generation
Mesh independence study
Throughout the mesh independence study, three different cases were carried out: (I) coarse, (II) normal and (III) fine. After the analysis, we found a fine mesh to be given accurate results and of good quality. The mesh characteristics are reported in Table 1. Eight dissimilar grids were utilized to confirm that outcomes were not dependent on the grid. The Nusselt number and Heat transfer outcomes (depicts in Table 2) are utilized as the indicators of the outcomes. Due to diverse outcomes, the fifth grid was preferred as final grid. Reasons for choosing a fifth grid are summarized below:
-
Better and smoother solution convergence at good criteria.
-
Much better accuracy.
-
Structured multi zone mixed cells mesh along with much better quality as compared to other meshes.
-
Feasible Results in relatively less computational time.
For current simulation purposes, a machine with the following specification is utilized:
-
1.
Ram: 12 GB.
-
2.
Processor: Intel core i5.
-
3.
Time: 30 min iteration 100.
-
4.
Convergence at 100 iteration.
Meshing of the microchannel with a heat sink was performed with the help of a commercial ANSYS-FLUENT (R19.2) tool. Figure 1 shows the mesh of the microchannel heat sink in cases of skewness, element quality and mash of six microchannels.
Methodology
Problem description
CFD modeling is now a well-established practice for computing complex issues in various modern engineering sectors because it is convenient. Here, the three-dimensional laminar flow of steady state from the laws of conservation of mass, momentum and energy is taken into account. A physical view of the problem under a heat sink with a microchannel is displayed in Figs. 2 and 3. According to the figure, six microchannels and five fins are installed with a chip to increase the cooling proficiency. The microchannel dimensions are width = 55 mm, length = 55 mm and height = 42 mm, as mentioned in Table 3. The microchannel in the heat sink and identical cross section of channels are shown in Fig. 4. To approximate the heat generation in the electronic chip, a uniform heat flux (\(q^{\prime\prime} = 70\,\,{\text{W}}/{\text{cm}}^{2}\)) is employed on the base wall surface of the channel heat sink. In this article, \({\text{TiO}}_{2}\) nanoparticles with a diameter of 35 mm were dispersed in water as a coolant. The computational package Fluent, which uses the finite volume method, is a popular program for computing fluid flows. Figure 5 are drawn for mash of microchannel heat sink in three different view (i) side view and five fins (ii) bottom view (iii) microchannel heat sink by utilizing ANSYS (i.e., CFD FLUENT) computational software.
The following governing equations are taken into account with consideration, such as laminar, incompressible and steady-state fluid flow, for the current issue:
Equation of Continuity
Equations of Momentum are:
Heat equation for coolant:
Heat equation for solid phase:
Here, \(\rho_{f}\) indicates the density of the fluid, \(\mu_{f}\) signifies the dynamic viscosity, \(T_{f}\) designates the temperature of the coolant, \(p\) denotes the coolant pressure, the specific heat capacity is indicated as \(C_{pf}\) and \(K_{f}\) is the thermal conductivity.
Boundary conditions
The boundary layer flow equations were approached utilizing a commercial CFD package (Fluent 19.2). The volumetric concentration of \({\text{TiO}}_{2}\) nanoparticles dispersed in distilled water utilized as the input constraint was 1–3%, and the inlet temperature was \(293.15\,{\text{K}}\) to the microchannel heat sink. The coolant used in this computation through the inlet is water and \({\text{TiO}}_{2}\)/water nanoliquid, and its thermophysical characteristics are mentioned in Table 4. In this investigation, a single phase is considered. ANSYS-FLUENT (R19.2)23 is used for modeling the microchannel heat sink. Here, the nodes and elements of the microchannel heat sink are 174,216 and 421,945, respectively. A uniform heat flux \(q^{\prime\prime} = 70\,\,{\text{W}}/{\text{cm}}^{2}\) is used on the base of the chip surface to simulate heat generation in electronic chips. No slip was implemented in any domain of the fluid.
Thermophysical characteristics of nanofluid
The thermophysical characteristics of the nanofluid, such as density (\(\rho\)), heat capacity (\(C_{p}\)), dynamic viscosity (\(\mu\)) and thermal conductivity (\(k\)), are addressed by24 (see Table 5).
Data reduction
The heat transfer rate is obtained by:
The coefficient of heat transfer is addressed as;
The average Nusselt number is characterize as:
The Darcy friction factor along the microchannel heat sink is examined to compute the hydraulic loss of the microchannel flow24
Here, \(\Delta p\) indicates the difference in pressure between the inlet and outlet of the minichannel heat sink \(f_{r}\) is the friction factor and \(L\) is the length of the microchannel.
Based on hydraulic diameter, the Reynolds number is computed as25,
The overall thermal resistance is determined by
The Arrhenius expression is addressed by26
The Failure rate26 is obtained by following
The MTTF (i.e., Mean Time to Failure) is calculated as26:
Numerical analysis/CFD methodology
In this investigation, commercial ANSYS-FLUENT (R19.2) CFD software was utilized to compute numerically governing equations. The mesh of the microchannel for the electronic ship is computed at fine quality by utilizing ANSYS-FLUENT (R19.2) (see Fig. 5). Here, the microchannel heat sink for an electronic chip utilizing a \({\text{TiO}}_{2}\)/distilled water nanofluid is illustrated by a single phase with uniform heat flux \(q^{\prime\prime} = 70\,\,{\text{W}}/{\text{cm}}^{2}\) affected on the bottom chip surface. The governing flow equations are integrated utilizing FVM with CFD ANSYS FLUENT software. The computations were based on the pressure correction technique utilizing the SIMPLE scheme.
Results and discussion
In this numerical study, the heat transfer in electronic chip in six circular channel heat sink can be divided into two based on the mechanisms namely, simple water and \({\text{TiO}}_{2}\)/water nanofluid. The thermal transfer rate, Nusselt number, Darcy friction factor, Reynolds number, thermal resistance, and wall temperature are discussed and compared with the outcomes of water. Nanopowder of \({\text{TiO}}_{2}\) is that this particular nanofluid is unique as compared with other nano fluid especially when it comes to heat transfer. The computations address dissimilar values of the volume friction of \({\text{TiO}}_{2}\)/water nanoliquids, such as \(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\). The single-phase \({\text{TiO}}_{2}\)/water nanofluid in the microchannel heat sink is studied numerically with uniform heat flux \(q^{\prime\prime} = 70\,\,{\text{W}}/{\text{cm}}^{2}\) on the base of the chip.
Velocity profile
The velocity field across the microchannel heat sink for the \({\text{TiO}}_{2}\)/water nanofluid is plotted in Fig. 6. The variation in the velocity field \(1587\,\,{\text{ms}}^{ - 1}\) is obtained at the \(3\%\) volume friction of the nanofluid. It can be observed that the thermophysical properties are altered with respect to volume friction. Here, we found that velocity decreases as the volume friction in the nanofluid increases. The cross-sectional view of velocity across inlet to outlet is displayed in Fig. 7. The velocity decreases at the inlet to outlet faces for each volume friction under the Reynolds number. Furthermore, the density and viscosity of the nanofluid increases via superior volume friction impact under the same Reynolds number.
Heat transfer
The major aim of the cooling system is to decrease the surface temperature of the heat sink in minichannels with electronic chips. Figure 8 signifies the variation of heat transfer coefficient as a function of inlet velocity with distinguished amount of volume friction of \({\text{TiO}}_{2}\)/water nanofluid such as \(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\). The heat transfer coefficient has a direct direction with the inlet velocity of the fluid. Therefore, the heat transfer coefficient improves with increasing inlet velocity of the fluid. The coefficient of heat transfer is observed from \(12.09\) to \(14.02\%\) at a volume friction of \({\text{TiO}}_{2}\)/water nanofluid from 1 to \(3\%\). Figure 9 illustrates the heat transfer coefficient against the Reynolds number for distilled water and three different amounts of volume friction \(1\%\) to \(3\%\). A larger Reynolds number has a larger heat transfer coefficient, with the volume friction distinguishing values from 1 to \(3\%\) of the \({\text{TiO}}_{2}\)/water nanofluid in the microchannel heat sink. Furthermore, the heat transfer rate is larger from \(12.09\) to \(14.02\%\) in the case of \({\text{TiO}}_{2}\)/water nanofluids compared to water. This improvement due to the superior merging of \({\text{TiO}}_{2}\) particles and collision of particles as a result of heat efficiency carries out more heat proficiency.
The 3D graph impacts of HTC w.r.t active parameters are plotted in Fig. 10. Similarly, Fig. 11 demonstrates the contour diagram of the heat transfer coefficient (HTC) to indicate the largest and smallest amount.
Nusselt number
The significance of inlet fluid velocity on the Nusselt number with three different values of \({\text{TiO}}_{2}\)/water nanofluid volume friction \(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\) is displayed in Fig. 12. We observed that the use of \({\text{TiO}}_{2}\)/water nanoliquids in microchannel heat sinks with heat flux escalates the thermal transfer rate. As mentioned earlier, the use of different volume friction (\(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\)) of nanofluids leads to an enhanced Nusselt number. From the figure, it can be noticed that the Nusselt number is an improving function of inlet fluid velocity.
Figure 13 is captured to determine the trend of the Reynolds number against the Nusselt number with volume friction (\(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\)) of \({\text{TiO}}_{2}\)/water nanofluids in a microelectronic chip with six microchannel heat sinks. From the CFD analysis, we found that the Nusselt number is improved by escalating the values of the Reynolds number. Furthermore, the Nusselt number is, \(12.17\%\), \(12.39\%\) and \(14.01\%\) larger than water for different \(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\) \({\text{TiO}}_{2}\)/water nanoliquids, respectively. Physically, the convective thermal transfer current is improved due to the presence of a better Reynolds number. Therefore, the Nusselt number is more effective for \({\text{TiO}}_{2}\)/water nanoliquids than water.
Figure 14 illustrates a 3D plot of the heat transfer rate (HTR) against the volume friction and Reynolds number. Here, we noticed that HTR is enhanced when the Reynolds number is boosted for each volume friction. Similarly, the contour of HTR versus active parameters is captured in Fig. 15.
Thermal resistance
Figure 16 demonstrates the thermal resistance values for dissimilar values of \({\text{TiO}}_{2}\)/water nanofluid volume fractions versus Reynolds number. Larger values of Reynolds cause a reduction in thermal resistance due to volume friction (\(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\)) of the nanofluid. It can be observed that \(\phi = 3\%\) \({\text{TiO}}_{2}\)/water nanofluid volume friction demonstrated \(16.25\%\) less thermal resistance than water. Physically, the reduction thermal resistance is due to the significantly greater velocity when the Reynolds number is larger. The larger velocity of fluid depresses the thermal resistance among the fluid particles, and larger nanofluids have more heat proficiency. This leads to increased thermal transport, which is inversely proportional to convective thermal resistance.
Friction factor
Figure 17 elucidates the friction factor of nanofluid aspects for \({\text{TiO}}_{2}\)/water nanofluid volume friction (\(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\)) via the Reynolds number. The friction factor of the nanoliquid in the microelectronic six-channel heat sink is reduced by enhancing the Reynolds number. Physically, due to the larger Reynolds number, the velocity is boosted, and the velocity has an opposite relation with the friction factor; therefore, the friction factor of the nanofluid declines with a greater Reynolds number.
Wall temperature
The wall temperature estimations at the bottom side of the heat sink for dissimilar volume friction (\(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\)) of \({\text{TiO}}_{2}\)/water nanofluids in a microelectronic chip with six mini channels via the Reynolds number are shown in Fig. 18. Here, it can be noticed that the wall temperature diminishes via a greater Reynolds number for different volume friction (\(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\)). Figure 19 shows the thermal/temperature contour in the minichannel heat sink for the nanofluid. From the figure, we observed that the wall temperature of the six circular microchannels declines significantly when utilizing coolant. The wall temperature found was \(3546\,\,{\text{K}}\). The largest heat transfer rates are examined for concentration volume friction from 1 to \(3\%\). The outcome depicts that improving the heat transfer coefficient enhances the thermophysical characteristics of the dispersed nanomaterials compared to the host fluid. Thus, \({\text{TiO}}_{2}\) a larger heat efficiency of/water nanoliquids improves heat transfer along the microchannel heat sink.
Pressure drop
The pressure drop across the inlet to outlet face of the six circular microchannel heat sinks from adopting ANSYS-FLUENT is shown in Fig. 20. From the CFD analysis, it can be noticed that the pressure drop is enhanced for each concentration of coolant. Here we acquire \(1996\,\,{\text{Pa}}\) pressure. Figure 21 signifies the pressure drop contour across the inlet to outlet of the six microchannel heat sinks displayed in the cross section utilizing ANSYS-(R19.2) FLUENT. In these figures, we clearly observed two regions with smaller temperature and pressure (blue color) in the inlet of the circular channel heat sink and in the outlet face of the channel greater temperature and pressure drop (red color). Due to the frictional consequences of the nanoparticles and the surface of the channel, the pressure drop increases. Therefore, the pressure drop of the \({\text{TiO}}_{2}\)/water nanoliquid improved with an increase in volumetric concentration friction significance. Here we obtained \(1996\,\,{\text{Pa}}\) pressure.
Wall heat flux
Figure 22 shows the wall heat flux in the microchannel heat sink for each volumetric concentration. The heat flux acts at the underside surface of the microchannel heat sink to compute the heat generation in the microelectronic chip. Here we acquired \(6727\,\,{\text{Wm}}^{ - 2}\) heat flux. Figure 23 clearly shows that the heat flux is clearly applied on the bottom of the microchannels in the electronic chip. We observed that heat flux is increased at each concentration of cooling. The wall heat flux acquired was \(2018\,\,\,{\text{Wm}}^{ - 2}\). The heat flux across the inlet to outlet faces of six circular microchannels; a cross-sectional view is shown in Fig. 24. The heat flux is improved for larger concentrations of coolant. Heat flux has a direct relation with thermal conductivity. Larger heat efficiency was carried out to improve the heat transfer. The \({\text{TiO}}_{2}\)/water nanofluid has high heat transfer across microchannels.
Conclusions
In this study, CFD analysis was conducted to scrutinize the numerical cooling performance of circular minichannel heat sinks with different volume friction (\(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\)) using \({\text{TiO}}_{2}\)/water nanofluids and water for electronic chips. The computational ANSYS-FLUENT (R19.2) Package is used to observe the CFD analysis. The flow governing equations are approached numerically by (FVM) with the ANSYS-FLUENT package. Based on the outcomes, it was observed that a noteworthy increment in the heat transfer coefficient was obtained by using nanofluids as coolants w.r.t water. It is scrutinized that the heat transfer coefficient is escalated by enlarging the inlet velocity. The HTC is improved \(12.09\%\) to \(14.02\%\) with concentration \(\phi = 1\%\), \(\phi = 2\%\) and \(\phi = 3\%\) of nanofluid compared to water. The Nusselt number is amplified via larger estimations of the Reynolds number and volume friction. It is noted that the thermal resistance and friction factor decrease when the nanoparticle concentration increases under the Reynolds number. These effects occur due to the larger thermal efficiency of the nanofluid and random motion of nanoparticles. Nanofluids used in microchannel heat sinks enhance the efficiency of electronic chip cooling compared to distilled water.
References
Saini, M., & Webb, R. L. Heat rejection limits of air cooled plane fin heat sinks for computer cooling. in ITherm 2002. Eighth Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (Cat. No. 02CH37258), 1–8. (IEEE, 2002).
Bahiraei, M. & Heshmatian, S. Efficacy of a novel liquid block working with a nanofluid containing graphene nanoplatelets decorated with silver nanoparticles compared with conventional CPU coolers. Appl. Therm. Eng. 127, 1233–1245 (2017).
Li, J. Computational Analysis of Nanofluid Flow in Microchannels with Applications to Microheat Sinks and Bio-MEMS (Springer, 2008).
Naphon, P. & Nakharintr, L. Heat transfer of nanofluids in the mini-rectangular fin heat sinks. Int. Commun. Heat Mass Transfer 40, 25–31 (2013).
Farsad, E., Abbasi, S. P., Zabihi, M. S. & Sabbaghzadeh, J. Numerical simulation of heat transfer in a micro channel heat sinks using nanofluids. Heat Mass Transf. 47(4), 479–490 (2011).
Saadoon, Z. H., Ali, F. H., & Sheikholeslami, M. Numerical investigation of heat transfer enhancement using (Fe3O4 and Ag-H2O) nanofluids in (converge-diverge) mini-channel heat sinks. Mater. Today Proc. (2021).
Duangthongsuk, W. & Wongwises, S. An experimental investigation on the heat transfer and pressure drop characteristics of nanofluid flowing in microchannel heat sink with multiple zigzag flow channel structures. Exp. Therm. Fluid Sci. 87, 30–39. https://doi.org/10.1016/j.expthermflusci.2017.04.013 (2017).
Hussien, A. A. et al. Numerical study of heat transfer enhancement using Al2O3–graphene/water hybrid nanofluid flow in mini tubes. Iran J. Sci. Technol. Trans. Sci. 43, 1989–2000. https://doi.org/10.1007/s40995-018-0670-1HeatMassTransfer (2019).
Yarmand, H. et al. Graphene nanoplatelets–silver hybrid nanofluids for enhanced heat transfer. Energy Convers. Manag. 100, 419–428. https://doi.org/10.1016/j.enconman.2015.05.023 (2015).
Sakkaki, M. et al. Phase change materials as quenching media for heat treatment of 42CrMo4 steels. J. Cent. South Univ. 27, 752–761. https://doi.org/10.1007/s11771-020-4328-8 (2020).
Bahiraei, M., Naghibzadeh, S. M. & Jamshidmofid, M. Efficacy of an eco-friendly nanofluid in a miniature heat exchanger regarding to arrangement of silver nanoparticles. Energy Convers. Manag. 144, 224–234. https://doi.org/10.1016/j.enconman.2017.04.076 (2017).
Das, S. K., Choi, S. U. S. & Patel, H. E. Heat transfer in nanofluids: A review. Heat Transf. Eng. 27, 3–19. https://doi.org/10.1080/01457630600904593 (2006).
Muhammad, T., Waqas, H., Khan, S. A., Ellahi, R. & Sait, S. M. Significance of nonlinear thermal radiation in 3D Eyring-Powell nanofluid flow with Arrhenius activation energy. J. Therm. Anal. Calorim. 143(2), 929–944 (2021).
Sheikholeslami, M., Bandpy, M. G., Ellahi, R., Hassan, M. & Soleimani, S. Effects of MHD on Cu–water nanofluid flow and heat transfer by means of CVFEM. J. Magn. Magn. Mater. 349, 188–200 (2014).
Wakif, A. et al. Magneto-convection of alumina-water nanofluid within thin horizontal layers using the revised generalized Buongiorno’s model. Front. Heat Mass Transf. (FHMT) 12, 3 (2018).
Khan, U., Bilal, S., Zaib, A., Makinde, O. D. & Wakif, A. Numerical simulation of a nonlinear coupled differential system describing a convective flow of Casson gold–blood nanofluid through a stretched rotating rigid disk in the presence of Lorentz forces and nonlinear thermal radiation. Numer. Methods Partial Diff. Equ. https://doi.org/10.1002/num.22620 (2020).
Yu, X. & Xuan, Y. Investigation on thermo-optical properties of CuO/ag plasmonic nanofluids. Sol. Energy. 160, 200–207 (2018).
Moghadam, A. J., Farzane-Gord, M., Sajadi, M. & Hoseyn-Zadeh, M. Effects of CuO/water nanofluid on the efficiency of a flat-plate solar collector. Exp. Thermal Fluid Sci. 58, 9–14 (2014).
SadiqAl-Baghdadi, M. A. R. A CFD analysis of transport phenomena and electrochemical reactions in a tubular-shaped ambient air-breathing PEM micro fuel cell. Trans. Hong Kong Inst. Eng. 17(2), 1–8 (2010).
Klazly, M. M. & Bognár, G. CFD study for the flow behavior of nanofluid flow over flat plate. Int. J. Mech. 14, 49–57 (2020).
Mohammed, H. I., Giddings, D. & Walker, G. S. CFD simulation of a concentrated salt nanofluid flow boiling in a rectangular tube. Int. J. Heat Mass Transf. 125, 218–228 (2018).
Naphon, P. & Nakharintr, L. Numerical investigation of laminar heat transfer of nanofluid-cooled mini-rectangular fin heat sinks. J. Eng. Phys. Thermophys. 88(3), 666–675 (2015).
Fluent, I. FLUENT 63 User’s Guide (Fluent Inc, 2006).
Ghasemi, S. E., Ranjbar, A. A. & Hosseini, M. J. Experimental evaluation of cooling performance of circular heat sinks for heat dissipation from electronic chips using nanofluid. Mech. Res. Commun. 84, 85–89 (2017).
Ghasemi, S. E., Ranjbar, A. A. & Hosseini, M. J. Thermal and hydrodynamic characteristics of water-based suspensions of Al2O3 nanoparticles in a novel minichannel heat sink. J. Mol. Liq. 230, 550–556 (2017).
Ellerman, P. Calculating Reliability Using FIT & MTTF: Arrhenius HTOL Model. Microsemi corp. MicroNote, 1002. (2012).
Acknowledgements
The authors extend their appreciation to the Deanship of Scientific Research at King Khalid University, Abha, Saudi Arabia for funding this work through research groups program under grant number RGP.2/184/43.
Author information
Authors and Affiliations
Contributions
H.W. and S.A.K. generated the research idea, stated the problem, and wrote the codes to perform the numerical calculations and plot the graphical results. U.F. performed the analysis and verified the numerical results; T.M. supervised the whole work, stated the problem, drafted the manuscript and commented on it. S.Y. and A.A. reviewed the manuscript and contributed to the final version of the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Waqas, H., Khan, S., Farooq, U. et al. Thermal transport analysis of six circular microchannel heat sink using nanofluid. Sci Rep 12, 8035 (2022). https://doi.org/10.1038/s41598-022-11121-y
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-022-11121-y
- Springer Nature Limited
This article is cited by
-
Study on magnetohydrodynamic internal cooling mechanism within an aluminium oxide cutting tool
The International Journal of Advanced Manufacturing Technology (2024)
-
Machine learning methods for modeling nanofluid flows: a comprehensive review with emphasis on compact heat transfer devices for electronic device cooling
Journal of Thermal Analysis and Calorimetry (2024)