Abstract
The aim of the research is to investigate the usability of composites produced using the organic waste from hazelnut and corn processing in the Black Sea Region in constructional applications with regard to mechanical and thermal conduction. Polymer composite test samples were produced to which hazelnut shells, corn stalk, nettle stalk (excl. fibres) and nettle fibres had been added in varying (5, 10, 15, 20%) weights to the polyester matrix. Thermal conductivity coefficients were determined in the context of the thermal properties of composite samples. In addition, mechanical properties were determined by compression strength and a three-point bending test. The physical properties of the wastes were determined via XRD, glass transition temperature, one of the thermal features of the composites that is found via DSC and, lastly, the thermal conductivity and specific heat capacity are determined via a heat flow meter. The effect of organic waste amounts and their chemical and physical features on composites’ mechanical and thermal properties are discussed in this study. The results of the study show that nettle stalk-reinforced composites have a low density and more advantageous features than the other composites tested in terms of their thermal conductivities.
Similar content being viewed by others
Abbreviations
- ASTM:
-
American Society for Testing and Materials
- EN:
-
European Standards
- DSC:
-
Differential scanning calorimetry
- MPa:
-
Megapascal
- XRD:
-
X-ray diffraction
- CrI:
-
Crystallinity index
- Q :
-
Heat flow
- C p :
-
Specific heat capacity
References
Abdou AA, Budaiwi IM, Al-Homoud M (2005) Comparison of thermal conductivity measurement of building insulation materials under various operating temperatures. J Build Phys 29:171–184
Agarwal R, Saxena NS, Sharma KB, Thomas S, Pothan LA (2003) Thermal conduction and diffusion through polyester composites. Indian J Pure Appl Phys 41:448–452
Aslı M, Brachelet F, Chauchoıs A, Antczak E, Defer D (2019) Numerical and experimental investigation of heat and mass transfer with in bio based material. Therm Sci 23(1):23–31. https://doi.org/10.2298/TSCI161019175A
ASTM Standard specification for load bearing concrete masonry units ASTM C90-11b, international (2011)
ASTM Standard Test Method for Flexural Strength and Modulus of Elasticity of Chemical-Resistant Mortars, Grouts, Monolithic Surfacings, and Polymer Concretes. (ASTM C580) American Society for Testing and Materials (ASTM), Annual Book of ASTM Standards, 100 Barr Harbor Drive, West Conshohocken, PA. www.astm.org
Benítez-Guerreroa M, Pérez-Maquedab LA, Artiagac A, SánchezJiménezb PE, Pascual-Cosp J (2017) Structural and chemical characteristics of sisal fiber and its components: effect of washing and grinding. J Nat Fibers 14(1):26–39
Bertoncelj B, Vojisavljević K, Vrabelj M, Barbara Malič B (2015) Thermal properties of polymer-matrix composites reinforced with E-glass fibers. Informacije MIDEM. J Microelectron Electron Compon Mater 45:216–221
Bledzki AK, Gassan J (1999) Composites reinforced with cellulose-based fibres. Prog Polym Sci 24:221–274
Borysiak S (2013) Influence of cellulose polymorphs on the polypropylene crystallization. J Therm Anal Calorim 113(1):281–289
Cerqueiraa EF, BaptistabCARP Mulinari DR (2011) Mechanical behaviour of polypropylene reinforced sugarcane bagasse fibers composites. Procedia Eng 10:2046–2051
Devireddy SBR, Biswas S (2016) Physical and thermal properties of unidirectional banana–jute hybrid fiber-reinforced epoxy composites. J Reinf Plast Compos 35(15):1157–1172. https://doi.org/10.1177/0731684416642877
Dong C, Davies IJ (2012) Flexural properties of macadamia nutshell particle reinforced polyester Composites. Compos Part B 43:2751–2756
Dong Z, Dıng RY, Zheng L, Zhang X, Yu CW (2015) Thermal properties of flax fiber scoured by different methods. Therm Sci 19(3):939–945
Donnell OA, Dweib MA, Wool RP (2004) Natural fibre composites with plant oil-based resin. Compos Sci Tecnol 64:1135–1145
EN 12089 (2013) Thermal insulating products for building applications—determination of bending behaviour. European Standards
EN 826 (2013) Thermal insulating products for building applications—determination of compression behaviour. European Standards
Garcia-Garcia D, Quiles-Carrillo L, Montanes N, Fombuena V, Balart R (2018) Manufacturing and characterization of composite fibreboards with Posidonia oceanica wastes with an environmentally-friendly binder from epoxy resin. Materials (Basel) 11(1):35. https://doi.org/10.3390/ma11010035
Gu J, Zhang Q, DangJ XieC (2012) Thermal conductivity epoxy resin composites filled with boron Nitride. Polym Adv Technol 23:1025–1028
Hancox NL (1981) Fibre composite hybrid materials. Macmillan Publishing Co, New York
Hepworth DG, Hobson RN, Bruce DM, Farrent JW (2000) The use of unretted hemp fibre in composite manufacture. Compos Part A 3:1279–1283
Hossain MF, Shuvo SN, Islam MA (2014) Effect of types of wood on the thermal conductivities of wood saw dust particle reinforced composites. 10th International conference on mechanical engineering. ICME 2013 Procedia Engineering, vol 90, pp 46–51
Hurtado PL, Rouilly A, Vandenbossche V, Raynaud C (2016) A review on the properties of cellulose fibre insulation. Build Environ 96:170–177
Jonoobi M, Harun J, Tahir P, Zaini L, SaifluAzry S, Makinejad M (2010) Characteristics of nanofibers extracted from kenaf core. BioResources 5(4):2556–2566
Kittel C (2005) Introduction to solid state physics, 8th ed. Uno R, Tsuya N, Niizeki K et al (eds) Maruzen, Tokyo, John Wiley & Sons, New York
Korkmaz N, Çakmak E, Dayık M (2016) Dokuma karbon elyaf takviyeli karbon nano tüp-epoksikompozit malzemelerin mekanik ve termal karakterizasyonu. Süleyman Demirel Üniversitesi Fen Bilimleri Enstitüsü Dergisi 20(2):338–353
Kumara R, Kumarb K, Sahooc P, Bhowmika S (2014) Study of mechanical properties of wood dust reinforced epoxy composite. 3rd International conference on materials processing and characterisation (ICMPC 2014). Procedia Materials Science, vol 6, pp 551–556
Low IM, McGrath M, Lawrence D, Schmidt P, Lane J, Latella BA, Sim KS (2007) Mechanical and fracture properties of cellulose-fibre-reinforced epoxy laminates. Compos Part A 38:963–974
Mishra S, Tripathy SS, Misra M, Mohanty AK, Nayak SK (2002) Novel eco-friendly biocomposites: biofibre reinforced biodegradable polyester amide composites—fabrication and properties evaluation. J Reinf Plast Compos 21:55–70
Mohanty AK, Misra M, Drzal LT (2001) Surface modifications of natural fibres and performance of the resulting biocomposites: an overview. Compos Interfaces 8:313–343
Mohapatra RC, Mıshrab A, Choudhury BB (2017) Determınatıon of thermal conductivity of pine wood dust filled epoxy composites. Therm Sci 21(1A):199–210
Mwaikambo LY, Ansell MP (2002) Chemical modification of hemp, sisal, jute, and kapok fibres by Alkalisation. J Appl Polym Sci 84:2222–2234
Nan CW, Birringer R, Clarke DR, Gleiter H (1997) Effective thermal conductivity of particulate composites with interfacial thermal resistance. J Appl Phys 81(10):6692–6699
Peng Y, Wu S (2010) The structural and thermal characteristics of wheat straw hemicellulose. J Anal Appl Pyrol 88:134–139
Poliya (2017). https://www.poliya.com/tr/dokum-tipi
Rasat MSM, Wahab R, Sulaiman O, Moktar J, Mohamed A, Tabet TA, Khalid İ (2011) Properties of composite boards from oil palm frond agricultural waste. BioResources 6(4):4389–4403
Sawpan MA, Pickering KL, Fernyhough A (2012) Flexural properties of hemp fibre reinforced polylactide and unsaturated polyester composites. Compos A Appl Sci Manuf 43(3):519–526
Segal L, Creely JJ, Martin AE, Conrad CM (1959) An empirical method for estimating the degree of crystallinity of native cellulose using the X-ray diffractometer. Text Res J 29(10):786–794
Shibata S, Cao Y, Isao Fukumoto I (2005) Effect of bagasse fiber on the flexural properties of biodegradable composites. Polym Compos 26(5):689–694
Stark NM, Berger MJ (1997) Effect of particle size on properties of wood-flour reinforced polypropylene composites. Fourth international conference on woodfiber-plastic composites: May 12–14, the Madison, Wisconsin
Tajvidi M, Falk RH, Hermanson JC (2006) Effect of natural fibers on thermal and mechanical properties of natural fiber polypropylene composites studied by dynamic mechanical analysis. J Appl Polym Sci 101:4341–4349
Teja MS, Ramana MV, Sriramulu D, Rao CJ (2016) Experimental investigation of mechanical and thermal properties of sisal fibre reinforced composite and effect of SiC filler material. IOP Conf. Series: Materials Science and Engineering, 149, 012095. https://doi.org/10.1088/1757-899x/149/1/012095
Teng H (2010) Stiffness properties of particulate composites containing debonded particles. Int J Solids Struct 47:2191–2200
Tian M, Qu L, Zhang X (2014) Enhanced mechanical and thermal properties of regenerated cellulose/graphene composite fibers. Carbohydr Polym 111:456–462
Tutuş A, Çıçekler M, Özkan HG (2017) Fireproof paper production from Turkish red pine (Pinus brutia Ten.) using fire retardants. Kastamonu Uni., Orman Fakültesi Dergisi. J For Fac 17(2):275–281. https://doi.org/10.17475/kastorman.285252
Venkatram B, Kailasanathan C, Seenikannan P, Paramasamy S (2016) Study on the evaluation of mechanical and thermal properties of natural sisal fiber/general polymer composites reinforced with nanoclay, I. J Poly Anal Charact 21(7):647–656
Wakili KG, Binder B, Vonbank R (2003) A simple method to determine the specific heat capacity of thermal insulations used in building construction. Energy Build 35:413–415
Wypych G (2012) Effect of plasticizers on properties of plasticized materials. In: Wypych G (ed) Handbook of plasticizers, 2nd edn. ChemTec Publishing, Toronto, pp 193–272
Author information
Authors and Affiliations
Corresponding author
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
About this article
Cite this article
Büyükkaya, K., Güler, B. & Koru, M. Investigation of the Thermal and Mechanical Properties of Organic Waste Reinforced Polyester Composites. Iran J Sci Technol Trans Civ Eng 45, 757–766 (2021). https://doi.org/10.1007/s40996-020-00517-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40996-020-00517-3