Abstract
A Nd:YAG laser welding technique with varying pulse widths was employed to weld Ti-27 at.% Nb shape memory alloy plates, and subsequent phase transformation characteristics and microhardness of welds were systematically investigated. From microstructure observation, it is apparent that weld seams contain a columnar growth with the low pulse and transferred into a combined growth of columnar and planar with the high pulse width. Moreover, grains in the weld zone exhibited a finer size when compared to the unwelded zone. A small amount of NbTi4 was also found in the welds. In the forward transformation, transformation temperatures did not exhibit peaks, indicating the same behaviour as the original TiNb alloy. Microhardness of the TiNb welds increased as the pulse width increased when compared to the original TiNb alloy. However, little reduction in hardness occurred after a pulse width of 5 ms.
Similar content being viewed by others
References
Baxevanis T, Lagoudas DC (2015) Fracture mechanics of shape memory alloys: review and perspectives. Int J Fract 191:191–213. doi:10.1007/s10704-015-9999-z
Wang L, Lu W, Qin J, et al. (2010) The characterization of shape memory effect for low elastic modulus biomedical β-type titanium alloy. Mater Charact 61:535–541. doi:10.1016/j.matchar.2010.02.009
Rondelli G (1996) Corrosion resistance tests on NiTi shape memory alloy. Biomaterials 17:2003–2008. doi:10.1016/0142-9612(95)00352-5
Geurtsen W (2002) Biocompatibility of dental casting alloys. Crit Rev Oral Biol Med 13:71–84. doi:10.1177/154411130201300108
Pulletikurthi C, Munroe N, Gill P, et al. (2011) Cytotoxicity of Ni from surface-treated porous nitinol (PNT) on osteoblast cells. J Mater Eng Perform 20:824–829. doi:10.1007/s11665-011-9930-3
Michiardi A, Aparicio C, Planell JA, Gil FJ (2006) New oxidation treatment of NiTi shape memory alloys to obtain Ni-free surfaces and to improve biocompatibility. J Biomed Mater Res - Part B Appl Biomater 77:249–256. doi:10.1002/jbm.b.30441
Ping DH, Cui CY, Yin FX, Yamabe-Mitarai Y (2006) TEM investigations on martensite in a Ti-Nb-based shape memory alloy. Scr Mater 54:1305–1310. doi:10.1016/j.scriptamat.2005.12.022
Cremasco A, Andrade PN, Contieri RJ, et al. (2011) Correlations between aging heat treatment, ω phase precipitation and mechanical properties of a cast Ti–Nb alloy. Mater Des 32:2387–2390
Kim JI, Kim HY, Inamura T, et al. (2005) Shape memory characteristics of Ti-22Nb-(2-8)Zr(at.%) biomedical alloys. Mater Sci Eng A 403:334–339. doi:10.1016/j.msea.2005.05.050
Baker C (1971) The shape-memory effect in a titanium-35 wt.-% niobium alloy. Met Sci 5:92–100. doi:10.1179/030634571790439658
Al-Zain Y, Kim HY, Hosoda H, et al. (2010) Shape memory properties of Ti-Nb-Mo biomedical alloys. Acta Mater 58:4212–4223. doi:10.1016/j.actamat.2010.04.013
Wen M, Wen C, Hodgson P, Li Y (2014) Fabrication of Ti-Nb-Ag alloy via powder metallurgy for biomedical applications. Mater Des 56:629–634. doi:10.1016/j.matdes.2013.11.066
Farooq MU, Khalid FA, Zaigham H, Abidi IH (2014) Superelastic behaviour of Ti-Nb-Al ternary shape memory alloys for biomedical applications. Mater Lett 121:58–61. doi:10.1016/j.matlet.2014.01.148
Fukui Y, Inamura T, Hosoda H, et al. (2004) Mechanical properties of a Ti-Nb-Al shape memory alloy. Mater Trans 45:1077–1082. doi:10.2320/matertrans.45.1077
Hassan MR, Mehrpouya M, Dawood S (2014) Review of the machining difficulties of nickel-titanium based shape memory alloys. 564:533–537. doi: 10.4028/www.scientific.net/AMM.564.533
Weinert K, Petzoldt V (2004) Machining of NiTi based shape memory alloys. Mater Sci Eng A 378:180–184. doi:10.1016/j.msea.2003.10.344
Eijk Van Der C, Fostervoll H, Sallom ZK, Akselsen OM (2003) Plasma welding of NiTi to NiTi, stainless steel and hastelloy C276. Solutions 13–15.
Delobelle V, Delobelle P, Liu Y, et al. (2013) Resistance welding of NiTi shape memory alloy tubes. J Mater Process Technol 213:1139–1145. doi:10.1016/j.jmatprotec.2013.01.013
Shinoda T, Owa T, Magula V (1999) Microstructural analysis of friction welded joints in TiNi alloy microstructural analysis of friction welded joints in TiNi alloy. Weld Int 13:180–18541. doi:10.1080/09507119909447361
Shiue RH, Wu SK (2006) Infrared brazing of Ti50Ni50 shape memory alloy using two Ag–Cu–Ti active braze alloys. Intermetallics 14:630–638. doi:10.1016/j.intermet.2005.10.012
van der Eijk C, Sallom ZK, Akselsen OM (2008) Microwave brazing of NiTi shape memory alloy with Ag–Ti and Ag–Cu–Ti alloys. Scr Mater 58:779–781. doi:10.1016/j.scriptamat.2007.12.017
Hahnlen R, Fox G, Dapino M (2012) Ultrasonic soldering of shape memory NiTi to aluminum 2024. Weld J 91:1–7
Yang D, Jiang HC, Zhao MJ, Rong LJ (2014) Microstructure and mechanical behaviors of electron beam welded NiTi shape memory alloys. Mater Des 57:21–25. doi:10.1016/j.matdes.2013.12.039
Oliveira JP, Barbosa D, Fernandes FMB, Miranda RM (2016) Tungsten inert gas ( TIG ) welding of Ni-rich NiTi plates : functional behavior. Smart Mater Struct 25:03LT01. doi:10.1088/0964-1726/25/3/03LT01
Oliveira JP, Miranda RM, Schell N, Fernandes FMB (2016) High strain and long duration cycling behavior of laser welded NiTi sheets. Int J Fatigue 83:195–200. doi:10.1016/j.ijfatigue.2015.10.013
Oliveira JP, Panton B, Zeng Z, et al. (2016) Laser welded superelastic Cu-Al-Mn shape memory alloy wires. Mater Des 90:122–128. doi:10.1016/j.matdes.2015.10.125
Fukumoto S, Inoue T, Mizuno S, et al. (2010) Friction welding of TiNi alloy to stainless steel using Ni interlayer. Sci Technol Weld Join 15:124–130. doi:10.1179/136217109X12577814486692
Li H, Sun D, Cai X, et al. (2013) Laser welding of TiNi shape memory alloy and stainless steel using Co filler metal. Opt Laser Technol 45:453–460. doi:10.1016/j.optlastec.2012.06.010
GONG W, CHEN Y, KE L (2011) Microstructure and properties of laser micro welded joint of TiNi shape memory alloy. Trans Nonferrous Met Soc China 21:2044–2048. doi:10.1016/S1003-6326(11)60970-9
Chan CW, Man HC (2011) Laser welding of thin foil nickeltitanium shape memory alloy. Opt Lasers Eng 49:121–126. doi:10.1016/j.optlaseng.2010.08.007
Kobayashi S, Nakagawa S, Nakai K, Ohmori Y (2002) Phase decomposition in a Ti-13Nb-13Zr alloy during aging at 600. DEG. C. Mater Trans 43:2956–2963
Acknowledgments
The authors would like to thank the Ministry of Higher Education of Malaysia and Universiti Teknologi Malaysia for providing the financial support under the University Research Grant No. Q.J130000.3024.00M57 and research facilities.
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended for publication by Commission IV - Power Beam Processes
Rights and permissions
About this article
Cite this article
Bahador, A., Saud, S.N., Hamzah, E. et al. Nd:YAG laser welding of Ti-27 at.% Nb shape memory alloys. Weld World 60, 1133–1139 (2016). https://doi.org/10.1007/s40194-016-0375-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40194-016-0375-z