Skip to main content
SpringerLink
Log in

Influence of weld quality on the fatigue strength of thin normal and high strength steel butt joints

  • Research Paper
  • Published:
Welding in the World Aims and scope Submit manuscript

Abstract

For building more energy-efficient and eco-friendly structures, new lightweight solutions are needed. Utilization of higher strength steels and smaller plate thicknesses together with modern welding technologies holds a huge potential for weight reduction. However, due to lack of knowledge about the fatigue resistance, current rules do not allow using smaller plate thicknesses than 5 mm nor benefiting from higher strength steels in large welded structures such as in ships. One of the main concerns in addition to larger welding-induced distortions is the weld quality. This paper compares the fatigue strength of 4 mm thick normal and high strength steel butt joints produced by different welding methods leading to different weld shape and quality. In order to eliminate the effect of secondary bending due to initial distortions and bring out the influence of weld quality, the fatigue test results are analyzed using structural hot spot stress approach with measured specimen geometries. The results show considerable yield-limit-dependent increase in the fatigue strength of high quality welds, while no benefit from higher base material strength was observed for low quality butt joints. In addition, the suitability of existing weld quality recommendations for thin welded joints was evaluated and future research needs discussed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15

Similar content being viewed by others

References

  1. Det Norske Veritas, Fatigue assessment of ship structures, Classification Notes 30.7 (2014)

  2. Hobbacher, A., Recommendations for fatigue design of welded joints and components, IIW doc. 1823–07, Welding Research Coiuncil Bulletin 520, New York (2009)

  3. Lillemäe I, Lammi H, Molter L, Remes H (2012) Fatigue strength of welded butt joints in thin and slender specimens. Int J Fatigue 44:98–106

    Article  Google Scholar 

  4. Eggert, L., Fricke, W., Paetzhold, H., (2012) Fatigue strength of thin-plated block joints with typical shipbuilding imperfections. Welding in the World 56(11):119–128

  5. Fricke W, Remes H, Feltz O, Lillemäe I, Tchuindjang D, Reinert T, Nevierov A, Sichermann W, Brinkmann M, Kontkanen T, Bohlmann B, Molter L (2015) Fatigue strength of laser-welded thin-plate ship structures based on nominal and structural hot-spot stress approach. Ships Offshore Struct 10(1):39–44

    Article  Google Scholar 

  6. Fricke W, Feltz O (2013) Consideration of influence factors between small-scale specimens and large components on the fatigue strength of thin-plated block joints in shipbuilding. Fatigue Fract Eng Mater Struct 36(12):1223–1231

    Article  Google Scholar 

  7. Ahiale GK, Oh Y-J (2014) Microstructure and fatigue performance of butt-welded joints in advanced high-strength steels. Mater Sci Eng A 597:342–348

    Article  Google Scholar 

  8. Remes H, Fricke W (2014) Influencing factors on fatigue strength of welded thin plates based on structural stress assessment. Weld World 58(6):915–923

    Article  Google Scholar 

  9. Stein, J., Kallage, P., Induction assisted welding technologies in steel utilization – INDUCWELD, RFSR-CT-2005-00040, Res. Prog. Fund for Coal and Steel (2010)

  10. Costa JDM, Ferreira JAM, Abreu LPM (2010) Fatigue behavior of butt welded joints in a high strength steel. Procedia Eng 2:697–705

    Article  Google Scholar 

  11. Remes, H., Peltonen, M., Seppänen, T., Kukkonen, A., Liinalampi, S., Lillemäe, I., Lehto, P., Hänninen, H., Romanoff, J., Nummela, S., Fatigue strength of welded extra high-strength and thin steel plates based on nominal and structural hot-spot stress approaches, Proceedings of 5th International Conference on Marine Structures MARSTRUCT 2015, Southampton, UK, pp. 301–307

  12. Radaj D (1990) Design and analysis of fatigue resistant welded structures. Abington Publishing, Woodhead Publishing Ltd, Cambridge, England

    Book  Google Scholar 

  13. IACS Shipbuilding and Repair Quality Standard, Revision 6 (2012)

  14. ISO 13919–1 Welding – Electron and laser-beam welded joints – Guidance on quality levels for imperfections – Part 1: Steel (1996)

  15. ISO 5817:2014 Welding – Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) – Quality levels for imperfections (2014)

  16. Jonsson B, Samuelsson J, Marquis G (2011) Development of weld quality criteria based on fatigue performance. Weld World 55(11–12):79–88

    Article  Google Scholar 

  17. Lawrence FV, Ho NJ, Mazumdar PK (1981) Predicting the fatigue resistance of welds. Ann Rev Mater Sci 11:401–425

    Article  Google Scholar 

  18. Remes H, Varsta P (2010) Statistics of weld geometry for laser-hybrid welded joints and its application within notch stress approach. Weld World 54(7):R189–R207

    Article  Google Scholar 

  19. Abramowitz, M., Stegun, I.A., Handbook of Mathematical Functions with Formulas, Graphs, and Mathematical Tables, Dover, Ninth printing, Table 25.2 (1970)

  20. Hobbacher, A., Kassner, M., On relation between fatigue properties of welded joints and quality groups in ISO 5817, IIW document XIII-2323-10 (2010)

  21. Sonsino CM, Bruder T, Baumgartner J (2010) S-N lines for welded thin joints—suggested slopes and FAT-values for applying the notch stress concept with various reference radii, Welding in the World, 54, Issue 11–12

    Google Scholar 

  22. Liinalampi S, Remes H, Lehto P, Lillemäe I, Romanoff J, Porter D (2016) Fatigue strength analysis of laser-hybrid welds in thin plate considering weld geometry in microscale. Int J Fatigue. doi:10.1016/j.ijfatigue.2016.01.019

    Google Scholar 

Download references

Acknowledgments

The research presented in this paper has received funding from TEKES, the Technology Agency of Finland. The work is part of the Future Digital Manufacturing Technologies (MANU) and Breakthrough Steels and Applications (BSA) projects within the scope of Finnish Metals and Engineering Competence Center (FIMECC). The financial support is gratefully appreciated.

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Aalto University School of Engineering, P.O. Box 12200, FIN-00076, Aalto, Finland

    I. Lillemäe, H. Remes & S. Liinalampi

  2. Meyer Turku Oy, FI-20101, Turku, Finland

    Antti Itävuo

Authors
  1. I. Lillemäe
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. H. Remes
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. Liinalampi
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Antti Itävuo
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to I. Lillemäe.

Additional information

Recommended for publication by Commission XIII - Fatigue of Welded components and Structures

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Lillemäe, I., Remes, H., Liinalampi, S. et al. Influence of weld quality on the fatigue strength of thin normal and high strength steel butt joints. Weld World 60, 731–740 (2016). https://doi.org/10.1007/s40194-016-0326-8

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40194-016-0326-8

Keywords (IIW Thesaurus)

Search

Navigation