Skip to main content
SpringerLink
Log in

Experimental Investigations on Microstructure, Mechanical Behavior and Tribological analysis of AA5154/SiC Composites by Stir Casting

  • Original Paper
  • Published:
Silicon Aims and scope Submit manuscript

Abstract

Aluminum metal matrix composites (MMCs) exhibit promising mechanical properties that are potential materials for the aeronautical and automotive industries. In this study, aluminum-magnesium base alloy i.e. 5154 based composites reinforced with silicon carbide (SiC) particles were fabricated by the stir casting process. The mechanical properties such as tensile strength, impact strength, and micro-hardness were evaluated. The microstructural analysis was studied using field emission scanning electron microscopy and X-ray diffraction analysis. With uniform dispersion and good interfacial bonding between the aluminum and silicon carbide, the mechanical properties were found to be enhanced significantly. The 15wt% SiC reinforced composites exhibited a maximum enhancement of 37 % in the hardness, 35 % in the tensile strength. The impact strength was found to be reduced by a maximum of 37 % when compared with the base aluminum alloy showing the loss in ductility. Furthermore, the sliding wear behavior of the SiC reinforced composites was also studied. The wear rate during the test was found to be decreased with sliding distance whereas an increase in the applied load resulted in a higher wear rate. At 2000 m of sliding distance, the wear rate of 15wt% SiC composite was reduced by 51 % as compared to base alloy at an applied load 10 N whereas, at 30 N of applied load, the wear rate was reduced by 66 %. A reduction in the volumetric wear loss of the composites was observed as compared to the base alloy indicating an enhancement in the wear resistance of the composites.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

Data Availability

All data generated and analyzed in this study are included in the article.

References

  1. Singh AK, Soni S, Rana RS (2020) A critical review on synthesis of aluminum metallic composites through stir casting: challenges and opportunities. Adv Eng Mater 22(10):2000322. https://doi.org/10.1002/adem.202000322

    Article  CAS  Google Scholar 

  2. Samal P, Vundavilli PR, Meher A, Mahapatra MM (2020) Recent progress in aluminum metal matrix composites: a review on processing, mechanical and wear properties. J Manuf Process 59:131–152. https://doi.org/10.1016/j.jmapro.2020.09.010

    Article  Google Scholar 

  3. Sakthivelu S, Sethusundaram PP, Ravichandran M, Meignanamoorthy M (2020) Experimental investigation and analysis of properties and dry sliding wear behavior of Al-Fe-Si alloy matrix composites. Silicon. https://doi.org/10.1007/s12633-020-00662-4

    Article  Google Scholar 

  4. Samal P, Vundavilli PR, Meher A, Mahapatra MM (2019) Influence of TiC on dry sliding wear and mechanical properties of in situ synthesized AA5052 metal matrix composites. J Compos Mater 53(28–30):4323–4336. https://doi.org/10.1177/0021998319857124

    Article  CAS  Google Scholar 

  5. Pan S, Saso T, Yu N, Sokoluk M, Yao G, Umehara N, Li X (2020) New study on tribological performance of AA7075-TiB2 nanocomposites. Tribol Int 152:106565. https://doi.org/10.1016/j.triboint.2020.106565

    Article  CAS  Google Scholar 

  6. Zhu J, Jiang W, Li G, Guan F, Yu Y, Fan Z (2020) Microstructure and mechanical properties of SiCnp/Al6082 aluminum matrix composites prepared by squeeze casting combined with stir casting. J Mater Process Technol 283:116699. https://doi.org/10.1016/j.jmatprotec.2020.116699

    Article  CAS  Google Scholar 

  7. Jojith R, Radhika N (2020) Investigation of mechanical and tribological behaviour of heat-treated functionally graded Al-7Si/B4C composite. Silicon 12(9):2073–2085. https://doi.org/10.1007/s12633-019-00294-3

    Article  CAS  Google Scholar 

  8. Bhoi NK, Singh H, Pratap S (2020) Developments in the aluminum metal matrix composites reinforced by micro/nano particles – a review. J Compos Mater 54(6):813–833. https://doi.org/10.1177/0021998319865307

    Article  CAS  Google Scholar 

  9. Arunachalam R, Kumar P, Muraliraja RA (2019) Review on the production of metal matrix composites through stir casting – furnace design, properties, challenges, and research opportunities. J Manuf Process 42:213–245. https://doi.org/10.1016/j.jmapro.2019.04.017

    Article  Google Scholar 

  10. Samal P, Vundavilli PR, Meher A, Mahapatra MM (2019) Fabrication and mechanical properties of titanium carbide reinforced aluminium composites. Mater Today Proc 18(7):2649–2655. https://doi.org/10.1016/j.matpr.2019.07.125

    Article  CAS  Google Scholar 

  11. Fenghong C, Chang C, Zhenyu W, Muthuramalingam T, Anbuchezhiyan G (2019) Effects of silicon carbide and tungsten carbide in aluminium metal matrix composites. Silicon 11(6):2625–2632. https://doi.org/10.1007/s12633-018-0051-6

    Article  CAS  Google Scholar 

  12. Bandil K, Vashisth H, Kumar S, Verma L, Jamwal A, Kumar D, Singh N, Sadasivuni KK, Gupta P (2019) Microstructural, mechanical and corrosion behaviour of Al–Si alloy reinforced with SiC metal matrix composite. J Compos Mater 53(28–30):4215–4223. https://doi.org/10.1177/0021998319856679

    Article  CAS  Google Scholar 

  13. Samal P, Mandava RK, Vundavilli PR (2020) Dry sliding wear behavior of Al 6082 metal matrix composites reinforced with red mud particles. SN Appl Sci 2(2):313. https://doi.org/10.1007/s42452-020-2136-2

    Article  CAS  Google Scholar 

  14. Yaghobizadeh O, Baharvandi HR, Ahmadi AR, Aghaei E (2019) Development of the properties of Al/SiC nano-composite fabricated by stir cast method by means of coating SiC particles with Al. Silicon 11(2):643–649. https://doi.org/10.1007/s12633-018-9867-3

    Article  CAS  Google Scholar 

  15. Du X, Gao T, Liu G, Liu X (2017) In situ synthesizing SiC particles and its strengthening effect on an Al–Si–Cu–Ni–Mg piston alloy. J Alloys Compd 695:1–8. https://doi.org/10.1016/j.jallcom.2016.10.170

    Article  CAS  Google Scholar 

  16. Zheng KL, Wei XS, Yan B, Yan PF (2020) Ceramic waste SiC particle-reinforced Al matrix composite brake materials with a high friction coefficient. Wear 458–459:203424. https://doi.org/10.1016/j.wear.2020.203424

    Article  CAS  Google Scholar 

  17. Novich KA, Pedersen SV, Borrelli RA, Christensen R, Jaques BJ (2021) Synthesis of boron carbide reinforced aluminum castings through mechanical stir casting. J Compos Mater :1–13. https://doi.org/10.1177/0021998320987597

  18. Wang W, Du A, Fan Y, Zhao X, Wang X, Ma R, Li Q (2018) Microstructure and tribological properties of SiC matrix composites infiltrated with an aluminium alloy. Tribol Int 120:369–375. https://doi.org/10.1016/j.triboint.2018.01.001

    Article  CAS  Google Scholar 

  19. Rao TB (2018) An experimental investigation on mechanical and wear properties of Al7075/SiCp composites: effect of SiC content and particle size. ASME J Tribol 140:031601. https://doi.org/10.1115/1.4037845

    Article  CAS  Google Scholar 

  20. Smirnov AS, Shveikin VP, Smirnova EO, Belozerov GA, Konovalov AV, Vichuzhanin DI, Muizemnek OY (2018) Effect of silicon carbide particles on the mechanical and plastic properties of the AlMg6/10 % SiC metal matrix composite. J Compos Mater 52(24):3351–3363. https://doi.org/10.1177/0021998318765622

    Article  CAS  Google Scholar 

  21. Singh RK, Telang A, Das S, Microstructure (2020) Mechanical properties and two-body abrasive wear behaviour of hypereutectic Al—Si—SiC composite. Trans Nonferrous Met Soc China (Engl Ed) 30:65–75. https://doi.org/10.1016/S1003-6326(19)65180-0

    Article  CAS  Google Scholar 

  22. Khan MM, Dixit G (2020) Evaluation of microstructure, mechanical, thermal and erosive wear behavior of aluminum-based composites. Silicon 12:59–70. https://doi.org/10.1007/s12633-019-00099-4

    Article  CAS  Google Scholar 

  23. Samal P, Babu DM, Kiran SV, Surekha B, Vundavilli PR, Mandal A (2020) Study of microstructural and machining characteristics of hypereutectic Al-Si alloys using wire-EDM for photovoltaic application. Silicon :1–13. https://doi.org/10.1007/s12633-020-00742-5

  24. Hillary JJM, Ramamoorthi R, Joseph JDJ, Samuel CSJA (2020) Study on microstructural effect and mechanical behaviour of Al6061-5 % SiC-TiB2 particulates reinforced hybrid metal matrix composites. J Compos Mater 54(17):2327–2337. https://doi.org/10.1177/0021998319894666

    Article  CAS  Google Scholar 

  25. Ravikumar K, Kiran K, Sreebalaji VS (2017) Characterization of mechanical properties of aluminium/tungsten carbide composites. Measurement 102:142–149. https://doi.org/10.1016/j.measurement.2017.01.045

    Article  Google Scholar 

  26. Kim CS, Cho K, Manjili MH, Nezafati M (2017) Mechanical performance of particulate-reinforced Al Metal-Matrix Composites (MMCs) and Al Metal-Matrix Nano-Composites (MMNCs). J Mater Sci 52:13319–13349. https://doi.org/10.1007/s10853-017-1378-x

    Article  CAS  Google Scholar 

  27. Samal P, Vundavilli PR (2019) Investigation of impact performance of aluminum metal matrix composites by stir casting. IOP Conf Ser Mater Sci Eng 653:012047. https://doi.org/10.1088/1757-899X/653/1/012047

    Article  CAS  Google Scholar 

  28. Ravi Kumar K, Kiran K, Sreebalaji VS (2017) Micro structural characteristics and mechanical behaviour of aluminium matrix composites reinforced with titanium carbide. J Alloys Compd 723:795–801. https://doi.org/10.1016/j.jallcom.2017.06.309

    Article  CAS  Google Scholar 

  29. Zhang Z, Chen DL (2008) Contribution of orowan strengthening effect in particulate-reinforced metal matrix nanocomposites. Mater Sci Eng A 484:148–152. https://doi.org/10.1016/j.msea.2006.10.184

    Article  CAS  Google Scholar 

  30. Dey D, Bhowmik A, Biswas A (2020) Effect of SiC content on mechanical and tribological properties of Al2024-SiC composites. Silicon. https://doi.org/10.1007/s12633-020-00757-y

    Article  Google Scholar 

  31. Rao TB, Microstructural (2021) Mechanical, and wear properties characterization and strengthening mechanisms of Al7075/SiCnp composites processed through ultrasonic cavitation assisted stir-casting. Mater Sci Eng A 805:140553. https://doi.org/10.1016/j.msea.2020.140553

    Article  CAS  Google Scholar 

  32. Kumar N, Gautam G, Gautam RK, Mohan A, Mohan SA (2017) Study on Mechanical properties and strengthening mechanisms of AA5052/ZrB2 in situ composites. J Eng Mater Technol 139(1):011002–011001. https://doi.org/10.1115/1.4034692

    Article  CAS  Google Scholar 

  33. Sujith SV, Mahapatra MM, Mulik RS (2019) An investigation into fabrication and characterization of direct reaction synthesized Al-7079-TiC in situ metal matrix composites. Arch Civ Mech Eng 19:63–78. https://doi.org/10.1016/j.acme.2018.09.002

    Article  Google Scholar 

  34. Radhika N, Raghu R (2017) Characterization of mechanical properties and three-body abrasive wear of functionally graded aluminum LM25/titanium carbide metal matrix composite. Mater Sci Eng Technol 48(9):882–892. https://doi.org/10.1002/mawe.201700559

    Article  CAS  Google Scholar 

  35. Meher A, Mahapatra MM, Samal P, Vundavilli PR (2020) Abrasive wear behaviour of TiB2 reinforced in–situ synthesized magnesium RZ5 alloy based metal matrix composites. Met Mater Int :1–14. https://doi.org/10.1007/s12540-020-00746-1

  36. Gowrishankar TP, Manjunatha LH, Sangmesh B (2020) Mechanical and wear behaviour of Al6061 reinforced with graphite and TiC hybrid MMC’s. Mater Res Innov 24(3):179–185. https://doi.org/10.1080/14328917.2019.1628497

    Article  CAS  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. School of Mechanical Sciences, Indian Institute of Technology Bhubaneswar, Argul, 752050, India

    Priyaranjan Samal & Pandu R. Vundavilli

  2. School of Mechanical Engineering, KIIT University, Bhubaneswar, 751024, India

    B. Surekha

Authors
  1. Priyaranjan Samal
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. B. Surekha
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Pandu R. Vundavilli
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

Priyaranjan Samal: Conceptualization and Experimentation, Result & Analysis.

Dr. B. Surekha: Experimentation and Analysis.

Dr. Pandu R. Vundavilli: Supervision and final draft of the manuscript.

Corresponding author

Correspondence to Priyaranjan Samal.

Ethics declarations

The research was carried out in accordance with all ethical standards.

Consent to Participate

The authors give full consent to participate in this research work.

Consent for Publication

The authors give full consent for the publication of this research work.

Conflict of Interest

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Additional information

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Samal, P., Surekha, B. & Vundavilli, P.R. Experimental Investigations on Microstructure, Mechanical Behavior and Tribological analysis of AA5154/SiC Composites by Stir Casting. Silicon 14, 3317–3328 (2022). https://doi.org/10.1007/s12633-021-01115-2

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12633-021-01115-2

Keywords

Search

Navigation