Abstract
This paper mainly concerns the thermo-mechanical analysis to evaluate the process parameters in the hot press forming with the 22MnB5 sheet such as the austenitization temperature, transport and quenching time for enhancing the efficiency in the production cycle. It is noted that the transport time is most influencing process parameter in the hot press forming to increase production efficiency without sacrificing the strength of the final product. In addition, we newly proposed a scheme to reproduce the flow curves of the hot stamped 22MnB5 sheet with respect to the martensite fraction by correlating the numerical analyses and tensile test results. To take into consideration of the strength variation in the hot stamped door impact beam, entire part is partitioned into several domains on which adaptive flow curves are assigned with respect to the martensite fraction. It demonstrates a good agreement with experimental 3-point bending test with the hot stamped door impact beam when applying the proposed method adopting adaptive flow curves with respect to the martensite fraction.
Similar content being viewed by others
References
AutoFormplusR7 (2016). 0.2 Software Manual.
Bok, H. H., Kim, S. N., Suh, D. W., Barlat, F. and Lee, M. G. (2015). Non-isothermal kinetics model to predict accurate phase transformation and hardness of 22MnB5 boron steel. Materials Science and Engineering: A, 626, 67–73.
Barcellona, A. and Palmeri, D. (2009). Effect of plastic hot deformation on the hardness and continuous cooling transformations of 22MnB5 microalloyed boron steel. Metallurgical and Materials Trans. A 40, 5, 1160–1174.
Bardelcik, A., Worswick, M. J., Winkler, S. and Wells, M. A. (2012). A strain rate sensitive constitutive model for quenched boron steel with tailored properties. Int. J. Impact Engineering, 50, 49–62.
Cai, J. (2011). Modelling of Phase Transformation in Hot Stamping of Boron Steel. Ph. D. Dissertation. Imperial College London. London, UK.
Caron, E. J., Daun, K. J. and Wells, M. A. (2014). Experimental heat transfer coefficient measurements during hot forming die quenching of boron steel at high temperatures. Int. J. Heat and Mass Transfer, 71, 396–404.
Cui, J., Sun, G., Xu, J., Huang, X. and Li, G. (2015). A method to evaluate the formability of high-strength steel in hot stamping. Materials & Design, 77, 95–109.
Cui, J., Lei, C., Xing, Z. and Li, C. (2012). Microstructure distribution and mechanical properties prediction of boron alloy during hot forming using FE simulation. Materials Science and Engineering: A, 535, 241–251.
Choi, W. S. and De Cooman, B. C. (2014). Characterization of the bendability of press-hardened 22MnB5 steel. Steel Research Int. 85, 5, 824–835.
Denis, S., Gautier, E., Simon, A. and Beck, G. (1985). Stress phase transformation interactions-basic principles, modelling, and calculation of internal stresses. Materials Science and Technology 1, 10, 805–814.
Escher, C. and Wilzer, J. (2015). Tool steels for hot stamping of high strength automotive body parts. Int. Conf. Stone and Concrete Machining (ICSCM), Bochum, Germany, 219–228.
Fan, D. W., Park, R. B., Cho, Y. R. and De Cooman, B. C. (2010). Influence of isothermal deformation conditions on the mechanical properties of 22MnB5 HPF steel. Steel Research Int. 81, 4, 292–298.
Han, X., Zhong, Y., Xin, P., Cui, Z. and Chen, J. (2017). Research on one-step quenching and partitioning treatment and its application in hot stamping process. Proc. Institution of Mechanical Engineers, Part B: J. Engineering Manufacture 231, 11, 1972–1982.
Jha, G., Das, S., Sinha, S., Lodh, A. and Haldar, A. (2013). Design and development of precipitate strengthened advanced high strength steel for automotive application. Materials Science and Engineering: A, 561, 394–402.
Koistinen, D. P. (1959). A general equation prescribing the extent of the austenite-martensite transformation in pure iron-carbon alloys and carbon steels. Acta Metallurgica 7, 1, 59–60.
Kim, D. Y., Kim, H. Y., Lee, S. H. and Kim, H. K. (2015). Life estimation of hot press forming die by using interface heat transfer coefficient obtained from inverse analysis. Int. J. Automotive Technology 16, 2, 285–292.
Kuziak, R., Kawalla, R. and Waengler, S. (2008). Advanced high strength steels for automotive industry. Archives of Civil and Mechanical Engineering 8, 2, 103–117.
Karbasian, H. and Tekkaya, A. E. (2010). A review on hot stamping. J. Materials Processing Technology 210, 15, 2103–2118.
Liu, H. S., Xing, Z. W., Bao, J. and Song, B. Y. (2010). Investigation of the hot-stamping process for advanced high-strength steel sheet by numerical simulation. J. Materials Engineering and Performance 19, 3, 325–334.
Lim, W. S., Choi, H. S., Ahn, S. Y. and Kim, B. M. (2014). Cooling channel design of hot stamping tools for uniform high-strength components in hot stamping process. Int. J. Advanced Manufacturing Technology 70, 5–8, 1189–1203.
Li, N., Lin, J., Balint, D. S. and Dean, T. A. (2016). Experimental characterization of the effects of thermal conditions on austenite formation for hot press forming of boron steel. J. Materials Processing Technology, 231, 254–264.
Mori, K., Bariani, P. F., Behrens, B. A., Brosius, A., Bruschi, S., Maeno, T., Merklein, M. and Yanagimoto, J. (2017). Hot stamping of ultra-high strength steel parts. CIRP Annals 66, 2, 755–777.
Merklein, M. and Lechler, J. (2006). Investigation of the thermo-mechanical properties of hot stamping steels. J. Materials Processing Technology 177, 1–3, 452–455.
Merklein, M., Wieland, M., Lechner, M., Bruschi, S. and Ghiotti, A. (2016). Hot stamping of boron steel sheets with tailored properties: A review. J. Materials Processing Technology, 228, 11–24.
Min, J., Lin, J. and Min, Y. A. (2013). Effect of thermo-mechanical process on the microstructure and secondary-deformation behavior of 22MnB5 steels. J. Materials Processing Technology 213, 6, 818–825.
Nikravesh, M., Naderi, M. and Akbari, G. H. (2012). Influence of hot plastic deformation and cooling rate on martensite and bainite start temperatures in 22MnB5 steel. Materials Science and Engineering: A, 540, 24–29.
Omer, K., Kortenaar, L. T., Butcher, C., Worswick, M., Malcolm, S. and Detwiler, D. (2017). Testing of a hot stamped axial crush member with tailored properties — Experiments and models. Int. J. Impact Engineering, 103, 12–28.
Schicchi, D. S. and Hunkel, M. (2016). Transformation plasticity and kinetic during bainite transformation on a 22MnB5 steel grade. Materwiss Werksttech 47, 8, 771–779.
Shapiro, A. B. (2009). Using LS-Dyna for hot stamping. Proc. 7th European LS-DYNA Users Conf., Salzburg, Austria, 1–9.
Taylor, T. and Clough, A. (2018). Critical review of automotive hot-stamped sheet steel from an industrial perspective. Materials Science and Technology 34, 7, 809–861.
Tekkaya, A. E., Karbasian, H., Homberg, W. and Kleiner, M. (2007). Thermo-mechanical coupled simulation of hot stamping components for process design. Production Engineering 1, 1, 85–89.
Valls, I., Casas, B., Rodríguez, N. and Paar, U. (2010). Benefits from using high thermal conductivity tool steels in the hot forming of steels. La Metallurgia Italiana, 11–12, 23–28.
Wang, W., Zhang, L., Guo, M., Huang, L. and Wei, X. (2016). Non-isothermal deformation behavior and FE simulation of ultrahigh strength BR1500HS steel in hot press forming process. Int. J. Advanced Manufacturing Technology 87, 9–12, 2951–2965.
Won, C., Lee, S., Seo, J., Park, S. H. and Yoon, J. (2018). Stripping failure of punching pin in GPa-grade steels. Int. J. Advanced Manufacturing Technology 94, 1–4, 73–83.
Zhao, K., Chang, Y., Hu, P. and Wu, Y. (2016). Influence of rapid cooling pretreatment on microstructure and mechanical property of hot stamped AHSS part. J. Materials Processing Technology, 228, 68–75.
Acknowledgement
This work was supported by the National Research Foundation of Korea (NRF) grant funded by the Korean government (2016R1C1B1006875). This work was also supported by the “Human Resources Program in Energy Technology” of the Korean Institute of Energy Technology Evaluation and Planning (KETEP), granted by the Ministry of Trade, Industry & Energy, Republic of Korea (no. 20174010201310).
The authors declare that they have no conflicts of interest.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kim, Hg., Won, C., Choi, S. et al. Thermo-Mechanical Coupled Analysis of Hot Press Forming with 22MnB5 Steel. Int.J Automot. Technol. 20, 813–825 (2019). https://doi.org/10.1007/s12239-019-0076-x
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12239-019-0076-x