Skip to main content
SpringerLink
Log in

Pool boiling of R-123/MO and R-134a/POE lubricant mixtures on pored surfaces

  • Original Article
  • Published:
Journal of Mechanical Science and Technology Aims and scope Submit manuscript

Abstract

In a flooded refrigerant evaporator, where enhanced tubes are frequently used, lubrication oil inevitably circulates with the refrigerant. However, the literature shows that systematic studies on this subject are lacking. In this study, the effects of oil on the pool boiling of pored surfaces having a range of pore diameter (0.1 to 0.3 mm) and pitch (0.75 to 3.0 mm) were investigated using R-134a/polyester oil (POE) and R-123/mineral oil (MO) mixtures. The saturation temperature was 26.7 °C, and the oil concentration was varied up to 10 %. The results showed that the oil reduced the heat transfer coefficient. This was true for all the pored surface as well as the smooth surface. Overall, the samples having a ‘small open area’ yielded a significant degradation at a low heat flux, whereas the samples having a ‘large open area’ yielded a noticeable degradation at a high heat flux. Meanwhile, the heat transfer degradation was larger for R-134a/POE than R-123/MO, and the reason was attributed to the oil effect on the surface tension, which was stronger for R-134a/POE. The flow visualization results showed that, with the increase of oil concentration, the bubble departure diameter decreased. Similarly, the bubble generation frequency and nucleation site density decreased. These changes of the bubble dynamic parameters certainly were responsible for the heat transfer degradation. A model was developed extending that of Pastuszko et al. [27] to predict the heat transfer coefficients as well as bubble dynamic parameters. The model predicted 92 % of the heat transfer coefficients within ± 40 %.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. K. I. Bell, G. F. Hewitt and S. D. Morris, Nucleate pool boiling of refrigerant/oil mixtures, Exp. Heat Trans., 1 (1987) 71–86.

    Article  Google Scholar 

  2. S. Chongrungreong and H. J. Sauer Jr., Nucleate boiling performance of refrigerants and refrigerant-oil mixtures, J. Heat Transfer, 102 (1980) 701–705.

    Article  Google Scholar 

  3. R. L. Webb and W. F. McQuade, Pool boiling of R-11 and R-123 oil-refrigerant mixtures on plain and enhanced tube boiling, ASHRAE Trans., 99 (1) 1225–1236.

  4. K. Stephan and J. Mitrovic, Heat transfer in natural convective boiling of refrigerant oil mixtures, 7th Int. Heat Transfer Conf., 4 (1982) 73–87.

  5. S. B. Memory, D. C. Sugiyama and P. J. Marto, Nucleate pool boiling of polyolester oil R-114 and R-114/oil mixtures from smooth and enhanced surfaces-I. single tubes, Int. J. Heat Mass Transfer, 38 (1995) 1347–1361.

    Article  Google Scholar 

  6. A. Kumar, X.-Z. Wang, B. J. Lakshmi, J.-T. Hung, Y.-K Chen and C.-C. Wang, Nucleate pool boiling of R-134a and R-14a/POE lubricant mixtures on smooth tube, Applied Thermal Eng., 185 (2021) 166359.

    Article  Google Scholar 

  7. M. A. Kedzierski, The effect of lubricant concentration, miscibility and viscosity on R-134a pool boiling, Int. J. Refrig., 24 (2001) 348–366.

    Article  Google Scholar 

  8. V. Zarnescu, R. L. Webb and L.-H. Chien, Effect of oil on the boiling performance of structured and porous surfaces, HVAC&R Research, 6 (1) (2000) 41–53.

    Article  Google Scholar 

  9. N.-H. Kim and D.-Y. Kim, Pool boiling of R-123/oil mixtures on enhanced tubes having different pore sizes, Int. J. Heat Mass Transfer, 53 (2010) 2311–2317.

    Article  Google Scholar 

  10. A. S. Wanniarachchi, P. J. Marto and J. T. Reilly, The effect of oil contamination on the nucleate pool boiling performance of R-114 from a porous coated surface, ASHRAE Trans., 92 (2) (1986) 339–348.

    Google Scholar 

  11. S. B. Memory, G. Bertsch and P. J. Marto, Pool boiling of HCFC-124/oil mixtures from smooth and enhanced tubes, Heat Transfer with Alternate Refrigerants, HTD-vol. 243 (1993) 9–18.

    Google Scholar 

  12. N.-H. Kim, E.-J. Lee and H.-W. Byun, Pool boiling of R-134a/oil mixtures on enhanced tubes having different pore and gap sizes, Int. J. Heat Mass Trans., 66 (2013) 118–127.

    Article  Google Scholar 

  13. A. Mondal and N.-H. Kim, Nucleate pool boiling of R-134a on enhanced horizontal surfaces having pores on sub-tunnels, J. Enhanced Heat Trans., 26 (3) (2019) 195–216.

    Article  Google Scholar 

  14. D. Y. Goswani, D. O. Shah, C. K. Jotshi, S. Bhagwat, M. Leung and A. Gregory, Foaming characteristics of refrigerant/lubricant mixtures, ASHRAE Winter Meetings, Philadelphia (1997) CONF-970101-4.

  15. S-oil Corporation, http://www.s-oil.com/en/energy/Lube BaseOil.aspx.

  16. S. Mehdi, Y. Shah, A. Mondal and N.-H. Kim, Bubble dynamics of R-134a boiling in enhanced surfaces having pores on sub-tunnels, Int. J. Heat Mass Trans., 155 (2020) 119753.

    Article  Google Scholar 

  17. S. J. Kline and F. A. McClintock, The description of uncertainties in single sample experiments, Mechanical Engineering, 75 (1953) 3–9.

    Google Scholar 

  18. M. G. Cooper, Heat flow rates in saturated nucleate pool boiling - A wide range examination with reduced properties, Advances in Heat Transfer, 16 (1984) 157–238.

    Article  Google Scholar 

  19. H. C. Lee, S. Kim, B. D. Oh and M. H. Kim, Single bubble growth in saturated pool boiling of binary mixtures, Int. J. Multiphase Flow, 20 (2004) 697–710.

    Article  Google Scholar 

  20. L.-H. Chien and R. L. Webb, A nucleate boiling model for structured enhanced surfaces, Int. J. Heat Mass Transfer, 41 (1998) 2183–2195.

    Article  Google Scholar 

  21. K. Mohrlok, K. Spindler and E. Hahne, The influence of a low viscosity oil on the pool boiling heat transfer of the refrigerant R507, Int. J. Refrig., 24 (2001) 25–40.

    Article  Google Scholar 

  22. M. K. Jensen and D. L. Jackman, Prediction of nucleate pool boiling heat transfer coefficients of refrigerant-oil mixtures, J. Heat Transfer, 106 (1984) 133–140.

    Google Scholar 

  23. J. G. Collier and J. R. Thome, Convective Boiling and Condensation, Oxfordshire: Oxford University Press (1996).

    Google Scholar 

  24. J.-T. Hung, Y.-K. Shih, S.-R. Sheng and C.-C. Wang, The effect of refrigeration lubricant properties on nucleate pool boiling heat transfer performance, Int. Refrig. Air Cond. Conf., Paper 1921 (2018).

  25. W. Nakayama, T. Daikoku, H. Kuwahara and T. Nakajima, Dynamic model of enhanced boiling heat transfer on porous surfaces, part II: analytical modeling, J. Heat Transfer, 102 (1980) 451–456.

    Article  Google Scholar 

  26. L.-H. Chien and R. L. Webb, A nucleate boiling model for structured enhanced surfaces, Int. J. Heat Mass Transfer, 41 (1998) 2183–2195.

    Article  Google Scholar 

  27. R. Pastuszko and T. M. Wojcik, Experimental investigations and a simplified model for pool boiling on microfins with sintered perforated foil, Exp. Thermal Fluid Sci., 63 (2015) 34–44.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Incheon National University, Incheon, Korea

    Yousaf Shah & Nae-Hyun Kim

Authors
  1. Yousaf Shah
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Nae-Hyun Kim
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Nae-Hyun Kim.

Additional information

Nae-Hyun Kim is a Professor in School of Mechanical System Engineering, University of Incheon. He received Ph.D. from Penn State University in 1989. His interest includes heat transfer enhancement, boiling and condensation in minichannels, flow distribution in flow heat exchangers, etc.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Shah, Y., Kim, NH. Pool boiling of R-123/MO and R-134a/POE lubricant mixtures on pored surfaces. J Mech Sci Technol 36, 467–478 (2022). https://doi.org/10.1007/s12206-021-1244-2

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s12206-021-1244-2

Keywords

Search

Navigation