Skip to main content
SpringerLink
Log in

Effects of aerodynamic turbulator on efficiency improvement and heat transfer enhancement of the internal flow in a pipe

  • Published:
Sādhanā Aims and scope Submit manuscript

Abstract

The application of turbulators to improve thermal performance and thermal enhancement in heat exchangers because of the significance of energy management and optimization is one of the interesting topics for researchers. Analysis of aerodynamic turbulator in internal flow has been less discussed in previous studies. Therefore, the present work focuses on the effect of a perforated sphere turbulator in a circular pipe with square, circular, oval, and hexagonal geometry holes on turbulent flow characteristics and thermal performance. These turbulators are placed with equal obstruction against the flow of air passing inside the pipe at Re = 6000–24000 in wall conditions of constant heat flux. Ansys Fluent software is used for numerical solutions, and the results are validated with an experimental paper. According to the results, the hexagonal geometry creates less pressure drop than other geometries. The thermal performance in the pipe with innovative aerodynamic turbulators is improved compared to the smooth pipe and the pipe equipped with conventional turbulators. The highest thermal performance of 1.256 is obtained for the turbulator with an oval hole. Also, the range of Nusselt number compared to the plain pipe for turbulator with circular, hexagonal, square, and oval holes increases by 1.97–2.46, 2.24–2.65, 1.58–1.89, and 2.48–2.81 times, respectively. The effect of the proposed new turbulators was compared with previous studies in this field, and the results are promising.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21

Similar content being viewed by others

Abbreviations

V :

Flow velocity (m/s)

D p :

Pipe diameter (m)

d s :

Sphere diameter

d c :

The diameter of the circular hole

L 0 :

Length of the pipe

K :

The side of the hexagonal hole

a :

Square hole side

b :

The small radius of the oval hole

c :

The large radius of the oval hole

A :

Surface area (m2)

ν :

Represents the kinematic viscosity

F :

Turbulence kinetic energy

Re :

Reynolds number (=\(\rho V\) D/\(\mu \))

Nu :

Nusselt number

f :

Friction factor

S :

The distance between two turbulators

Q :

Volume flow (m3 /s)

Nu s :

The average Nu for the smooth pipe

f s :

The average f for the smooth pipe

ε :

Turbulent dissipation (J/kg.s)

E :

Energy

h :

Heat transfer coefficient \((\frac{{\text{W}}}{{{\text{m}}^{{2 }} {\text{k}}}})\)

ω:

Turbulence frequency

F1 and F2:

Blending functions

S:

Smooth

P:

Pipe

b:

Bulk

\(\rho \) :

Density (kg/m3)

\(\mu \) :

Absolute viscosity (kg/m s))

\(\eta \) :

Thermal performance factor

References

  1. Bergles A E 1973 Techniques to augment heat transfer. Handbook of heat transfer. New York. McGraw-Hill Book Co. 10–11

  2. Arasteh H, Rahbari A, Mashayekhi R, Keshmiri A, Mahani R B and Talebizadehsardari P 2021 Effect of pitch distance of rotational twisted tape on the heat transfer and fluid flow characteristics. Int. J. Therm. Sci. 170: 106–966

    Article  Google Scholar 

  3. Ibrahim M M, Essa M A and Mostafa N H 2019 A computational study of heat transfer analysis for a circular tube with conical ring turbulators. Int. J. Thermal Sci. 137: 138–160

    Article  Google Scholar 

  4. Sharma S L, Singh S, Debbarma A and Mehra K S 2023 Experimental assessment of thermal performance and fluid flow characteristics of perforated hollow elliptical insert in a tube heat exchanger. Arab. J. Sci. Eng. 48(9): 11499–11510

    Article  Google Scholar 

  5. Patil A S, Kore S S and Sane N K 2020 Thermal performance of tube exchanger enhanced with hexagonal ring turbulators. Exp. Heat Transf. 33: 455–470

    Article  Google Scholar 

  6. Abdelmaksoud W A, Mahfouz A E and Khalil E E 2021 Thermal performance enhancement for heat exchanger tube fitted with vortex generator inserts. Heat Transf. Eng. 42: 1861–1875

    Article  Google Scholar 

  7. Rajan A, Sneha S, Prasad L and Prasad B N 2023 Performance intensification of heat exchanger tube fitted with double hyperbolic-cut twisted tape in turbulent flow. J. Braz. Soc. Mech. Sci. Eng. 45(9): 477

    Article  Google Scholar 

  8. Liu X, Shah Z, Ikramullah and Alzahrani M R Numerical modeling of nanofluid exergy loss within tube with multi-helical tapes. Eur. Phys. J. Plus 137(1): 152

  9. Padmanabhan S, Selvamuthukumar M, Ganesan S, Baskar S and Sharma A Investigation of heat transfer characteristics in double tube heat exchanger with helical turbulator using CFD. In Advancement in Materials : 531–541

  10. Manh T D, Marashi M, Mofrad A M, Taleghani A H and Babazadeh H 2021 The influence of turbulator on heat transfer and exergy drop of nanofluid in heat exchangers. J. Thermal Anal. Calorim. 145: 201–209

    Article  Google Scholar 

  11. Suri A R S, Kumar A and Maithani R 2018 Experimental investigation of heat transfer and fluid flow behaviour in multiple square perforated twisted tape with square wing inserts heat exchanger tube. Heat Mass Transf. 54: 1813–1826

    Article  Google Scholar 

  12. Alizadeh A et al. 2023 Numerical investigation of the effect of the turbulator geometry (disturber) on heat transfer in a channel with a square section. Alex. Eng. J. 69: 38–402

    Article  Google Scholar 

  13. Bartwal A, Gautam A, Kumar M, Mangrulkar C K and Chamoli S 2018 Thermal performance intensification of a circular heat exchanger tube integrated with compound circular ring–metal wire net inserts. Chem. Eng. Process. Process Intensification 124: 50–70

    Article  Google Scholar 

  14. Kumar V and Sahoo R R 2022 Analysis of heat exchanger equipped with various twisted turbulator inserts utilizing tripartite hybrid nanofluids. J. Thermal Anal. Calorim. 147(19): 10845–10863

    Article  Google Scholar 

  15. Azizi Z, Rostampour V, Jafarmadar S, Khorasani S and Abdzadeh B Performance evaluation of horizontal straight tube equipped with twisted tape turbulator with air–water two-phase flow as working fluid. J. Thermal Anal. Calorim. 147(6): 4339–4353

  16. Khanmohammadi S, Jahangiri A, Nazari F and Azimi N 2023 Numerical study of a dimpled tube with conical turbulator using the first and second laws of thermodynamics. J. Thermal Anal. Calorim. 148(16): 8497–8510

    Article  Google Scholar 

  17. Mousavi S M S and Alavi S M A 2022 Experimental and numerical study to optimize flow and heat transfer of airfoil-shaped turbulators in a double-pipe heat exchanger. Appl. Thermal Eng. 215: 118–961

    Article  Google Scholar 

  18. Firat I, Karagoz S, Yildirim O and Yilmaz M 2023 Performance and entropy production analysis of angle blade turbulators used to increase heat transfer. J. Thermal Anal. Calorim. 148(15): 7811–7828

    Article  Google Scholar 

  19. Nalavade S P, Prabhune C L and Sane N K 2019 Effect of novel flow divider type turbulators on fluid flow and heat transfer. Thermal Sci. Eng. Prog. 9: 322–331

    Article  Google Scholar 

  20. Banihashemi S, Assari M R, Javadi S and Vahidifar S 2021 Experimental study of the effect of disk obstacle rotating with Different angular ratios on heat transfer and pressure drop in a pipe with turbulent flow. J. Thermal Anal. Calorim. 144: 1401–1416

    Article  Google Scholar 

  21. Banihashemi S, Assari M, Javadi S and Vahidifar S 2022 Turbulent flow thermal characteristics in a pipe with ring insert, An experimental and numerical study. Chem. Eng. Process. Process Intensif. 172: 108–780

    Article  Google Scholar 

  22. Banihashemi S H, Assari M R, Javadi S M and Vahidifar S 2022 Experimental and numerical study of thermal-hydraulic performance in a heat exchanger tube with circular ring’s angular cutting inserts. Exp. Heat Transf. 1–19

  23. Pan C, Alqahtani A M, Wei H, Sulaiman N, Elsiddieg A M and Ghoushchi S 2024 Heat transfer enhancement of a heat exchanger using novel multiple perforated magnetic turbulators (MPMT). An experimental study. Int. J. Thermal Sci. 195: 108–642

    Article  Google Scholar 

  24. Ravanbakhsh M, Deymi-Dashtebayaz M and Rezapour M 2022 Numerical investigation on the performance of the double tube heat exchangers with different tube geometries and Turbulators. J. Thermal Anal. Calorim. 147(20): 11313–11330

    Article  Google Scholar 

  25. Barzegar A and Jalali Vahid D 2019 Numerical study on heat transfer enhancement and flow characteristics of double pipe heat exchanger fitted with rectangular cut twisted tape. Heat Mass Transf. 55(12): 3455–3472

    Article  Google Scholar 

  26. Nakhchi M, Esfahani J and Kim K 2020 Numerical study of turbulent flow inside heat exchangers using perforated louvered strip inserts. Int. J. Heat Mass Transf. 148: 119–143

    Article  Google Scholar 

  27. Tusar M H, Bhowmik P K, Salam B, Ahamed J U and Kim J K 2021 Convective heat transfer and friction factor characteristics of helical strip inserted annuli at turbulent flow. Int. J. Heat Mass Transf. 176: 121–422

    Article  Google Scholar 

  28. Zhang S, Lu Dong C and Cha S H 2019 Thermal characteristics of perforated self-rotating twisted tapes in a double-pipe heat exchanger. Appl. Thermal Eng. 162: 114–296

    Article  Google Scholar 

  29. Zheng N, Liu P, Wang X, Shan F, Liu Z and Liu W 2017 Numerical simulation and optimization of heat transfer enhancement in a heat exchanger tube fitted with vortex rod inserts. Appl. Thermal Eng. 123: 471–484

    Article  Google Scholar 

  30. Saadat M, Aghlichanche A, Ataelahi A, Mohammadi O and Shafii M B 2022 Thermal study of the internal flow in a circular tube with vibrational ball turbulators. Int. J. Heat Mass Transf. 196: 123–276

    Article  Google Scholar 

  31. Farsi M, Khoshvaght-Aliabadi M and Alimoradi A 2021 A parametric study on heat transfer and pressure drop characteristics of circular tube with alternating flattened flow path. Int. J. Thermal Sci. 160: 106671

    Article  Google Scholar 

  32. Pourramezan M, Ajam H, Raoufi M A and Abadeh A 2020 Performance evaluation and optimization of design parameters for twisted conical strip inserts in tubular laminar flow using Taguchi approach. Int. J. Thermal Sci. 152: 106–324

    Article  Google Scholar 

  33. Yuan W, Fang G, Zhang X, Tang Y, Wan Z and Zhang S 2018 Heat transfer and friction characteristics of turbulent flow through a circular tube with ball turbulators. Appl. Sci. 8: 776

    Article  Google Scholar 

  34. Al-Obaidi A R and Chaer I 2021 Flow field structure characteristics of thermo-hydraulic and heat transfer performance analysis in a three dimensions circular tube with different ball turbulators configurations. Arab. J. Sci. Eng. 46: 12253–12282

    Article  Google Scholar 

  35. Banihashemi S, Assari M, Javadi S and Vahidifar S 2022 The effect of flow excitation with stationary and rotating obstacles in a heat exchanger tube on thermal-hydraulic characteristics. Iran. J. Sci. Technol. Trans. Mech. Eng. 46: 465–480

    Article  Google Scholar 

  36. Banihashemi S, Assari M R, Javadi S M and Vahidifar S 2022 Thermal performance investigation in circular tube with stationary and rotating conical-obstacle inserts. J. Thermophys. Heat Transf. 36: 242–255

    Article  Google Scholar 

  37. Hanhold A J, Curbelo A and Kapat J S Investigation of Heat Transfer Enhancement within a Concentric Annulus using Helicoil Turbulators. 15th International Energy Conversion Engineering Conference.

  38. Buchanan T, Garcia D, Hossain J and Kapat J S Correction: Investigation into the Feasibility of Using Turbulators in Liquid Rocket Combustion Chamber Cooling Channels Using a Conjugate Heat Transfer Analysis. 2018 Joint Propulsion Conference

  39. Afshari F, Ghasemi Zavaragh H and Di Nicola G 2019 Numerical analysis of ball-type turbulators in tube heat exchangers with computational fluid dynamic simulations. Int. J. Environ. Sci. Technol. 16: 3771–3780

    Article  Google Scholar 

  40. Mohammad javadi S and Banihashemi S 2023 Study of thermal performance and optimization of city gas station heaters equipped with turbulator in the fire tube section. Thermal Sci. Eng. Prog. 37:101–573

  41. Menter F R 2009 Review of the shear-stress transport turbulence model experience from an industrial perspective. Int. J. Comput. Fluid Dyn. 23: 305–316

    Article  Google Scholar 

  42. Fluent A Ansys fluent. 2015 Academic Research. Release. 14

  43. Ansys A ANSYS® Fluent. Academic Research. 2015

  44. Jasiński P B 2014 Numerical study of the thermo-hydraulic characteristics in a circular tube with ball turbulators. Part 1: PIV experiments and a pressure drop’. Int. J. Heat Mass Transf. 74: 48–59

    Article  Google Scholar 

  45. Webb R L 1981 Performance evaluation criteria for use of enhanced heat transfer surfaces in heat exchanger design. Int. J. Heat Mass Transf. 24: 715–726

    Article  Google Scholar 

  46. Dittus F and Boelter L 1930 Publications on engineering. University of California. Berkeley 2: 443–461

  47. Gnielinski V 1976 New equations for heat and mass transfer in turbulent pipe and channel flow. Int. Chem. Eng. 16: 359–368

    Google Scholar 

  48. Petukhov B S 1970 Heat transfer and friction in turbulent pipe flow with variable physical properties. Adv. Heat Transf. 503–564

  49. Moody L F 1944 Friction factors for pipe flow. Trans. ASME 66: 671–684

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Mechanical Engineering, Faculty of Engineering, Alzahra University, Tehran, 09121328094, Iran

    Mohammadreza Assari

  2. Optimizing Energy and Carbon Consumption, National Iranian Gas Company, Semnan, Iran

    Seyedhadi Banihashemi

  3. Department of Mechanical Engineering, Jundi- Shapur University of Technology, Dezful, Iran

    Seyedhadi Banihashemi, Milad Setareh & Amir Mohammad Nargesi Motlagh

Authors
  1. Mohammadreza Assari
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Seyedhadi Banihashemi
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Milad Setareh
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Amir Mohammad Nargesi Motlagh
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to Mohammadreza Assari or Seyedhadi Banihashemi.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Assari, M., Banihashemi, S., Setareh, M. et al. Effects of aerodynamic turbulator on efficiency improvement and heat transfer enhancement of the internal flow in a pipe. Sādhanā 49, 196 (2024). https://doi.org/10.1007/s12046-024-02519-7

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s12046-024-02519-7

Keywords

Search

Navigation