Abstract
The inadvertent release of crude oil and its derivatives into aquatic ecosystems has emerged as a significant and concerning environmental issue, often leading to catastrophic accidents. Ongoing research efforts are diligently working toward devising effective remedies to curtail and alleviate the adverse impacts of these incidents on the delicate balance of aquatic life. Amidst these endeavors, cellulose, an eco-friendly and cost-effective material, has garnered attention for its potential in addressing this formidable challenge. In this pioneering study, we delve into a novel approach by harnessing waste-derived cellulose to combat oil spills within aquatic environments. Specifically, cellulose was extracted from post-consumer waste cloths (PCWCs) and subjected to a transformative treatment involving strategically chosen silanating agents. This treatment facilitated the creation of a three-dimensional, water-repelling matrix, characterized by a remarkable hydrophobic nature, exemplified by a substantial contact angle of 126.2°. The resultant matrix exhibited exceptional reusability, demonstrating consistent performance over five successive cycles, and showcased an impressive oil absorption capacity of up to 24.36 g/g. Notably, the engineered polyester sponge exhibited a remarkable buoyancy, being approximately 28.5 times lighter than water, and boasted a density ranging from 0.026 to 0.040 g/cm3. This innovative approach not only presents a tangible solution for oil–water separation during scenarios of marine or environmental oil spills, but it also offers a sustainable and valuable application for well-processed PCWCs. By effectively harnessing the intrinsic properties of cellulose and employing meticulous design, this study represents a significant stride toward mitigating the ecological impact of accidental oil discharges in aquatic ecosystems.
Graphical Abstract
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Adebajo MO, Frost RL, Kloprogge JT et al (2003) Porous materials for oil spill cleanup: a review of synthesis and absorbing properties. J Porous Mater 10:159–170. https://doi.org/10.1023/A:1027484117065
Adsul M, Soni SK, Bhargava SK, Bansal V (2012) Facile Approach for the dispersion of regenerated cellulose in aqueous system in the form of nanoparticles. Biomacromol 13:2890–2895. https://doi.org/10.1021/bm3009022
Akhlamadi G, Goharshadi EK (2021) Sustainable and superhydrophobic cellulose nanocrystal-based aerogel derived from waste tissue paper as a sorbent for efficient oil/water separation. Process Saf Environ Prot 154:155–167. https://doi.org/10.1016/j.psep.2021.08.009
Alaa El-Din G, Amer AA, Malsh G, Hussein M (2018) Study on the use of banana peels for oil spill removal. Alex Eng J 57:2061–2068. https://doi.org/10.1016/j.aej.2017.05.020
Arkles B (2006) Hydrophobicity, Hydrophilicity and Silanes. Paint and Coatings Industry 22:114
Aurell J, Gullett BK (2010) Aerostat sampling of PCDD/PCDF emissions from the gulf oil spill in situ burns. Environ Sci Technol 44:9431–9437. https://doi.org/10.1021/es103554y
Baghel V, Sharma DK, Sikarwar BS, et al (2019) Tailoring the hydrophobicity of copper surface with ion beam irradiation. Radiat Eff Defects Solids 174:. https://doi.org/10.1080/10420150.2018.1564149
Baig N, Kammakakam I (2021) Removal of oily contaminants from water by using the hydrophobic Ag nanoparticles incorporated dopamine modified cellulose foam. Polymers (Basel) 13:. https://doi.org/10.3390/polym13183163
Beall A (2000) Fast fashions leading to a mountain of clothing being thrown away each year and as a huge impact on the environment, so can we turn our unwanted garments into something useful?. In: Accessed 13 July 2020
Ben Hammouda S, Chen Z, An C, Lee K (2021) Recent advances in developing cellulosic sorbent materials for oil spill cleanup: a state-of-the-art review. J Clean Prod 311:127630. https://doi.org/10.1016/j.jclepro.2021.127630
Broje V, Keller AA (2006) Improved mechanical oil spill recovery using an optimized geometry for the skimmer surface. Environ Sci Technol 40:7914–7918. https://doi.org/10.1021/es061842m
Broje V, Keller AA (2007) Effect of operational parameters on the recovery rate of an oleophilic drum skimmer. J Hazard Mater 148:136–143. https://doi.org/10.1016/j.jhazmat.2007.02.017
Bruel C, Tavares JR, Carreau PJ, Heuzey M-C (2019) The structural amphiphilicity of cellulose nanocrystals characterized from their cohesion parameters. Carbohydr Polym 205:184–191. https://doi.org/10.1016/j.carbpol.2018.10.026
Carpenter A (2019) Oil pollution in the North Sea: the impact of governance measures on oil pollution over several decades. Hydrobiologia 845:109–127. https://doi.org/10.1007/s10750-018-3559-2
Cervin NT, Aulin C, Larsson PT, Wågberg L (2012) Ultra porous nanocellulose aerogels as separation medium for mixtures of oil/water liquids. Cellulose 19:401–410. https://doi.org/10.1007/s10570-011-9629-5
Chau MQ, Truong TT, Hoang AT, Le TH (2021) Oil spill cleanup by raw cellulose-based absorbents: a green and sustainable approach. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects 1–14. https://doi.org/10.1080/15567036.2021.1928798
Chen X, Weibel JA, Garimella SV (2016) Continuous oil-water separation using polydimethylsiloxane-functionalized melamine sponge. Ind Eng Chem Res 55:3596–3602. https://doi.org/10.1021/acs.iecr.6b00234
Cheng Z, Wang J, Lai H et al (2015) pH-controllable on-demand oil/water separation on the switchable superhydrophobic/superhydrophilic and underwater low-adhesive superoleophobic copper mesh film. Langmuir 31:1393–1399. https://doi.org/10.1021/la503676a
Choi HM, Cloud RM (1992) Natural sorbents in oil spill cleanup. Environ Sci Technol 26:772–776. https://doi.org/10.1021/es00028a016
Dhumal PS, Khose RV, Wadekar PH et al (2021) Graphene-bentonite supported free-standing, flexible membrane with switchable wettability for selective oil–water separation. Sep Purif Technol 266:118569. https://doi.org/10.1016/j.seppur.2021.118569
Dong B, Guo Y, Sun S et al (2020) Shish–kebab-structured UHMWPE coating for efficient and cost-effective oil-water separation. ACS Appl Mater Interfaces 12:58252–58262. https://doi.org/10.1021/acsami.0c17900
Doshi B, Sillanpää M, Kalliola S (2018) A review of bio-based materials for oil spill treatment. Water Res 135:262–277. https://doi.org/10.1016/j.watres.2018.02.034
Esfahani MR, Taylor A, Serwinowski N et al (2020) Sustainable novel bamboo-based membranes for water treatment fabricated by regeneration of bamboo waste fibers. ACS Sustain Chem Eng 8:4225–4235. https://doi.org/10.1021/acssuschemeng.9b07438
Fan S, Wang Z, Li Z et al (2022) A versatile and efficient method to fabricate superhydrophobic biomass for removing/ collecting oil contaminants. J Market Res 19:1600–1613. https://doi.org/10.1016/j.jmrt.2022.05.150
Feng C, Yi Z, She F et al (2016) Superhydrophobic and superoleophilic micro-wrinkled reduced graphene oxide as a highly portable and recyclable oil sorbent. ACS Appl Mater Interfaces 8:9977–9985. https://doi.org/10.1021/acsami.6b01648
Giang HN, Nguyen TX, Huynh TV et al (2020) Fabrication of superhydrophobic surface using one-step chemical treatment. Surfaces and Interfaces 21:100673. https://doi.org/10.1016/j.surfin.2020.100673
Gong X, He S (2020) Highly durable superhydrophobic polydimethylsiloxane/silica nanocomposite surfaces with good self-cleaning ability. ACS Omega 5:4100–4108. https://doi.org/10.1021/acsomega.9b03775
Gu J, Xiao P, Huang Y et al (2015) Controlled functionalization of carbon nanotubes as superhydrophobic material for adjustable oil/water separation. J Mater Chem A 3:4124–4128. https://doi.org/10.1039/C4TA07173E
Gupta R, Kumar P, Yadav V et al (2015) Challenges and opportunities in fabrication of transparent superhydrophobic surfaces. Curr Nanosci 12:1. https://doi.org/10.2174/1573413712666151216221401
Han S, Sun Q, Zheng H et al (2016) Green and facile fabrication of carbon aerogels from cellulose-based waste newspaper for solving organic pollution. Carbohydr Polym 136:95–100. https://doi.org/10.1016/j.carbpol.2015.09.024
Hassan H, Ismail A, Ahmad S, Soon CF (2017) Super-hydrophobic green corrosion inhibitor on carbon steel. IOP Conf Ser Mater Sci Eng 215:012023. https://doi.org/10.1088/1757-899X/215/1/012023
Heinonen S, Huttunen-Saarivirta E, Nikkanen J-P et al (2014) Antibacterial properties and chemical stability of superhydrophobic silver-containing surface produced by sol–gel route. Colloids Surf A Physicochem Eng Asp 453:149–161. https://doi.org/10.1016/j.colsurfa.2014.04.037
Hoang AT, Pham XD (2021) An investigation of remediation and recovery of oil spill and toxic heavy metal from maritime pollution by a new absorbent material. J Marine Eng Technol 20:159–169. https://doi.org/10.1080/20464177.2018.1544401
Hooda A, Goyat MS, Gupta R et al (2017) Synthesis of nano-textured polystyrene/ZnO coatings with excellent transparency and superhydrophobicity. Mater Chem Phys 193:447–452. https://doi.org/10.1016/j.matchemphys.2017.03.011
Hooda A, Goyat MS, Pandey JK et al (2020) A review on fundamentals, constraints and fabrication techniques of superhydrophobic coatings. Prog Org Coat 142:105557. https://doi.org/10.1016/j.porgcoat.2020.105557
Hüsing N, Schubert U (1998) Aerogels—airy materials: chemistry, structure, and properties. Angew Chem Int Ed 37:22–45. https://doi.org/10.1002/(SICI)1521-3773(19980202)37:1/2%3c22::AID-ANIE22%3e3.0.CO;2-I
Ifelebuegu AO, Johnson A (2017) Nonconventional low-cost cellulose- and keratin-based biopolymeric sorbents for oil/water separation and spill cleanup: A review. Crit Rev Environ Sci Technol 47:964–1001. https://doi.org/10.1080/10643389.2017.1318620
Ioelovich M (2021) Adjustment of Hydrophobic Properties of Cellulose Materials. Polymers (Basel) 13:. https://doi.org/10.3390/polym13081241
Jamaly S, Giwa A, Hasan SW (2015) Recent improvements in oily wastewater treatment: Progress, challenges, and future opportunities. J Environ Sci 37:15–30. https://doi.org/10.1016/j.jes.2015.04.011
Jin C, Han S, Li J, Sun Q (2015) Fabrication of cellulose-based aerogels from waste newspaper without any pretreatment and their use for absorbents. Carbohydr Polym 123:150–156. https://doi.org/10.1016/j.carbpol.2015.01.056
Karzar Jeddi M, Laitinen O, Liimatainen H (2019) Magnetic superabsorbents based on nanocellulose aerobeads for selective removal of oils and organic solvents. Mater Des 183:108115. https://doi.org/10.1016/j.matdes.2019.108115
Kujawinski EB, Kido Soule MC, Valentine DL et al (2011) Fate of dispersants associated with the deepwater horizon oil spill. Environ Sci Technol 45:1298–1306. https://doi.org/10.1021/es103838p
Kulal DK, Khose RV, Pethsangave DA et al (2019) Biomass-derived lignocellulosic graphene composite: novel approach for removal of oil and organic solvent. ChemistrySelect 4:4568–4574. https://doi.org/10.1002/slct.201900115
Kumar V, Verma R (2023) Effect of GNP and laser-surface texturing on HVOF sprayed WC10Co4Cr coatings for high-wear resistance. Tribol Int 178:108057. https://doi.org/10.1016/j.triboint.2022.108057
Kumar D, Wu X, Fu Q et al (2015) Hydrophobic sol–gel coatings based on polydimethylsiloxane for self-cleaning applications. Mater Des 86:855–862. https://doi.org/10.1016/j.matdes.2015.07.174
Laitinen O, Suopajärvi T, Österberg M, Liimatainen H (2017) Hydrophobic, superabsorbing aerogels from choline chloride-based deep eutectic solvent pretreated and silylated cellulose nanofibrils for selective oil removal. ACS Appl Mater Interfaces 9:25029–25037. https://doi.org/10.1021/acsami.7b06304
Lavoine N, Desloges I, Dufresne A, Bras J (2012) Microfibrillated cellulose – Its barrier properties and applications in cellulosic materials: A review. Carbohydr Polym 90:735–764. https://doi.org/10.1016/j.carbpol.2012.05.026
Li Z, Wang B, Qin X et al (2018) Superhydrophobic/superoleophilic polycarbonate/carbon nanotubes porous monolith for selective oil adsorption from water. ACS Sustain Chem Eng 6:13747–13755. https://doi.org/10.1021/acssuschemeng.8b01637
Liu H, Geng B, Chen Y, Wang H (2017) Review on the aerogel-type oil sorbents derived from nanocellulose. ACS Sustain Chem Eng 5:49–66. https://doi.org/10.1021/acssuschemeng.6b02301
Long L-Y, Weng Y-X, Wang Y-Z (2018) Cellulose Aerogels: Synthesis, Applications, and Prospects. Polymers (Basel) 10:. https://doi.org/10.3390/polym10060623
Lü X, Cui Z, Wei W et al (2016) Constructing polyurethane sponge modified with silica/graphene oxide nanohybrids as a ternary sorbent. Chem Eng J 284:478–486. https://doi.org/10.1016/j.cej.2015.09.002
Lv N, Wang X, Peng S et al (2018) Superhydrophobic/superoleophilic cotton-oil absorbent: preparation and its application in oil/water separation. RSC Adv 8:30257–30264. https://doi.org/10.1039/C8RA05420G
Lv X, Qin Y, Liang H et al (2021) A facile method for constructing a superhydrophobic zinc coating on a steel surface with anti-corrosion and drag-reduction properties. Appl Surf Sci 562:150192. https://doi.org/10.1016/j.apsusc.2021.150192
Makowski T (2020) Hydrophobization of cotton fabric with silanes with different substituents. Cellulose 27:1–9. https://doi.org/10.1007/s10570-019-02776-4
Manoharan K, Anwar MT, Bhattacharya S (2021) Development of hydrophobic paper substrates using silane and sol–gel based processes and deriving the best coating technique using machine learning strategies. Sci Rep 11:11352. https://doi.org/10.1038/s41598-021-90855-7
Mata A, Fleischman AJ, Roy S (2005) Characterization of polydimethylsiloxane (PDMS) properties for biomedical micro/nanosystems. Biomed Microdevices 7:281–293. https://doi.org/10.1007/s10544-005-6070-2
Nguyen ST, Feng J, Le NT et al (2013) Cellulose aerogel from paper waste for crude oil spill cleaning. Ind Eng Chem Res 52:18386–18391. https://doi.org/10.1021/ie4032567
Nyström D, Lindqvist J, Östmark E et al (2009) Superhydrophobic and self-cleaning bio-fiber surfaces via ATRP and subsequent postfunctionalization. ACS Appl Mater Interfaces 1:816–823. https://doi.org/10.1021/am800235e
Parvinzadeh M, Ebrahimi I (2011) Influence of atmospheric-air plasma on the coating of a nonionic lubricating agent on polyester fiber. Radiat Eff Defects Solids 166:408–416. https://doi.org/10.1080/10420150.2011.553230
Paulauskiene T, Uebe J, Karasu AU, Anne O (2020) Investigation of cellulose-based aerogels for oil spill removal. Water Air Soil Pollut 231:424. https://doi.org/10.1007/s11270-020-04799-1
Payne KC, Jackson CD, Aizpurua CE et al (2012) Oil spills abatement: factors affecting oil uptake by cellulosic fibers. Environ Sci Technol 46:7725–7730. https://doi.org/10.1021/es3015524
Prathap A, Sureshan KM (2017) Organogelator-cellulose composite for practical and eco-friendly marine oil-spill recovery. Angew Chem Int Ed 56:9405–9409. https://doi.org/10.1002/anie.201704699
Radetić MM, Jocić DM, Jovančić PM et al (2003) Recycled wool-based nonwoven material as an oil sorbent. Environ Sci Technol 37:1008–1012. https://doi.org/10.1021/es0201303
Radhakrishnan J, Diaz M, Cordovilla F et al (2023) Water droplets impact dynamics on laser engineered superhydrophobic ceramic surface. Opt Laser Technol 158:108887. https://doi.org/10.1016/j.optlastec.2022.108887
Report (2021) Oil 2021 - Analysis and forecast to 2026
Rong W, Zhang H, Mao Z et al (2021) Stable drag reduction of anisotropic superhydrophobic/hydrophilic surfaces containing bioinspired micro/nanostructured arrays by laser ablation. Colloids Surf A Physicochem Eng Asp 622:126712. https://doi.org/10.1016/j.colsurfa.2021.126712
Satyarathi J, Kumar V, Kango S et al (2022) Comparative study of fabricated superhydrophobic surfaces via LST with carbon soot, chemical etching and auto-oxidation. Surf Topogr 10:045017. https://doi.org/10.1088/2051-672X/ac9c76
Schaum J, Cohen M, Perry S et al (2010) Screening level assessment of risks due to dioxin emissions from burning oil from the bp deepwater horizon gulf of mexico spill. Environ Sci Technol 44:9383–9389. https://doi.org/10.1021/es103559w
SDWF (2017) Oil Spills Fact Sheet. https://www.safewater.org/fact-sheets-1/2017/1/23/oil-spills. Accessed 9 Sep 2023
Shang Q, Chen J, Liu C et al (2019) Facile fabrication of environmentally friendly bio-based superhydrophobic surfaces via UV-polymerization for self-cleaning and high efficient oil/water separation. Prog Org Coat 137:105346. https://doi.org/10.1016/j.porgcoat.2019.105346
Sharma DK, Baghel V, Kumar R et al (2019) Recent developments in fabrication of super-hydrophobic surfaces: a review. Lect Notes Mech Eng 127–140. https://doi.org/10.1007/978-981-13-6412-9_12
Sharma DK, Kumar R, Avasthi DK, Sikarwar BS (2020) Self assembly of super-hydrophobic nanotextured methyl functionalized silica on copper and aluminium surfaces for moist air condensation. Colloids Surfaces A Physicochem Eng Asp 605:125379. https://doi.org/10.1016/j.colsurfa.2020.125379
Sharma DK, Sikarwar BS, Upadhyay S et al (2022) Super-hydrophobic nanostructured silica coating on aluminum substrate for moist air condensation. J Mater Eng Perform 31:1266–1276. https://doi.org/10.1007/s11665-021-06254-6
Singh V, Kendall RJ, Hake K, Ramkumar S (2013) Crude oil sorption by raw cotton. Ind Eng Chem Res 52:6277–6281. https://doi.org/10.1021/ie4005942
Singhal S, Agarwal S, Kumar A et al (2023) Waste clothes to microcrystalline cellulose: an experimental investigation. J Polym Environ 31:358–372. https://doi.org/10.1007/s10924-022-02609-9
Tudu BK, Sinhamahapatra A, Kumar A (2020) Surface modification of cotton fabric using TiO2 nanoparticles for self-cleaning, oil-water separation, antistain, anti-water absorption, and antibacterial properties. ACS Omega 5:7850–7860. https://doi.org/10.1021/acsomega.9b04067
Ukpong A, Habor G, Oboh I (2020) Adsorption studies of oil spill cleanup using coconut coir activated carbon (CCAC). The Open Chem Eng J 8:36–47. https://doi.org/10.11648/j.ajche.20200802.11
Viju S, Brindha R, Thilagavathi G (2019) Surface modification of nettle fibers by grafting to improve oil sorption capacity. J Ind Text 50:1314–1329. https://doi.org/10.1177/1528083719862879
Wang B, Liang W, Guo Z, Liu W (2015) Biomimetic super-lyophobic and super-lyophilic materials applied for oil/water separation: a new strategy beyond nature. Chem Soc Rev 44:336–361. https://doi.org/10.1039/C4CS00220B
Wang Y, Zhang Z, Xu J, Yu H (2021) One-step method using laser for large-scale preparation of bionic superhydrophobic & drag-reducing fish-scale surface. Surf Coat Technol 409:126801. https://doi.org/10.1016/j.surfcoat.2020.126801
Wei X-L, Li N, Yi WJ et al (2017) High performance super-hydrophobic ZrO2-SiO2 porous ceramics coating with flower-like CeO2 micro/nano-structure. Surf Coat Technol 325:565–571. https://doi.org/10.1016/j.surfcoat.2017.06.004
Woo-hyun Park, Ho Seo-gwan, Woong-han Kim (2008) Water repellent coating composition for treating the glass substrates and method for the preparation
Xia T, Yuwen H, Lin N (2018) Self-bonding sandwiched membranes from PDMS and cellulose nanocrystals by engineering strategy of layer-by-layer curing. Compos Sci Technol 161:8–15. https://doi.org/10.1016/j.compscitech.2018.03.038
Xiang Y, Pang Y, Jiang X et al (2018) One-step fabrication of novel superhydrophobic and superoleophilic sponge with outstanding absorbency and flame-retardancy for the selective removal of oily organic solvent from water. Appl Surf Sci 428:338–347. https://doi.org/10.1016/j.apsusc.2017.09.093
Yan L, Li P, Zhou W et al (2019) Shrimp shell-inspired antifouling chitin nanofibrous membrane for efficient oil/water emulsion separation with in situ removal of heavy metal ions. ACS Sustain Chem Eng 7:2064–2072. https://doi.org/10.1021/acssuschemeng.8b04511
Yu H, Lian Z, Wan Y et al (2015) Fabrication of durable superamphiphobic aluminum alloy surfaces with anisotropic sliding by HS-WEDM and solution immersion processes. Surf Coat Technol 275:112–119. https://doi.org/10.1016/j.surfcoat.2015.05.032
Zhang J, Seeger S (2011) Polyester materials with superwetting silicone nanofilaments for oil/water separation and selective oil absorption. Adv Funct Mater 21:4699–4704. https://doi.org/10.1002/adfm.201101090
Zhang S, Wang W-C, Li F-X, Yu J-Y (2013) Swelling and dissolution of cellulose in NaOH aqueous solvent systems. Cellul Chem Technol 47:671–679
Zhang X, Wang F, Keer LM (2015) Influence of surface modification on the microstructure and thermo-mechanical properties of bamboo fibers. Materials 8:6597–6608. https://doi.org/10.3390/ma8105327
Zheng S, Bellido-Aguilar DA, Huang Y et al (2019) Mechanically robust hydrophobic bio-based epoxy coatings for anti-corrosion application. Surf Coat Technol 363:43–50. https://doi.org/10.1016/j.surfcoat.2019.02.020
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
Conflict of interest
On behalf of all authors, the corresponding author states that there is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Bhardwaj, J., Gupta, R.K., Agarwal, S. et al. Waste-derived cellulose-based hydrophobic matrix for efficient oil–water separation: a sustainable approach to mitigate aquatic environmental disasters. Chem. Pap. 78, 3175–3188 (2024). https://doi.org/10.1007/s11696-024-03302-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11696-024-03302-y