The volume fraction of reinforcement and milling time are two important factors in fabricating aluminum metal matrix composites via powder metallurgy (P/M) techniques. In the present work, the effects of volume fraction of reinforcement and milling time on the microstructure, relative density, hardness, and compressive strength were studied. The Al7075 and SiC powders were mixed by a planetary ball mill for about 4 and 8 h, and Al7075–x vol.% SiC specimens (x = 4, 6, 8) were fabricated by a uniaxial cold press and sintered at 873 K (600°C) for 1 h. The crystallite size and morphology of the powder particles were analyzed with X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results showed that with increasing milling time and volume fraction of the reinforcement phase, the hardness and compressive strength increased. The SEM illustrates that the number of voids increases as SiC content increases, but their size decreases.
Similar content being viewed by others
References
A. Azimi, A. Shokuhfar, and O. Nejadseyfi, “Mechanically alloyed Al7075–TiC nanocomposite: Powder processing, consolidation and mechanical strength,” Mater. Des., 66, Part A, 137–141 (2015).
H. R. Hafizpour and A. Simchi, “Investigation on compressibility of Al–SiC composite powders,” Powder Metall., Vol. 51, No. 3, 217–223 (2008).
M. A. Jabbari Taleghani, E. M. Ruiz Navas, and J. M. Torralba, “Microstructural and mechanical characterization of 7075 aluminum alloy consolidated from a premixed powder by cold compaction and hot extrusion,” Mater. Des., 55, 674–682 (2014).
Y. Jia, F. Cao, Z. Ning, et al., “Influence of second phases on mechanical properties of spray-deposited Al–Zn–Mg–Cu alloy,” Mater. Des., 40, 536–540 (2012).
S. Kamrani, A. Simchi, R. Riedel, and S. M. Seyed Reihani, “Effect of reinforcement volume fraction on mechanical alloying of Al–SiC nanocomposite powders,” Powder Metall., 50, No. 3, 276–282 (2007).
M. A. Mobarhan Bonab and A. Simchi, “Effect of silicon carbide nanoparticles on hot deformation of ultrafine-grained aluminum nanocomposites prepared by hot powder extrusion process,” Powder Metall., 59, No. 4, 262–270 (2016).
Z. G. Wang, C. P. Li, H. Y. Wang, et al., “Effect of nano-SiC content on mechanical properties of SiC/2014Al composites fabricated by powder metallurgy combined with hot extrusion,” Powder Metall., 59, No. 4, 236–241 (2016).
G. B. Schaffer and S. H. Huo, “On development of sintered 7xxx series aluminum alloys,” Powder Metall., Vol. 42, No. 3, 219–226 (1999).
A. A. El-Daly, M. Abdelhameed, M. Hashish, and W. M. Daoush, “Fabrication of silicon carbide reinforced aluminum matrix nanocomposites and characterization of its mechanical properties using nondestructive technique,” Mater. Sci. Eng. A., 559, 384–393 (2013).
M. O. Bodunrin, K. K. Alaneme, and L. H. Chown, “Aluminum matrix hybrid composites: a review of reinforcement philosophies; mechanical, corrosion and tribological characteristics,” J. Mater. Res. Technol., No. 4, 434–445 (2015).
R. Senthilkumar, N. Arunkumar, and M. Manzoor Hussian, “A comparative study on low cycle fatigue behavior of nano and micro Al2O3 reinforced AA2014 particulate hybrid composites,” Results Phys., 5, 273–280 (2015).
O. El-Kady and A. Fathy, “Effect of SiC particle size on the physical and mechanical properties of extruded Al matrix nanocomposites,” Mater. Des., 54, 348–353 (2014).
A. Abdollahi, A. Alizadeh, and H. R. Baharvandi, “Dry sliding tribological behavior and mechanical properties of Al2024–5 wt.% B4C nanocomposite produced by mechanical milling and hot extrusion,” Mater. Des., 55, 471–481 (2014).
M. Khademian, A. Alizadeh, and A. Abdollahi, “Fabrication and characterization of hot rolled and hot extruded boron carbide (B4C) reinforced A356 aluminum alloy matrix composites produced by stir casting method,” Trans. Indian Inst. Met., 1–12 (2016).
M. Rahimian, N. Ehsani, N. Parvin, and H. R. Baharvandi, “The effect of sintering temperature and the amount of reinforcement on the properties of Al–Al2O3 composite,” Mater. Des., 30, No. 8, 3333–3337 (2009).
M. Rahimian, N. Ehsani, N. Parvin, and H. R. Baharvandi, “The effect of particle size, sintering temperature and sintering time on the properties of Al–Al2O3 composites, made by powder metallurgy,” J. Mater. Process. Technol., 209, No. 14, 5387–5393 (2009).
S. S. Razavi-Tousi, R. Yazdani-Rad, and S. A. Manafi, “Effect of volume fraction and particle size of alumina reinforcement on compaction and densification behavior of Al–Al2O3 nanocomposites,” Mater. Sci. Eng. A., 528, No. 3, 1105–1110 (2011).
Z. Wei, P. Ma, H. Wang, et al. “The thermal expansion behaviour of SiCp/Al–20Si composites solidified under high pressures,” Mater. Des., 65, 387–394 (2015).
H. Asgharzadeh, “Sintering behavior of nanocrystalline Al6063 powders prepared by high-energy mechanical milling,” Trans. Indian Inst. Met., 69, No. 7, 1359–1368 (2016).
P. Van Trinh, N. Van Luan, P. N. Minh, and D. D. Phuong, “Effect of sintering temperature on properties of CNT/Al composite prepared by capsule-free hot isostatic pressing technique, 69, No. 7, 1–9 (2016).
A. Alizadeh, and E. Taheri-Nassaj, “Mechanical properties and wear behavior of Al–2 wt.% Cu alloy composites reinforced by B4C nanoparticles and fabricated by mechanical milling and hot extrusion,” Mater. Charact., 67, 119–128 (2012).
H. Ghasemi Yazdabadi, A. Ekrami, H. S. Kim, and A. Simchi, “An investigation on the fatigue fracture of P/M Al–SiC nanocomposites,” Metall. Mater. Trans. A., 44, No. 6, 2662–2671 (2013).
C. Suryanarayana, “Mechanical alloying and milling,” Prog. Mater. Sci., 46, Nos. 1–2, 1–184 (2001).
C. Suryanarayana, E. Ivanov, and V. V. Boldyrev, “The science and technology of mechanical alloying,” Mater. Sci. Eng. A., 304–306, 151–158 (2001).
D. L. Zhang, “Processing of advanced materials using high-energy mechanical milling,” Prog. Mater. Sci., 79, Nos. 3–4, 537–560 (2004).
H. Simchi and A. Simchi, “Tensile and fatigue fracture of nanometric alumina reinforced copper with bimodal grain size distribution,” Mater. Sci. Eng. A., 507, Nos. 1–2, 200–206 (2009).
F. Chen, Z. Chen, F. Mao, et al., “TiB2 reinforced aluminum based in situ composites fabricated by stir casting,” Mater. Sci. Eng. A., 625, 357–368 (2015).
T. Wang, Z. Chen, Y. Zheng, et al., “Development of TiB2 reinforced aluminum foundry alloy based in situ composites. Part II: Enhancing the practical aluminum foundry alloys using the improved Al–5 wt.% TiB2 master composite upon dilution,” Mater. Sci. Eng. A., 605, 22–32 (2014).
S. Sattari and A. Atrian, “Effects of the deep rolling process on the surface roughness and properties of an Al−3 vol.% SiC nanoparticle nanocomposite fabricated by mechanical milling and hot extrusion,” Int. J. Minerals, Metallurgy, Materials,” 24, Issue 7, 814–825 (2017).
S. Sattari and M. Jahani, “An investigation of parameters involved and defects in the fabrication of Al–SiC nanocomposite using hot extrusion technique,” Transac. Indian Inst. Metals., DOI: 10.1007/s12666-017-1097-7, 1–10 (2017).
Author information
Authors and Affiliations
Corresponding author
Additional information
Published in Poroshkovaya Metallurgiya, Vol. 56, Nos. 5–6 (515), pp. 60–71, 2017.
Rights and permissions
About this article
Cite this article
Sattari, S., Jahani, M. & Atrian, A. Effect of Volume Fraction of Reinforcement and Milling Time on Physical and Mechanical Properties of Al7075–SiC Composites Fabricated by Powder Metallurgy Method. Powder Metall Met Ceram 56, 283–292 (2017). https://doi.org/10.1007/s11106-017-9896-2
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11106-017-9896-2