Skip to main content
SpringerLink
Log in

The Influence of Specific Features of Load and Hydrogen Charging on Steel Tribotechnical Properties

  • Published:
Materials Science Aims and scope

Wear resistance of structural steels 20 and 45 and high-nitrogen steel DDT68 during dry friction under different load conditions was studied. With an increase in slip to 20% at a load of 550 N the wear intensity increases 1.41 times for high-nitrogen steel and 1.54 times for structural steel. During sliding the surface fractures by tearing of the material under intense thermal setting, which affects the formation of secondary structures with increased oxygen concentration. With the reliability approximation of R2 = 0.87 – 0.99 logarithmic and polynomial equations which describe the wear intensity in the conditions of slip and loading changes for the studied steels are obtained. After hydrogen charging the wear products have a significantly more complex textured microrelief with strips and larger sizes: ≥ 350 μm (P = 250N), 600 – 1000 μm (P = 400N), 800 – 1300 μm (P = 600N).

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.

Similar content being viewed by others

References

  1. H. Lin, M. Yang, and B. Shu, “Fretting wear behaviour of high-nitrogen stainless bearing steel under lubrication condition,” J. of Iron and Steel Res. Int., 27, Is. 7, 849–866 (2020); https://doi.org/10.1007/s42243-020-00414-z.

  2. S. V. Rashev, A. V. Eliseev, L. Ts. Zhekova, and P. V. Bogev, “High-nitrogen steel,” Steel in Translation, 49, Is. 7, 433–439 (2019); https://doi.org/10.3103/S0967091219070106.

  3. A. Upadhye, N. Shah, P. K. Lalge, N. Dhokey, and T. Tharian, “Evolution of ultrafine precipitates and its influence on wear mechanism in cryoprocessed high nitrogen martensitic steel,” Tribology – Mater. Surf. & Interfaces, 13, Is. 4, 233–229 (2019); https://doi.org/10.1080/17515831.2019.1656908.

  4. V. V. Kulyk, S. Ya. Shipitsyn, O. P. Ostash, Z. A. Duriagina, and V. V. Vira, “The joint effect of vanadium and nitrogen on the mechanical behavior of railroad wheels steel,” J. of Achiev. in Mater. and Manufact. Eng., 89, Is. 2, 56–63 (2018); https://doi.org/10.5604/01.3001.0012.7109.

  5. O. I. Balyts’kyi, and V. O. Kolesnikov, “Investigation of wear products of high-nitrogen manganese steels,” Mater. Sci., 45, No. 4, 576–581 (2009); https://doi.org/10.1007/s11003-010-9216-1.

  6. O. I. Balyts’kyi, V. O. Kolesnikov, and J. Eliasz, “Study of the wear resistance of high-nitrogen steels under dry sliding friction,” Mater. Sci., 48, No. 5, 642–646 (2013); https://doi.org/10.1007/s11003-013-9549-7.

  7. O. I. Balyts’kyi, V. O. Kolesnikov, J. Eliasz, M. R. Havrylyuk, “Specific features of the fracture of hydrogenated high-nitrogen manganese steels under conditions of rolling friction,” Mater. Sci., 50, No. 4, 604–611 (2015); https://doi.org/10.1007/s11003-015-9760-9.

  8. Y.-S. Lee, S. Yamagishi, M. Tsuro, C. Ji, S. Cho, Y. Kim, and M. Choi, “Wear behaviors of stainless steel and lubrication effect on transitions in lubrication regimes in sliding contact,” Metals, 11, Is. 11, Article number: 1854, (2021); https://doi.org/10.3390/met11111854.

  9. W. W. Seifert, and W. C. Westcott, “A method for the study of wear particles in lubricating oil,” Wear, 21, Is. 1, 27–42 (1972); https://doi.org/10.1016/0043-1648(72)90247-5.

  10. I. M. Dmytrakh, R. L. Leshchak, and A. M. Syrotyuk, “Experimental study of low concentration diffusible hydrogen effect on mechanical behaviour of carbon steel,” Struct. Integrity, 16, 32–37 (2020); https://doi.org/10.1007/978-3-030-47883-4_6.

  11. V. I. Tkachev, L. M. Ivaskevich, and I. M. Levina, “Distinctive features of hydrogen degradation of heat-resistant alloys based on nickel,” Mater. Sci., 33, No. 4, 524–531 (1997); https://doi.org/10.1007/BF02537549.

    Article  CAS  Google Scholar 

  12. V. Hutsaylyuk, M. Student, V. Dovhunyk, V. Posuvailo, O. Student, P. Maruschak, and I. Koval’chuck, “Effect of hydrogen on the wear resistance of steels upon contact with plasma electrolytic oxidation layers synthesized on aluminum alloys,” Metals, 9, Is. 3, Article number: 280 (2019); https://doi.org/10.3390/met9030280.

  13. A. I. Balitskii, and L. M. Ivaskevich, “Assessment of hydrogen embrittlement in high-alloy chromium-nickel steels and alloys in hydrogen at high pressures and temperatures,” Strength Mater., 50, No. 6, 880–887 (2018); https://doi.org/10.1007/s11223-019-00035-2.

    Article  CAS  Google Scholar 

  14. I. G. Slys, V. I. Berezanskaya, I. A. Kossko, and A. P. Pomytkin, “Development of new corrosion-resistant and wear-resistant materials for use in agressive hydrogen medium,” Int. J. of Hydrogen Energy, 26, Is. 5, 531–536 (2001); https://doi.org/10.1016/S0360-3199(00)00087-2.

  15. Yu. I. Osenin, I. I. Sosnov, A. V. Chesnokov, L. I. Antoshkina, and Yu. Yu. Osenin, “Friction unit of a disc brake based on a combination of friction materials,” J. of Friction and Wear, 40, Is. 4, 293–296 (2019); https://doi.org/10.3103/S1068366619040093.

  16. V. I. Pokhmurs’kyi, and Kh. B. Vasyliv, “Influence of hydrogen on the friction and wear of metals (a survey),” Mater. Sci., 48, No. 2, 125–138 (2012); https://doi.org/10.1007/s11003-012-9482-1.

  17. D. Banks, and P. Clayton, “Comparison of the wear process for eutectoid rail steels: field and laboratory tests,” Wear, 120, 233–250 (1987); https://doi.org/10.1016/0043-1648(87)90069-X.

  18. P. Clayton, “Predicting the wear of rails on curves from laboratory data. Part 1,” Wear, 181–183, 11–19 (1995); https://doi.org/10.1016/0043-1648(95)90003-9.

  19. B. K. Prasad, “Sliding wear response of spheroidal graphite cast iron as influenced by applied pressure, sliding speed and test environment,” Canadian Metallurgical Quarterly, 47, Is. 4, 495–508 (2008); https://doi.org/10.1179/cmq.2008.47.4.495.

  20. M. B. Djukic, G. M. Bakic, Z. V. Sijacki, A. Sedmak, and B. Rajicic, “The synergistic action and interplay of hydrogen embrittlement mechanisms in steels and iron: localized plasticity and decohesion,” Eng. Fract. Mech., 216, Article number: 106528 (2019); https://doi.org/10.1016/j.engfracmech.2019.106528.

  21. O. P. Datsyshyn, V. V. Panasyuk, and A. Glazov, “Modeling of fatigue contact damages formation in rolling bodies and assessment of their lifetime,” Wear, 271, Is. 1–2, 186–194 (2011); https://doi.org/10.1016/j.wear.2010.10.023.

  22. O. Barrera, D. Bombac, Y. Chen, T. D. Daff, E. Galindo-Nava, P. Gong, D. Haley, R. Horton, I. Katzarov, J. R. Kermode, C. Liverani, M. Stopher, and F. Sweeney, “Understanding and mitigating hydrogen embrittlement of steels: a review of experimental, modelling and design progress from atomistic to continuum,” J. of Mater. Sci., 53, Is. 9, 6251–6290 (2018); https://doi.org/10.1007/s10853-017-1978-5.

  23. M. Dadfarnia, A. Nagao, S. Wang, and M. L. Martin, “Recent advances on hydrogen embrittlement of structural materials,” Int. J. of Fract., 196, Is. 1–2, 223–243 (2015); https://doi.org/10.1007/s10704-015-0068-4.

  24. S. Lynch, “Hydrogen embrittlement phenomena and mechanisms,” Corr. Rev., 30, Is. 3–4, 105–123 (2012); https://doi.org/10.1515/corrrev-2012-0502.

  25. L. R. Queiroga, G. F. Marcolino, M. Santos, G. Rodrigues, C. E. dos Santos, and P. Brito, “Influence of machining parameters on surface roughness and susceptibility to hydrogen embrittlement of austenitic stainless steels,” Int. J. of Hydrogen Energy, 44, Is. 54, 29027–29033 (2019); https://doi.org/10.1016/j.ijhydene.2019.09.139.

  26. V. N. Kulkarni, V. K. Jain, and A. K. Shukla, “Measurement of hydrogen content in electrical discharge machined components,” Machining Sci. and Tech. An Int. J., 9, Is. 2, 289–299 (2005); https://doi.org/10.1081/MST-200059070.

  27. T. Michler, and J. Naumann, “Hydrogen embrittlement of Cr–Mn–N-austenitic stainless steels,” Int. J. of Hydrogen Energy, 35, Is. 3, 1485–1492 (2010); https://doi.org/10.1016/j.ijhydene.2009.10.050.

  28. A. I. Balitskii, L. M. Ivaskevich, V. M. Mochulskyi, J. Eliasz, and O. Skolozdra, “Influence of high pressure and high temperature hydrogen on fracture toughness of Ni-containing steels and alloys,” Arch. of Mech. Eng., 61, Is. 1, 129–138 (2014); https://doi.org/10.2478/meceng-2014-0007.

  29. M. H. Stashchuk, and M. Dorosh, “Evaluation of hydrogen stresses in metal and redistribution of hydrogen around crack-like defects,” Int. J. of Hydrogen Energy, 37, Is. 19, 14687–14696 (2012); https://doi.org/10.1016/j.ijhydene.2012.07.093.

  30. V. V. Panasyuk, Ya. L. Ivanyts’kyi, O. V. Hembara, and V. M. Boiko, “Influence of the stress-strain state on the distribution of hydrogen concentration in the process zone,” Mater. Sci., 50, No. 3, 315–323 (2014); https://doi.org/10.1007/s11003-014-9723-6.

  31. I. Dmytrakh, A. Syrotyuk, and R. Leshchak, “Specific mechanism of hydrogen influence on deformability and fracture of lowalloyed pipeline steel,” Proc. Struct. Integrity, 36, 298–305 (2022); https://doi.org/10.1016/j.prostr.2022.01.038.

  32. J. Capelle, J. Gilgert, I. Dmytrakh, and G. Pluvinage, “The effect of hydrogen concentration on fracture of pipeline steels in presence of a notch,” Eng. Fract. Mech., 78, Is. 2, 364–373 (2011); https://doi.org/10.1016/j.engfracmech.2010.10.007.

Download references

Author information

Authors and Affiliations

  1. Karpenko Physicomechanical Institute, National Academy of Sciences of Ukraine, Lviv, Ukraine

    O. I. Balitskii, V. O. Kolesnikov, L. M. Ivaskevych & M. R. Havrylyuk

  2. West Pomeranian University of Technology, Szczecin, Poland

    O. I. Balitskii

  3. Taras Shevchenko National University of Luhansk, Poltava, Ukraine

    V. O. Kolesnikov

Authors
  1. O. I. Balitskii
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. V. O. Kolesnikov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. L. M. Ivaskevych
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. M. R. Havrylyuk
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to O. I. Balitskii.

Additional information

Translated from Fizyko-Khimichna Mekhanika Materialiv, Vol. 58, No. 4, pp. 73–80, July–August, 2022.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Balitskii, O.I., Kolesnikov, V.O., Ivaskevych, L.M. et al. The Influence of Specific Features of Load and Hydrogen Charging on Steel Tribotechnical Properties. Mater Sci 58, 505–512 (2023). https://doi.org/10.1007/s11003-023-00691-5

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11003-023-00691-5

Keywords

Search

Navigation