Skip to main content
SpringerLink
Log in

Role of oxalic acid in structural formation of sodium silicate-based silica aerogel by ambient pressure drying

  • Original Paper: Fundamentals of sol-gel and hybrid materials processing
  • Published:
Journal of Sol-Gel Science and Technology Aims and scope Submit manuscript

Abstract

Recently, the demand of sodium silicate-based silica aerogels has decreased due to its inadequate physical properties when compared to those made by other silicon alkoxides. To avoid this problem, introduction of a drying control chemical additive (DCCA) in the sol has received great attention. DCCA is one of the additives that can control the rate of hydrolysis and the condensation reaction in sol state by the formation of hydrogen bonds between DCCA and silanol groups of silica sol. A control over these reactions results in a uniform pore size distribution, which, in turn, decreases the drying stress with a decrease in pore size, in accordance with the Young–Laplace equation. Therefore, the structure of the silica aerogel can be maintained by minimizing the volume shrinkage due to drying stress. In this research, oxalic acid was first used as DCCA in the formation of sodium silicate-based silica aerogel by ambient pressure drying. The physical properties of these silica aerogels can be changed by changing the molar ratio of oxalic acid/Na2SiO3 in the sol state. When the oxalic acid:Na2SiO3 molar ratio was 15 × 10−4 in the sol state, aerogels with high specific surface area (623.2 m2/g), pore volume (4.271 cm3/g), average pore diameter (27.41 nm), high porosity (94.3%), high contact angle (144.09°), and high optical transmittance (75%) were obtained.

Graphical abstract

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9

Similar content being viewed by others

References

  1. Dorcheh AS, Abbasi MH (2008) Silica aerogel; synthesis, properties and characterization. J Mater Process Technol 199(1–3):10–26

    Article  Google Scholar 

  2. Schmidt M, Schwertfeger F (1998) Applications for silica aerogel products. J Non Cryst Solids 225:364–368

    Article  Google Scholar 

  3. Parale VG, Mahadik DB, Kavale MS, Rao AV, Wagh PV, Gupta SC (2011) Potential application of silica aerogel granules for cleanup of accidental spillage of various organic liquids. Soft Nanosci Lett 1:97–104

    Article  Google Scholar 

  4. Parale VG, Lee KY, Park HH (2017) Flexible and transparent silica aerogels: an overview. J Korean Ceram Soc 54(3):184–199

    Article  Google Scholar 

  5. Zhou H, Wang X, Liu H, Yan M (2017) Enhanced hydrogen storage properties of 2LiBH4-LiAlH4 nanoconfined in resorcinol formaldehyde carbon aerogel. J Alloy Compd 726:525–531

    Article  Google Scholar 

  6. Kim SJ, Jana SC (2017) Effects of skin layers on air permeability in macroporous polymer aerogels. Polymer 126:432–436

    Article  Google Scholar 

  7. Haddad N, Ayadi ZB, Djessas K (2017) Synthesis and characterization of antimony doped tin oxide aerogel nanoparticles using a facile sol-gel method. J Mater Sci Mater Electron: 1–9. https://doi.org/10.1007/s10854-017-7965-4

  8. Hammiche L, Slimi O, Djouadi D, Chelouche A, Touam T (2017) Effect of supercritical organic solvent on structural and optical properties of cerium doped zinc oxide aerogel nanoparticles. Optik 145:448–455

    Article  Google Scholar 

  9. Sorour M, Hani HA, Al-Bazedi GA, El-Rafei AM (2016) Hydrophobic silica aerogels for oil spills clean-up, synthesis, characterization and preliminary performance evaluation. J Porous Mater 23:1401–1409

    Article  Google Scholar 

  10. Shao Z, He X, Niu Z, Huang T, Cheng X, Zhang Y (2015) Ambient pressure dried shape-controllable sodium silicate based composite silica aerogel monoliths. Mater Chem Phys 162:346–353

    Article  Google Scholar 

  11. Aegerter MA, Leventis N, Koebel M (2011) Aerogels handbook. Springer, New York

    Book  Google Scholar 

  12. Gurav JL, Rao AV, Rao AP, Nadargi DY, Bhagat SD (2009) Physical properties of sodium silicate based aerogels prepared by single step sol-gel process dried at ambient pressure. J Alloy Compd 476(1–2):397–402

    Article  Google Scholar 

  13. Bhagat SD, Kim YH, Suh KH, Ahn YS, Yeo JG, Han JH (2008) Superhydrophobic silica aerogel powders with simultaneous surface modification, solvent exchange and sodium ion removal from hydrogels. Microporous Mesoporous Mater 112(1–3):504–509

    Article  Google Scholar 

  14. Bangi UKH, Kavale MS, Baek S, Park HH (2012) Synthesis of MWCNTs doped sodium silicate based aerogels by ambient pressure drying. J Sol-Gel Sci Technol 62(2):201–207

    Article  Google Scholar 

  15. Bhagat SD, Kim HY, Ahn YS, Yeo JG (2006) Textural properties of ambient pressure dried water-glass based silica aerogel beads: one day synthesis. Microporous Mesoporous Mater 96(1–3):237–244

    Article  Google Scholar 

  16. Shi F, Wang L, Liu J (2006) Synthesis and characterization of silica aerogels by a novel fast ambient pressure drying process. Mater Lett 60(29–30):2718–3722

    Article  Google Scholar 

  17. Rao AV, Rao AP, Kulkarni MM (2004) Influence of gel aging and Na2SiO3/H2O molar ratio on monolithicity and physical properties of water-glass-based aerogels dried at atmospheric pressure. J Non Cryst Solids 350:224–229

    Article  Google Scholar 

  18. Eiarsrud MA, Nilsen E, Rigacci A, Pajonk GM, Buathier S, Valette D, Durant M, Chevalier B, Nitz P, Ehrburger-Dolle F (2001) Strengthening of silica gels and aerogels by washing and aging processes. J Non Cryst Solids 285(1–3):1–7

    Article  Google Scholar 

  19. Suh DJ, Park TJ, Sonn JH, Lim JC (1999) Effect of aging on the porous texture of silica aerogels prepared by NH4OH and NH4F catalyzed sol-gel process. J Mater Sci Lett 18:1473–1475

    Article  Google Scholar 

  20. Karakuzu B, Temel TM, Yucel S, Terzioglu P, Elamis Y (2016) Effect of acid type and gelation pH on the structural properties of silica aerogels prepared by use of rice hull biosilica. Sig J Eng Nat Sci 34(2):175–182

    Google Scholar 

  21. Hwang SW, Kim TY, Hyun SH (2010) Effect of surface modification conditions on the synthesis of mesoporous crack-free silica aerogel monoliths from waterglass via ambient-drying. Microporous Mesoporous Mater 130(1–3):295–302

    Article  Google Scholar 

  22. Mahadik DB, Jung HNR, Han W, Cho HH, Park HH (2017) Flexible, elastic, and superhydrophobic silica-polymer composite aerogels by high internal phase emulsion process. Compos Sci Technol 147:45–51

    Article  Google Scholar 

  23. Cai L, Shan G (2015) Elastic silica aerogel using methyltrimethoxysilane precursor via ambient pressure drying. J Porous Mater 22:1455–1463

    Article  Google Scholar 

  24. Haranath D, Rao AV, Wagh PB (1999) Influence of DCCAs on optical transmittance and porosities of TMOS silica aerogels. J Porous Mat 6(1):55–62

    Article  Google Scholar 

  25. Rao AV, Kulkarni MM (2002) Effect of glycerol additive on physical properties of hydrophobic silica aerogels. Mater Chem Phys 77(3):819–825

    Article  Google Scholar 

  26. He S, Cheng X, Bi H, Yang H (2014) Synthesis and effect of DCCA on the ambient pressure dried, TEOS-based silica aerogel. Adv Mater Res 1044–1045:119–123

    Article  Google Scholar 

  27. Adachi T, Sakka S (1998) Sintering of silica gel derived from the alkoxysilane solution containing N,N-dimethylformamide. J Non Cryst Solids 100(1–3):250–253

    Article  Google Scholar 

  28. He S, Huang D, Bi H, Li Z, Yang H, Cheng X (2015) Synthesis and characterization of silica aerogels dried under ambient pressure bed on sodium silicate. J Non Cryst Solids 410:58–64

    Article  Google Scholar 

  29. Kim CE, Yoon JS, Hwang HJ (2009) Synthesis of nanoporous silica aerogel by ambient pressure drying. J Sol-Gel Sci Technol 49:47–52

    Article  Google Scholar 

  30. Bangi UKH, Jung IK, Park CS, Baek S, Park HH (2013) Optically transparent silica aerogels based on sodium silicate by a two step sol-gel process and ambient pressure drying, sol-gel method. Solid State Sci 18:50–57

    Article  Google Scholar 

  31. Dervin S, Lang Y, Perova T, Hinder SH, Pillai SC (2017) Graphene oxide reinforced high surface area silica aerogels. J Non Cryst Solids 465:31–38

    Article  Google Scholar 

  32. Yu Y, Guo D, Fang J (2015) Synthesis of silica aerogel microspheres by a two-step acid-base sol-gel reaction with emulsification technique. J Porous Mater 22:621–628

    Article  Google Scholar 

  33. Mahadik DB, Lee YK, Park CS, Chung HY, Hong MH, Jung HNR, Han W, Park HH (2015) Effect of water ethanol solvents mixture on textural and gas-sensing properties of tin oxide prepared using epoxide-assisted sol-gel process and dried at ambient pressure. Solid State Sci 50:1–8

    Article  Google Scholar 

  34. He S, Zhi L, Xiaojing S, Hui Y, Lunlun G, Xudong C (2015) Rapid synthesis of sodium silicate based hydrophobic silica aerogel granules with large surface area. Adv Powder Technol 26:537–541

    Article  Google Scholar 

  35. Parale VG, Mahadik DB, Mahadik SA, Kavale MS, Rao AV, Wagh PB (2012) Wettability study of surface modified silica aerogels with different silylating agents. J Sol-Gel Sci Technol 63(3):573–579

    Article  Google Scholar 

  36. Mahadik DB, Lee YK, Chavan NK, Mahadik SA, Park HH (2016) Monolithic and shrinkage-free hydrophobic silica aerogels via new rapid supercritical extraction process. J Supercrit Fluids 107:84–91

    Article  Google Scholar 

  37. Higgins J, Zhou X, Liu R, Huang TTS (1997) Theoretical study of thermal decomposition mechanism of oxalic acid. J Phys Chem A 101(14):2702–2708

    Article  Google Scholar 

  38. Wobbe DE, Noyes Jr. WA (1926) Photochemical studies. IV. The thermal decomposition of anhydrous oxalic acid and its relation to the photochemical decomposition. J Am Chem Soc 48:2856–2868

    Article  Google Scholar 

  39. Noyes Jr WA, Wobbe DE (1926) The vapor pressure of anhydrous oxalic acid. J Am Chem Soc 48(7):1882–1887

    Article  Google Scholar 

  40. Gumtya SK, Lahiri SC (2003) Ion-solvent interactions and determination of single-ion gibbs energies of transfer from the studies of the solubility and dissociation constants of oxalic acid in aquo + methanolic mixtures. Z Phys Chem 217(11):1341–1359

    Article  Google Scholar 

  41. Rao AP, Pajonk GM, Rao AV (2005) Effect of preparation conditions on the physical and hydrophobic properties of two step processed ambient pressure dried silica aerogels. J Mater Sci 40(13):3481–3489

    Article  Google Scholar 

  42. Kovacik J (1999) Correlation between Young’s modulus and porosity in porous materials. J Mater Sci Lett 18:1007–1010

    Article  Google Scholar 

Download references

Acknowledgements

This work was supported by Nano-Convergence Foundation (www.nanotech2020.org) funded by the Ministry of Science, ICT and Future Planning (MSIP, Korea) & the Ministry of Trade, Industry and Energy (MOTIE, Korea) (Project Number: R201602310).

Author information

Authors and Affiliations

  1. Department of Materials Science and Engineering, Yonsei University, 50 Yonsei-ro, Seodaemun-gu, Seoul, 03722, South Korea

    Ha-Yoon Nah, Vinayak G. Parale, Hae-Noo-Ree Jung, Kyu-Yeon Lee & Hyung-Ho Park

  2. Korea Institute of Ceramic Engineering and Technology, 101 Soho-ro, Jinju-si, Gyeongsangnam-do, 52851, South Korea

    Chang-Hyun Lim

  3. GLChem Co., Ltd., 143 Yeocheon 3-gil, Ochang-eup, Cheongwon-gu, Cheongju-si, Chungcheongbuk-do, 28127, South Korea

    Yang Seo Ku

Authors
  1. Ha-Yoon Nah
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Vinayak G. Parale
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Hae-Noo-Ree Jung
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Kyu-Yeon Lee
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Chang-Hyun Lim
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Yang Seo Ku
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. Hyung-Ho Park
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Hyung-Ho Park.

Ethics declarations

Conflict of interest

The authors declare that they have no competing interests.

Electronic supplementary material

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Nah, HY., Parale, V.G., Jung, HNR. et al. Role of oxalic acid in structural formation of sodium silicate-based silica aerogel by ambient pressure drying. J Sol-Gel Sci Technol 85, 302–310 (2018). https://doi.org/10.1007/s10971-017-4553-2

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10971-017-4553-2

Keywords

Search

Navigation