Abstract
Regenerated cellulose fibers were successfully wet-spun from a cellulose/NaOH/thiourea/urea aqueous solution by an efficient extrusion dissolution method. The structure changes of these regenerated cellulose fibers that occurred during wet spinning process had been investigated by field-emission scanning electron microscope, carbon nuclear magnetic resonance spectroscopy (13C-NMR), attenuated total reflection infrared spectroscopy and the corresponding two-dimensional spectroscopy, wide-angle-X-ray-diffraction, small-angle-X-ray scattering (SAXS), tensile testing, and thermogravimetric analysis. Results revealed that higher crystallinity and orientation were obtained because of the improved post-processing, while the annealed fiber exhibited lower crystallinity and orientation, owing to a disruption of some oriented crystallites and heat shrinkage during hot air drawing process. SAXS results indicated that the microvoid in the cellulose fibers were smaller with the spinning process, and the pore structure had a more significant impact on the mechanical properties of the regenerated cellulose fibers. Moreover, an increased tensile strength (2.40 cN/dtex) and elongation at break (8.20%) in dry state were obtained in regenerated cellulose fibers due to heat treatment process. Therefore, the structure development contributed toward the improvement of the tensile strength, modulus and thermal stability of the regenerated cellulose fibers during spinning process. On the other hand, a simple, environmentally friendly pathway was proposed for cellulose regeneration, which could significantly affect the cellulose regeneration in current industries.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Altena FW, Smolders CA (1982) Calculation of liquid-liquid phase separation in a ternary system of a polymer in a mixture of a solvent and a nonsolvent. Macromolecules 15:1491–1497. https://doi.org/10.1021/ma00234a008
Avnir D (1989) The Fractal approach to heterogeneous chemistry: surfaces, colloids, polymers. Wiley, New York
Budtova T, Navard P (2016) Cellulose in NaOH–water based solvents: a review. Cellulose 23:5–55. https://doi.org/10.1007/s10570-015-0779-8
Cai J et al (2007) Multifilament fibers based on dissolution of cellulose in NaOH/urea aqueous solution: structure and properties. Adv Mater 19:821–825. https://doi.org/10.1002/adma.200601521
Carrillo F, Colom X, Suñol JJ, Saurina J (2004) Structural FTIR analysis and thermal characterisation of lyocell and viscose-type fibres. Eur Polym J 40:2229–2234. https://doi.org/10.1016/j.eurpolymj.2004.05.003
Chen XM, Burger C, Fang DF, Ruan D, Zhang LN, Hsiao BS, Chu B (2006) X-ray studies of regenerated cellulose fibers wet spun from cotton linter pulp in NaOH/thiourea aqueous solutions. Polymer 47:2839–2848. https://doi.org/10.1016/j.polymer.2006.02.044
Chen MJ, Zhang XQ, Liu CF, Sun RC, Lu FC (2014) Approach to renewable lignocellulosic biomass film directly from bagasse. ACS Sustain Chem Eng 2:1164–1168. https://doi.org/10.1021/sc400555v
Clark DT, Fowler AHK, Stephenson PJ (1983) Application of modern analytical techniques to the investigation of cellulose nitrates. J Macromol Sci Part C 23:217–246. https://doi.org/10.1080/07366578308079443
Crawshaw J, Cameron RE (2000) A small angle X-ray scattering study of pore structure in Tencel (R) cellulose fibres and the effects of physical treatments. Polymer 41:4691–4698. https://doi.org/10.1016/s0032-3861(99)00502-9
Fink HP, Weigel P, Purz HJ, Ganster J (2001) Structure formation of regenerated cellulose materials from NMMO-solutions. Prog Polym Sci 26:1473–1524. https://doi.org/10.1016/s0079-6700(01)00025-9
French AD (2014) Idealized powder diffraction patterns for cellulose polymorphs. Cellulose 21:885–896. https://doi.org/10.1007/s10570-013-0030-4
Fu FY, Yang QL, Zhou JP, Hu HZ, Jia BQ, Zhang LN (2014a) Structure and properties of regenerated cellulose filaments prepared from cellulose carbamate–NaOH/ZnO aqueous solution. ACS Sustain Chem Eng 2:2604–2612. https://doi.org/10.1021/sc500559g
Fu FY, Zhou JP, Zhou XM, Zhang LN, Li DX, Kondo T (2014b) Green method for production of cellulose multifilament from cellulose carbamate on a pilot scale. ACS Sustain Chem Eng 2:2363–2370. https://doi.org/10.1021/sc5003787
Fukuyama K, Kasahara Y, Kasahara N, Oya A, Nishikawa K (2001) Small-angle X-ray scattering study of the pore structure of carbon fibers prepared from a polymer blend of phenolic resin and polystyrene. Carbon 39:287–290. https://doi.org/10.1016/S0008-6223(00)00159-7
Ganster J, Fink HP (2009) 6—the structure of man-made cellulosic fibres. In: Eichhorn S, Hearle JWS, Jaffe M, Kikutani T (eds) Handbook of textile fibre structure, vol 2. Woodhead Publishing, Cambridge, pp 201–233. https://doi.org/10.1533/9781845697310.2.201
Glatter O, Kratky O (1982) Small angle X-ray scattering. Academic Press, London
Guinier A, Fournet G (1955) Small angle scattering of X-rays. Wiley, New York
Guo BQ, Chen WF, Yan LF (2013) Preparation of flexible, highly transparent, cross-linked cellulose thin film with high mechanical strength and low coefficient of thermal expansion. ACS Sustain Chem Eng 1:1474–1479. https://doi.org/10.1021/sc400252e
Håkansson KMO et al (2011) Hydrodynamic alignment and assembly of nanofibrils resulting in strong cellulose filaments. Nat Commun 5:4018. https://doi.org/10.1038/ncomms5018
Hummel M et al (2016) Ionic liquids for the production of man-made cellulosic fibers: opportunities and challenges. In: Rojas OJ (ed) Cellulose chemistry and properties: fibers, nanocelluloses and advanced materials. Springer, Cham, pp 133–168. https://doi.org/10.1007/12_2015_307
Jiang GS et al (2012) Analysis of regenerated cellulose fibers with ionic liquids as a solvent as spinning speed is increased. Cellulose 19:1075–1083. https://doi.org/10.1007/s10570-012-9716-2
Kamide K, Okajima K, Kowsaka K (1992) Dissolution of natural cellulose into aqueous alkali solution: role of super-molecular structure of cellulose. Polym J 24:71–86
Klemm D, Heublein B, Fink HP, Bohn A (2005) Cellulose: fascinating biopolymer and sustainable raw material. Angew Chem Int Ed 44:3358–3393. https://doi.org/10.1002/anie.200460587
Kosan B, Michels C, Meister F (2008) Dissolution and forming of cellulose with ionic liquids. Cellulose 15:59–66. https://doi.org/10.1007/s10570-007-9160-x
Lenz J, Schurz J (1990a) Fibrillar structure and deformation behaviour of regenerated cellulose fibres. Part 2: elementary fibrils and deformation. Cellul Chem Technol 24(6):679–692
Lenz J, Schurz J (1990b) Fractal analysis of cellulosic fibres by small-angle X-ray scattering. Holzforschung 44:227–228
Lenz J, Schurz J, Wrentschur E (1993) Properties and structure of solvent-spun and viscose-type fibres in the swollen state. Colloid Polym Sci 271:460–468
Luo XG, Zhang LN (2013) New solvents and functional materials prepared from cellulose solutions in alkali/urea aqueous system. Food Res Int 52:387–400. https://doi.org/10.1016/j.foodres.2010.05.016
Mahmood H, Moniruzzaman M, Yusup S, Welton T (2017) Ionic liquids assisted processing of renewable resources for the fabrication of biodegradable composite materials. Green Chem 19:2051–2075. https://doi.org/10.1039/c7gc00318h
Mao Y, Zhang LN, Cai J, Zhou JP, Kondo T (2008) Effects of coagulation conditions on properties of multifilament fibers based on dissolution of cellulose in NaOH/urea aqueous solution. Ind Eng Chem Res 47:8676–8683. https://doi.org/10.1021/ie800833w
Moss CE, Butler MF, Müller M, Cameron RE (2002) Microfocus small-angle X-ray scattering investigation of the skin–core microstructure of lyocell cellulose fibers. J Appl Polym Sci 83:2799–2816
Nelson ML, O’Connor RT (1964a) Relation of certain infrared bands to cellulose crystallinity and crystal lattice type. Part II. A new infrared ratio for estimation of crystallinity in celluloses I and II. J Appl Polym Sci 8:1325–1341
Nelson ML, O’Connor RT (1964b) Relation of certain infrared bands to cellulose crystallinity and crystal latticed type. Part I. Spectra of lattice types I, II, III and of amorphous cellulose. J Appl Polym Sci 8:1311–1324
Perez-Madrigal MM, Edo MG, Aleman C (2016) Powering the future: application of cellulose-based materials for supercapacitors. Green Chem 18:5930–5956. https://doi.org/10.1039/C6GC02086K
Porod G (1952) Die Röntgenkleinwinkelstreuung von dichtgepackten kolloiden Systemen. II. Teil. Kolloid Z 125:108–122
Qi HS, Cai J, Zhang LN, Nishiyama Y, Rattaz A (2007) Influence of finishing oil on structure and properties of multi-filament fibers from cellulose dope in NaOH/urea aqueous solution. Cellulose 15:81–89. https://doi.org/10.1007/s10570-007-9142-z
Reddy N, Yang YQ (2015) Innovative biofibers from renewable resources. Springer, Berlin. https://doi.org/10.1007/978-3-662-45136-6_18
Ruan D, Zhang LN, Zhou JP, Jin HM, Chen H (2004) Structure and properties of novel fibers spun from cellulose in NaOH/thiourea aqueous solution. Macromol Biosci 4:1105–1112. https://doi.org/10.1002/mabi.200400120
Ruan D et al (2006) A rapid process for producing cellulose multi-filament fibers from a NaOH/thiourea solvent system. Macromol Rapid Commun 27:1495–1500. https://doi.org/10.1002/marc.200600232
Sahiner N, Demirci S (2017) Natural microgranular cellulose as alternative catalyst to metal nanoparticles for H-2 production from NaBH4 methanolysis. Appl Catal B Environ 202:199–206. https://doi.org/10.1016/j.apcatb.2016.09.028
Segal LC, Creely J, Martin AEJ, Conrad CM (1959) An empirical method for estimating the degree of crystallinity of native cellulose using the X-ray diffractometer. Text Res J 29:786–794
Siró I, Plackett D (2010) Microfibrillated cellulose and new nanocomposite materials: a review. Cellulose 17:459–494. https://doi.org/10.1007/s10570-010-9405-y
Sixta H et al (2015) Ioncell-F: a high-strength regenerated cellulose fibre. Nord Pulp Pap Res J 30:43–57
Swatloski RP, Spear SK, Holbrey John D, Rogers RD (2002) Dissolution of cellose with ionic liquids. J Am Chem Soc 124:4974–4975. https://doi.org/10.1021/ja025790m
Vehviläinen M, Kamppuri T, Grönqvist S, Rissanen M, Maloney T, Honkanen M, Nousiainen P (2015) Dissolution of enzyme-treated cellulose using freezing–thawing method and the properties of fibres regenerated from the solution. Cellulose 22:1653–1674. https://doi.org/10.1007/s10570-015-0632-0
Wanasekara ND, Michud A, Zhu C, Rahatekar S, Sixta H, Eichhorn SJ (2016) Deformation mechanisms in ionic liquid spun cellulose fibers. Polymer 99:222–230. https://doi.org/10.1016/j.polymer.2016.07.007
Wang WC, Li FX, Yu JY, Navard P, Budtova T (2015) Structure and properties of novel cellulose-based fibers spun from aqueous NaOH solvent under various drawing conditions. Cellulose 22:1333–1345. https://doi.org/10.1007/s10570-015-0544-z
Wei W, Meng FB, Cui YH, Jiang M, Zhou ZW (2017) Room temperature dissolution of cellulose in tetra-butylammonium hydroxide aqueous solvent through adjustment of solvent amphiphilicity. Cellulose 24:49–59. https://doi.org/10.1007/s10570-016-1113-9
Yamane C, Mori M, Saito M, Okajima K (1996) Structures and mechanical properties of cellulose filament spun from cellulose/aqueous naoh solution system. Polym J 28:1039–1047. https://doi.org/10.1295/polymj.28.1039
Yang YP, Zhang Y, Dawelbeit A, Yu MH (2016) Dissolving cellulose with twin-screw extruder in a NaOH complex aqueous solution. In: 2016 global conference on polymer and composite materials, PCM 2016, 20 May 2016–23 May 2016, Hangzhou, China. IOP conference series: materials science and engineering. Institute of Physics Publishing, p Ningbo Adhesives and Products Industry Association, Wuhan Advanced Materials Society. https://doi.org/10.1088/1757-899x/137/1/012067
Yang Y, Zhang Y, Dawelbeit A, Deng Y, Lang Y, Yu M (2017) Structure and properties of regenerated cellulose fibers from aqueous NaOH/thiourea/urea solution. Cellulose 24:4123–4137. https://doi.org/10.1007/s10570-017-1418-3
Zhang S, Li FX, Yu JY, Gu LX (2009) Novel fibers prepared from cellulose in NaOH/thiourea/urea aqueous solution. Fibers Polym 10:34–39. https://doi.org/10.1007/s12221-009-0034-8
Zhang S, Li FX, Yu JY, Hsieh YL (2010) Dissolution behaviour and solubility of cellulose in NaOH complex solution. Carbohydr Polym 81:668–674. https://doi.org/10.1016/j.carbpol.2010.03.029
Zhang Y, Li H, Li X, Gibril ME, Yu M (2014) Chemical modification of cellulose by in situ reactive extrusion in ionic liquid. Carbohydr Polym 99:126–131
Zhu CZ, Liu XF, Yu XL, Zhao N, Liu JH, Xu J (2012) A small-angle X-ray scattering study and molecular dynamics simulation of microvoid evolution during the tensile deformation of carbon fibers. Carbon 50:235–243. https://doi.org/10.1016/j.carbon.2011.08.040
Zhu CZ et al (2013) Relationship between performance and microvoids of aramid fibers revealed by two-dimensional small-angle X-ray scattering. J Appl Crystallogr 46:1178–1186. https://doi.org/10.1107/S0021889813010820
Acknowledgments
This work was supported by National Natural Science Foundation of China (51503032 and 21404023), the Fundamental Research Funds for the Central Universities (2232015D-10) and Shanghai Sailing Program (14YF1405200).
Author information
Authors and Affiliations
Corresponding authors
Rights and permissions
About this article
Cite this article
Yang, Y., Zhang, Y., Lang, Y. et al. Structure development in the condensed state of cellulose fiber regenerated from alkali complex solution. Cellulose 25, 1555–1569 (2018). https://doi.org/10.1007/s10570-018-1649-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10570-018-1649-y