Skip to main content
SpringerLink
Log in

Copper, zinc, and nickel recovery from printed circuit boards using an ammonia–ammonium sulphate system

  • ORIGINAL ARTICLE
  • Published:
Journal of Material Cycles and Waste Management Aims and scope Submit manuscript

Abstract

The ammoniacal leaching has been considered very selective for copper compared with other leaching systems; however, there are interactions with zinc and nickel that also form stable ammonia complexes, implying higher consumption of ammonia to obtain high copper recoveries. This research aimed to clarify under which conditions copper, zinc, and nickel can be leached from some components from PCBs and followed the interactions among them. This study focuses on the copper, zinc, and nickel recoveries from connection pins and microchips using ammonia–ammonium sulphate leaching solutions. Factors that influence recovery as the stirring rate, L/S ratio, amount of ammonia and ammonium sulphate, and the type of oxidant were assessed. The results indicated hydrogen peroxide and oxygen are the most efficient oxidants. Metal recoveries of 90% were achieved with excess of oxidant and ammonia, relatively to the estimated stoichiometry. For efficient copper and zinc recoveries, two times the stoichiometric amount of ammonia was needed; four times the stoichiometry was needed for nickel as well as higher ammonium sulphate concentration. Metal recoveries depend strongly on the stability of ammonia complexes, and nickel had lower recovery under almost all conditions tested due to the lower stability of nickel ammonia complexes.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6

Similar content being viewed by others

References

  1. Kaya M (2016) Recovery of metals and nonmetals from electronic waste by physical and chemical recycling processes. Waste Manag 57:64–90

    Article  Google Scholar 

  2. Kumari A, Jha MK, Lee J, Singh RP (2016) Clean process for recovery of metals and recycling of acid from the leach liquor pf PCBs. J Clean Prod 112:4826–4834

    Article  Google Scholar 

  3. Marques AC, Cabrera JM, Malfatti CF (2013) Printed circuit boards: a review on the perspective of sustainability. J Envir Manag 131:298–306

    Article  Google Scholar 

  4. Oishi T, Koyama K, Alam S, Tanaka M, Lee JC (2007) Recovery of high purity copper cathode from printed circuit boards using ammoniacal sulfate or chloride solutions. Hydrometallurgy 89(1–2):82–88

    Article  Google Scholar 

  5. Cui J, Zhang L (2008) Metallurgical recovery of metals from electronic waste: a review. J Hazard Mater 158(2–3):228–256

    Article  Google Scholar 

  6. Birloaga I, Coman V, Kopacek B, Veglió F (2014) An advanced study on the hydrometallurgical processing of waste computer printed circuit boards to extract their valuable content of metals. Waste Manag 34:2581–2586

    Article  Google Scholar 

  7. Oh CJ, Lee SO, Yang HS, Ha TJ, Kim MJ (2003) Selective leaching of valuable metals from waste printed circuit boards. J Air Waste Manag Assoc 53(7):897–902

    Article  Google Scholar 

  8. Silvas FP, Correa MJ, Caldas MP, Moraes VT, Espinosa DC, Tenório JA (2015) Printed circuit board recycling: physical processing and copper extraction by selective leaching. Waste Manag 46:503–510

    Article  Google Scholar 

  9. Choubey PK, Panda R, Jha MK, Lee JC, Pathak D (2015) Recovery of copper and recycling of acid from the leach liquor of discarded printed circuit boards (PCBs). Sep Purif Technol 156:269–275

    Article  Google Scholar 

  10. Janyasuthiwong S, Ugas R, Rene ER, Alessandra C, Esposito G, Lens PNL (2015) Effect of operational parameters on the leaching efficiency and recovery of heavy metals from computer printed circuit boards. J Chem Technol Biotechnol 91:2038–2046

    Article  Google Scholar 

  11. Maguyo MC, Catalino G, Alfafara G, Migo VP, Movillon JL, Rebancos CM (2012) Recovery of copper from spent solid printed circuit board (PCB) wastes of a PCB manufacturing facility by two-step sequential acid extraction and electrochemical deposition. J Environ Sci Manag 15(1):17–27

    Google Scholar 

  12. Yamane LH, Moraes VT, Espinosa DCR, Tenório JAS (2011) Recycling of WEEE: characterization of spent printed circuit boards from mobile phones and computers. Waste Manag 31:2553–2558

    Article  Google Scholar 

  13. Arshadi M, Yaghmaei S, Esmaeili A (2020) Evaluating the optimal digestion method and value distribution of precious metals from different waste printed circuit boards. J Mater Cycles Waste Manag 22:1690–1698

    Article  Google Scholar 

  14. Tunali M, Tunali MM, Yenigun O (2020) Characterization of different types of electronic waste: heavy metal, precious metal and rare earth element content by comparing different digestıon methods. J Mater Cycles Waste Manag. https://doi.org/10.1007/s10163-020-01108-0

    Article  Google Scholar 

  15. Zhang Y, Liu S, Xie H, Zeng X, Li J (2012) Current status on leaching precious metals from waste printed circuit boards. Proc Environ Sci 16:560–568

    Article  Google Scholar 

  16. Birloaga I, Michelis I, Ferella F, Buzatu M, Vegliò F (2013) Study on the influence of various factors in the hydrometallurgical processing of waste printed circuit boards for copper and gold recovery. Waste Manag 33(4):935–941

    Article  Google Scholar 

  17. Li J, Xu X, Liu W (2012) Thiourea leaching gold and silver from the printed circuit boards of waste mobile phones. Waste Manag 32:1209

    Article  Google Scholar 

  18. Dorin R, Woods R (1991) Determination of leaching rates of precious metals by electrochemical techniques. J Appl Electrochem 21(5):419–424

    Article  Google Scholar 

  19. Montero R, Guevara A, De la Torre E (2012) Recovery of gold, silver, copper and niobium from printed circuit boards using leaching column technique. J Earth Sci Eng 2:590–595

    Google Scholar 

  20. Oraby EA, Li H, Eksteen JJ (2019) An alkaline glycine-based leach process of base and precious metals from powdered waste printed circuit boards. Waste Biomass Valor. https://doi.org/10.1007/s12649-019-00780-0

    Article  Google Scholar 

  21. Ficeriová J, Balaz P, Gock E (2011) Leaching of gold, silver and accompanying metals from circuit boards (PCBs) waste. Acta Montanistica Slovaca 6(2):128–131

    Google Scholar 

  22. Ha V, Lee JC, Jeong J, Ha H, Jha MK (2010) Thiosulfate leaching of gold from waste mobile phones. J Hazard Mater 178(1):1115–1119

    Article  Google Scholar 

  23. Liu R, Shieh R, Ruth S, Yeh YL, Lin CH (2009) The general utilization of scrapped PC board. Waste Manag 29(11):2842–2845

    Article  Google Scholar 

  24. XiaoY YY, van den Berg SJ, Agterhuis H, Visser G, Bol D (2013) Hydrometallurgical recovery of copper from complex mixtures of end-of-life shredded ICT products. Hydrometallurgy 140:128–134

    Article  Google Scholar 

  25. Sun ZHI, Xiao Y, Sietsma J, Agterhuis H, Yang Y (2016) Complex electronic waste treatment—an effective process to selectively recover copper with solutions containing different ammonium salts. Waste Manag 57:140–148

    Article  Google Scholar 

  26. Koyama K, Tanaka M, Lee J (2006) Copper leaching behavior from waste printed circuit board in ammoniacal alkaline solution. Mater Trans 47(7):1788–1792

    Article  Google Scholar 

  27. Liu JC, Kao TH (2003) Extraction of Cu and Pb from printed circuit board sludge using ammonia solutions. Water Sci Technol 47(1):167–172

    Article  Google Scholar 

  28. Yang J-G, Wu Y-T, Li J (2012) Recovery of ultrafine copper particles from metal components of waste printed circuit boards. Hydrometallurgy 121–124:1–6

    Article  Google Scholar 

  29. Duan H, Wang Z, Yuan X, Wang S, Guo H, Yang X (2017) A novel sandwich supported liquid membrane system for simultaneous separation of copper, nickel and cobalt in ammoniacal solution. Sep Purif Technol 173:323–329

    Article  Google Scholar 

  30. Rudnik E, Pierzynka M, Handzlik P (2016) Ammoniacal leaching and recovery of copper from alloyed low-grade e-waste. J Mater Cycles Waste Manag 18:318–328

    Article  Google Scholar 

  31. Luo R (1987) Overall equilibrium diagrams for hydrometallurgical systems: copper–ammonia–water system. Hydrometallurgy 17:177–199

    Article  Google Scholar 

  32. Navarro P, Vargas C, Villarroel A, Alguacil FJ (2002) On the use of ammoniacal/ammonium thiosulphate for gold extraction from a concentrate. Hydrometallurgy 65:37–42

    Article  Google Scholar 

  33. Sun ZH, Xiao Y, Sietsma J, Agterhuis H, Visser G, Yang Y (2015) Selective copper recovery from complex mixtures of end-of-life electronic products with ammonia-based solution. Hidrometallurgy 152:91–99

    Article  Google Scholar 

  34. Meng X, Han KN (1996) The principles and applications of ammonia leaching of metals—a review. Miner Process Extr Metall Rev 16(1):23–61

    Article  Google Scholar 

  35. Sawyer Clair N (1994) Chemistry for environmental engineering, 4th edn. McGraw-Hill, New York

    Google Scholar 

  36. Ying LJ, Neng SG (2008) The Research of copper leaching from the waste computer mainboards. IEEE, Piscataway

    Google Scholar 

Download references

Acknowledgements

This work was financially supported by: project UID/EQU/00511/2019—Laboratory for Process Engineering, Environment, Biotechnology and Energy—LEPABE funded by national funds through FCT/MCTES (PIDDAC); Project “LEPABE-2-ECO-INNOVATION”—NORTE‐01‐0145‐FEDER‐000005, funded by Norte Portugal Regional Operational Programme (NORTE 2020), under PORTUGAL 2020 Partnership Agreement, through the European Regional Development Fund (ERDF).

Author information

Authors and Affiliations

  1. LEPABE, Department of Metallurgical and Materials Engineering, Faculty of Engineering, University of Porto , Dr. Roberto Frias, 4200-465, Porto, Portugal

    Sílvia C. Pinho, Cristiana Ribeiro & Manuel F. Almeida

  2. LEPABE, Department of Chemical Engineering, Faculty of Engineering, University of Porto, Dr. Roberto Frias, Porto, 4200-465, Portugal

    Cristiana Ribeiro & Conceição A. Ferraz

Authors
  1. Sílvia C. Pinho
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Cristiana Ribeiro
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Conceição A. Ferraz
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Manuel F. Almeida
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Sílvia C. Pinho.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Pinho, S.C., Ribeiro, C., Ferraz, C.A. et al. Copper, zinc, and nickel recovery from printed circuit boards using an ammonia–ammonium sulphate system. J Mater Cycles Waste Manag 23, 1456–1465 (2021). https://doi.org/10.1007/s10163-021-01226-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10163-021-01226-3

Keywords

Search

Navigation