Abstract
The present study investigates a large power thermal bubble micro-ejector with induction heating device. The traditional thermal-bubble ejectors adopted resistors as the heating resources, it can only work with lower power and convey liquid with lower flow rate. Induction heating devices are adopted to replace the resistor for heating liquid in this paper. With this heating method, there is no physical contact between the heating core and the external power supply circuit. The liquid in the chamber of micro-ejector is heated by the induction heating device and changes from liquid phase to gas phase, generating vapor bubbles in the micro chamber of the micro ejector. The bubble expands rapidly and ejects droplets through the nozzle. The prototype of the micro-ejector is fabricated and experiments are carried out. Continuous droplets are ejected out from the nozzle as the applied AC current is 0.6–0.65 A with the power frequency of 100 kHz. The total volume of the continuous droplets is ranging from 18.84 to 49.87 nL, and the corresponding flow rate is about 0.52–1.36 μL/min. Furthermore, this new micro-ejector can be adopted in conveying of micro-scale liquid, the injection of trace drugs and the 3D printing.
Similar content being viewed by others
References
Allen RR, Meyer JD, Knight WR (1985) Thermodynamics and hydrodynamics of thermal ink jets. Hewlett Packard J 36:26–27
Baek SS, Lim H-T, Song H, Kim Y-S, Bae K-D, Cho C-H, Lee C-S, Shin J-W, Shin S-J, Kuk K, Oh Y-S (2004) A novel back-shooting inkjet printhead using trench-filling and SOI wafer. Sens Actuators A 114:392–397
Cabal A, Ross DS, Lebens JA, Trauernicht DP (2005) Thermal actuator with optimized heater for liquid drop ejectors. Sens Actuators A 123–124:531–539
Deng P, Lee Y.-K., Cheng P. (2004) Micro bubble dynamics in DNA solution. J Micromech Microeng 14:693–701
Deng P, Lee Y.-K., Cheng P. (2005) Measurements of micro bubble nucleation temperatures in DNA solutions. J Micromech Microeng 15:564–574
Jun T, Kim CJ (1996) Microscale pumping with traversing bubbles in microchannels. In: Proceeding of IEEE solid-state sensor actuator workshop. Hilton Head Island, pp 144–147
Lee J-D, Yoon J-B, Kim JK, Chung H-J, Lee C-S, Lee H-O, Lee H-J, Kim C-K, Han C-H (1999) A thermal ink-jet printhead with a monolithically fabricated nozzle plate self-aligned ink feed hole. J Microelectromech Syst 8:229–236
Rudnev V, Loveless D, Cook R (1998) Handbook of induction heating. Marcel Dekker Inc., New York, pp 527–532
Sen AK, Darabi J (2007) Droplet ejection performance of a monolithic thermal inkjet print head. J Micromech Microeng 17:1420–1427
Stachowiaka JC, von Muhlenb MG, Lia TH, Jalilianb L, Parekh SH, Fletcher DA (2007) Piezoelectric control of needle-free transdermal drug delivery. J Control Release 124:88–97
van den Broek DM, Elwenspoek M (2008) Explosive micro-bubble actuator. Sens Actuators A 145–146:387–393
Wang D-A, Cheng C-H, Hsieh Y-H, Zhang Z-X (2007) Analysis of an annular PZT actuator for a droplet ejector. Sens Actuators A 137:330–337
Zhou H, Gué AM (2010) Simulation model and droplet ejection performance of a thermal-bubble microejector. Sens Actuators B 145:311–319
Acknowledgments
This work is done with some help of Beijing key laboratory of Advanced Manufacturing Technology. The authors would like to thank Prof. Zhaomiao Liu and Dr. Longxiang Zhang for help in experiment. Project of the National Natural Science Foundation of China No. 51105011 supported this research. This work was supported by the Specialized Research Fund for the Doctoral Program of Higher Education (No. 20101103120002). Project of Beijing Board of education No. KM201210005015 supported this research.
Author information
Authors and Affiliations
Corresponding author
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
About this article
Cite this article
Hou, Y., Liu, B. & Yang, J. Research on a large power thermal bubble micro-ejector with induction heating. Microsyst Technol 22, 103–108 (2016). https://doi.org/10.1007/s00542-014-2367-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00542-014-2367-5