Abstract
The optimal combination of different types of gravity observations is the key to obtaining a high-resolution and high-precision regional gravity model. Current studies based on spherical radial basis functions (SRBFs) majorly consider a single-level approach for data combination. Despite the promising results reported in numerous publications, it has been suspected that the single-level model might be biased towards high-resolution measurements. Instead, a multi-resolution representation (MRR) can be applied to further take into consideration the varying spectral sensitivities of different observation techniques. In this study, we develop a new MRR scheme based on the pyramid algorithm and sequential parameter estimation. We propose strategies to solve the challenges in the practical application of the pyramid algorithm, and this study represents its first successful realization in regional gravity field modeling. The modeling results based on both simulated and real gravity data show that either the single-level approach or the MRR without pyramid algorithm is able to capture gravity information from lower resolution measurements as sufficient as our newly developed MRR algorithm. In the simulated case, the RMS error w.r.t. the validation data obtained by the MRR based on the pyramid algorithm decreases by 50% and 35%, in comparison to that of the single-level model and the MRR without pyramid algorithm, respectively. In the real case, the improvement achieved by the MRR based on the pyramid algorithm is 35% and 23% in the onshore area, and it reaches 63% and 57% in the offshore area, compared to the single-level approach and the MRR without pyramid algorithm, respectively.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Regional gravity field modeling is an important topic in geodesy; it plays an essential role for applications in geophysics and physical height system realization. A high-resolution and high-precision geoid model derived from regional gravity field modeling is the key to the realization of the International Height Reference System (IHRS, Sánchez et al. 2021). In the last decades, spherical radial basis functions (SRBFs, see e.g., Freeden et al. 1998; Freeden and Michel 2004; Schmidt et al. 2007) have been widely used for regional gravity field modeling. Thanks to their localizing features in both the spectral and the spatial domain, SRBFs are an appropriate approach to consider the heterogeneity of different gravity data types with varying spectral and spatial resolutions.
In regional gravity field modeling, local high-resolution gravity measurements (e.g., terrestrial, airborne, and shipborne gravity data) are usually combined with medium-resolution data (e.g., inferred from satellite altimetry missions) and low-resolution global data provided by dedicated satellite gravity missions, such as the Gravity Recovery and Climate Experiment (GRACE, Tapley et al. 2004) and the Gravity Field and Steady-State Ocean Circulation Explorer (GOCE, Rummel et al. 2002). Each observation technique has different spectral sensitivities and varying data distribution. Thus, a data combination method that extracts the maximum gravity information from different measurements is required to ensure the best possible high-precision regional gravity model. Typically, the data combination based on SRBFs is implemented using a single-level approach (see, e.g., Bentel et al. 2013a, b; Lieb et al. 2016; Bucha et al. 2016; Wu et al. 2017a, b; Liu et al. 2020a, b). In this approach, different observation techniques are combined at the maximum degree of expansion, and their contributions to the final gravity model are determined by the relative weighting between each data set. This approach is straightforward, and promising modeling results have been reported in the aforementioned publications. However, the contribution of measurements with medium to low resolution (e.g., altimetry data, satellite gravity data) could be understated, since they are not sensitive at high spectral degrees. For instance, Klees et al. (2018) demonstrate that the single-scale model lacks the flexibility to deal with data sets of significantly different bandwidths, while Wu et al. (2018) state that the single-level approach may fail to extract the full information contained in the gravity data.
To take the spectral sensitivity of different observation techniques into consideration and to combine heterogeneous data by spectral weights, a spectral combination can be applied (see, e.g., Sjöberg 1981; Kern et al. 2003; Denker 2013). The spectral combination based on SRBFs can be realized through a multi-resolution representation (MRR). The MRR of the gravity field was initially proposed by Freeden et al. (1998), Freeden (1999), and Haagmans et al. (2002), and its realization has been investigated in the last two decades. The MRR is often associated with wavelet functions. Kusche et al. (1998) conclude that the spherical wavelet functions show outstanding properties in the medium frequency band, and they are thus recommended for modeling the medium wavelength part of the gravity field. Beylkin and Cramer (2002) present several multi-resolution gravity models and show their performance results. Fengler et al. (2007) set up an MRR approach based on GRACE data using the cubic polynomial (CuP) wavelets and show that they are an appropriate tool to investigate regional and temporal variations of the Earth’s gravity field. Panet et al. (2011) introduce the iterative domain decomposition by extending the Poisson wavelet modeling approach (Holschneider et al. 2003) to combine the surface (land, marine and altimetry) gravity data with satellite gravity data. Bolkas et al. (2016) state that wavelet decomposition is a useful tool for fusing terrestrial gravity data with satellite and airborne data and show that the multiscale fused model is able to fill data gaps.
Schmidt et al. (2005, 2006, 2007) develop an MRR approach where the representation is decomposed into an expansion in terms of spherical harmonics for the long-wavelength part, and a number of frequency-dependent detail signals in terms of wavelets for the medium and high frequency parts. This MRR was applied for regional gravity field modeling by Lieb (2017) and Wu et al. (2018), where the coefficients for calculating the detail signals are estimated simultaneously at each resolution level, using all or selected data groups. However, if all observation types are used at each level, the corresponding detail signals are strongly correlated (Lieb 2017). If only specific data sets are used, large data gaps may occur, and the prior information is insufficient for filling these data gaps at higher resolution levels. This leads to large erroneous effects in the output signals. Consequently, Lieb (2017) recommends for future work the implementation of the pyramid algorithm (Freeden et al. 1998) to consider all available information by connecting the different levels. Klees et al. (2018) show that a two-scale (or multi-scale) model needs to be applied in combination with a sequential estimation of the scale-dependent coefficients. The sequential estimation can be realized by applying the pyramid algorithm, which determines the coefficients of the lower resolution levels sequentially from the coefficients of the higher level, by successive low-pass filtering.
Although the pyramid algorithm was proposed nearly two decades ago, its practical application based on parameter estimation has never been realized in regional gravity field modeling, until this study. This is due to the challenges of applying the pyramid algorithm in the regional case, as stated by Lieb (2017): (1) it is difficult to set up a proper low-pass filter matrix in the regional case, and (2) the margin size has to be adapted appropriately at each level to minimize edge effects. We come up with methods in this study to solve these difficulties: (1) a low-pass filter is newly introduced in case of using the Reuter grid; (2) the choice of the margin size and the setting up of the estimation model at each resolution level are characterized; (3) strategies for reducing edge effects in the calculated detail signals are proposed.
A new MRR scheme based on the pyramid algorithm is developed, as visualized in Fig. 1, the text in blue highlights the novelty of this work. One main innovation is the realization of the sequential parameter estimation in the MRR scheme. The coefficients are firstly estimated at the highest chosen resolution level I using only the high-resolution data set(s) 1, and they are used to compute the detail signal \(\varvec{G}_I\) by wavelet functions. Then, these estimated coefficients are transformed to the next lower level \(I-1\) by applying a low-pass filtering, i.e., the pyramid algorithm using the proposed low-pass filter matrix \(\varvec{L}_{I-1}\). At the lower level \(I-1\), the coefficient vector is updated by the lower-resolution data set(s) 2 introduced at this level. This updated coefficient vector is then used in combination with wavelet functions to calculate the detail signal \(\varvec{G}_{I-1}\). Continuing this process until the lowest level \(i'\) of the MRR, all data sets are introduced into the scheme at different resolution levels and the coefficient vectors as well as the detail signals are obtained. At each lower resolution level, the coefficients from the pyramid algorithm are combined directly with the new data set(s), through the parameter estimation procedure. In the two-scale model presented by Klees et al. (2018), the coefficients from the high-resolution level are used to generate a new pseudo data set (with the same resolution as the low-resolution data set), which is then combined with the low-resolution data set to estimate the coefficients of the lower level. However, the authors point out that the high-resolution data set is required to have a larger area coverage than the low-resolution data set (due to edge effects), which frequently cannot be fulfilled when dealing with real data. In this study, we solve this limitation by the direct combination of the coefficient vector and the new data set(s), in analogy to a Kalman filter.
In this research, we additionally demonstrate that: (1) different observation types can be introduced into the evaluation model at the spectral level of their highest sensitivities, which makes it possible to benefit from the individual strengths of each data set optimally; (2) since all computations within the pyramid algorithm are based on linear equation systems (Schmidt et al. 2015), all covariance information can easily be calculated following the law of error propagation from the higher levels and serve as input for the lower levels; (3) as the number of required SRBFs decreases from the highest level to the lower levels, the design matrices of the lower-resolution data sets are now calculated with a smaller number of grid points, which reduces the computational effort significantly. We test the MRR based on the pyramid algorithm by using simulated data and then apply it to real data in different study areas. The modeling results are directly compared to those obtained from the single-level approach and the MRR without using the pyramid algorithm (where the coefficients are estimated independently at each level using all types of observations) in order to highlight the benefits of the MRR based on the pyramid algorithm.
This work is organized as follows: In Sect. 2, we introduce the fundamental concepts of the MRR based on SRBFs, the wavelet functions, and the pyramid algorithm. Section 3 explains the newly developed MRR procedure based on the sequential parameter estimation, and shows how the coefficient vector from the pyramid algorithm is updated by including new observations at the lower levels. Sections 4 and 5 present the performance of our approach based on simulated and real data, respectively. The model configuration is explained, and the developed strategy for reducing edge effects is demonstrated. The results are evaluated and discussed, and comparisons are made with both the single-level approach and the MRR without pyramid algorithm. Finally, Sect. 6 provides conclusions and outlook.
2 Multi-resolution representation
2.1 Spherical radial basis functions
In general, SRBFs are isotropic localizing functions centered at grid points \(P_k\) on a sphere \({\Omega _{R}}\) with radius R (Freeden et al. 1998; Schmidt et al. 2007), and can be defined by the Legendre series
wherein \(\varvec{x}=r\cdot \varvec{r}\) is the position vector of an arbitrary point \(P(\varphi ,\lambda ,r)\), with latitude \(\varphi \), longitude \(\lambda \), and radial distance \(r=|\varvec{x}|=R+h'\); \(h'\) is the height of P over the sphere \({\Omega _{R}}\); \(\varvec{r}=[\cos \varphi \cos \lambda ,\cos \varphi \sin \lambda ,\sin \varphi ]^T\) is the corresponding unit vector. \(\varvec{x}_k=R\cdot \varvec{r}_k\) is the position vector of a grid point \(P_k\). \(P_n\) is the Legendre polynomial of degree n, which is a function of the spherical distance between the point P and the grid point \(P_k\). \(n_{\max }\) is the maximum degree of the expansion. \(B_n\) is the Legendre coefficients, which specify the shape of the SRBFs. In case of \(B_n=1\) for all degree values \(n=0, 1, \ldots , n_{\max }\), the SRBF is defined as the reproducing kernel \(K_{\text {rep}}(\varvec{x},\varvec{x}_k)\), which has the ability of the unique reproduction of a harmonic function. To be more specific, the convolution of a harmonic function \(F(\varvec{x})\) (band-limited with \(n=0, 1, \ldots , n'\le n_{\max }\)) with the reproducing kernel \(K_{\text {rep}}\) is equal to the original function (Schmidt et al. 2007), i.e.,
Any gravity observation \(y(\varvec{x})\) can be represented as a series expansion in terms of the SRBFs, i.e.,
where K and \(d_k\) are the number of grid points and the corresponding series coefficients, respectively. \(s(\varvec{x})\) is the truncation error, and \(e(\varvec{x})\) is the observation error. It is worth mentioning that the general expression (1) of the basis functions \(B(\varvec{x},\varvec{x}_k)\) needs to be adapted for describing different gravitational functionals (e.g., the gravity disturbance \(\delta g\) or the gravity anomaly \(\Delta g\)). A list of basis functions adapted to different functionals can be found in Koop (1993) and Liu et al. (2020a).
2.2 Multi-resolution representation
The fundamental idea of the MRR is to split a given input signal into a smoothed version and a number of detail signals by successive low-pass filtering (Schmidt et al. 2007). Following Schmidt et al. (2006), the MRR of the gravity functional \(F(\varvec{x})\) can be expressed as
where \(\bar{F}(\varvec{x})\) is a reference model, i.e., usually the long-wavelength component from a global gravity model (GGM), and it is used as the background model within the remove-compute-restore (RCR, e.g., Forsberg 1993) procedure. \(G_i(\varvec{x})\) is the detail signal of resolution level i, and \(s(\varvec{x})\) is the truncation error.
To set up the resolution level i, the frequency domain needs to be discretized. Each resolution level defines a frequency band, and thus, includes a certain number of degree values. In this study, the upper boundary (maximum degree value) \(n_i\) of each level is defined as
It is worth mentioning that the resolution levels can also be adapted differently, i.e., the base 2 in Eq. (5), which specifies the range of the frequency bands, can be chosen as a different number (see Schmidt et al. 2007 for more details). Figure 2 (cf. Lieb et al. 2016) visualizes the discretization of the frequency domain, and the relation between the resolution level i and its corresponding spectral degree \(n_i\) as well as spatial resolution \(\rho _i\). The corresponding maximum spatial resolution of level i is \(\rho _i=\pi R/n_i\), with R the Earth’s radius. Gravity data obtained from different observation techniques can then be classified according to their spectral resolution. Terrestrial, airborne, and shipborne observations are high-resolution regional data, thus, they cannot be used to estimate the low-frequency part. Therefore, they should be combined with the medium-resolution satellite altimetry measurements, and the low-resolution satellite gravimetry data, such as GRACE and GOCE.
2.3 Wavelet functions
SRBFs (1) can act as high-pass, low-pass or band-pass filters, depending on the chosen Legendre coefficients \(B_n\), and a harmonic function \(F(\varvec{x})\) can be filtered by it through a spherical convolution (Schmidt et al. 2007; Liu et al. 2020b). In case of using a band-limited SRBF, e.g., a spherical scaling function \(B(\varvec{x},\varvec{x}_k)=:\Phi _i(\varvec{x},\varvec{x}_{k,i})\), which means the Legendre coefficient \(B_n=:\phi _{n,i}>0\) for degree \(n=0, 1, \ldots , n_{\max }=:2^i-1\) and \(\phi _{n,i}=0\) for degree \(n>2^i-1\), the SRBF acts as a low-pass filter. Based on the scaling function, a spherical wavelet function \(\Psi _i(\varvec{x},\varvec{x}_{k,i})\), which can be interpreted as a band-pass filter, is defined as
where \(\varvec{x}_{k,i}\) is the position vector of the grid point \(P_{k,i}\) at resolution level i, and the Legendre coefficients \(\psi _{n,i}\) are computed as
The detail signal \(G_i(\varvec{x})\) of level i in Eq. (4) can then be defined in terms of the spherical wavelet function as
where \(K_i\) and \(d_{k,i}\) are the number of grid points and the corresponding series coefficients, respectively, at the level i. As explained in Liu et al. (2020b), the coefficients \(d_{k,i}\) do not depend on the choice of the SRBFs, as soon as the SRBFs are band-limited up to the same degree, i.e., their Legendre coefficients are equal to 0 for all degree values \(n>2^i-1\). Thus, the same set of unknown coefficients \(d_{k,i}\) at level i can be used with both the spherical scaling function and the spherical wavelet function of the same level. Also, it is possible to use different types of SRBFs in the analysis step (in which the unknown coefficients are estimated) and in the synthesis step (in which the estimated coefficients are used to calculate the output gravity models), respectively.
In this study, we use the following spherical scaling functions (see Schmidt et al. 2007; Lieb et al. 2016):
-
1.
The Shannon function, which could be interpreted as the reproducing kernel (see Sect. 2.1), its Legendre coefficients are given by
$$\begin{aligned} \phi _{n,i}^{Sha}= \left\{ \begin{array}{ll} 1 &{}\quad \text {for}\; n\; \in \ [0, 2^i-1]\\ 0 &{}\quad \text {else} \end{array}\right. . \end{aligned}$$(9) -
2.
The Blackman function, its Legendre coefficients are given by
$$\begin{aligned} \phi _{n,i}^{Bla}=\left\{ \begin{array}{ll} 1 &{}\quad {\text {for}}\; n\; \in [0,2^{i-1}-1]\\ (A(n))^2 &{} \quad {\text {for}}\; n\; \in [2^{i-1},2^i-1]\\ 0 &{}\quad {\text {else}} \end{array}\right. , \end{aligned}$$(10)where
$$\begin{aligned} A(n)=\frac{21}{50}-\frac{1}{2}\text {cos}\left( \frac{2\pi n}{2^i}\right) +\frac{2}{25}\text {cos}\left( \frac{4\pi n}{2^i}\right) . \end{aligned}$$(11)
The Shannon scaling function is used in the analysis step to estimate the unknown coefficients, and the Blackman wavelet function (with Legendre coefficients \(\psi _{n,i}^{Bla}=\phi _{n,i}^{Bla}-\phi _{n,i-1}^{Bla})\) is applied in the synthesis step to calculate the detail signals at each level. The reason for using the Shannon function in the analysis step is to avoid the loss of spectral information. An SRBF with smoothing features, such as the Blackman function, is used in the synthesis step to reduce erroneous effects (Lieb et al. 2016; Liu et al. 2020b). Figure 3 visualizes the characteristics of the Blackman wavelet function in the spatial (upper plot) and the spectral domain (bottom plot) for different resolution levels. As we can see, the Blackman wavelet function has smoothing features. At the same time, it has strict band-pass features, i.e., only the Legendre coefficients within the spectral band \([2^{i-2},2^i)\) are not zero. The spectral weight, which is defined by the Legendre coefficients, increases from degree \(2^{i-2}\) to \(2^{i-1}\) and decreases from degree \(2^{i-1}\) to \(2^i\). In the spectral domain, the corresponding frequency band becomes wider at higher resolution levels. In the spatial domain, with increasing resolution level i, the peak becomes sharper.
2.4 The pyramid algorithm
Freeden (1999) shows that the coefficients of neighboring resolution levels depend on each other linearly, and thus, can be computed successively. Therefore, the pyramid algorithm can be set up to determine the coefficients of the lower resolution levels from the coefficients of the higher level by a low-pass filtering. This procedure is based on a down sampling strategy, as the number of coefficients decreases at each level. With the pyramid algorithm, the coefficients at level i \((i=i', i'+1, \ldots , I-2, I-1)\) can be expressed as
where \(\varvec{L}_i\) is a \(K_i\times K_{i+1}\) low-pass filter matrix, transforming the \(K_{i+1}\times 1\) coefficient vector \(\varvec{d}_{i+1}\) of the higher level \(i+1\) to the \(K_i\times 1\) coefficient vector \(\varvec{d}_{i\mid i+1}\) of the lower level i. \(\varvec{\Sigma }_{d_{i\mid i+1}}\) is the covariance matrix of \(\varvec{d}_{i\mid i+1}\) obtained from the covariance matrix \(\varvec{\Sigma }_{d_{i+1}}\) following the law of error propagation.
According to Schmidt et al. (2007), the low-pass filter matrix \(\varvec{L}_i\) can be decomposed as
where \(\varvec{H}_i\) is a \(K_i\times K_{i+1}\) matrix containing the reproducing kernel \({K_\mathrm{{rep}}}(\varvec{x}_{k,i},\varvec{x}_{k,i+1})\) between the grid points \(P_{k,i+1}\) (\(k=1, 2,\ldots , K_{i+1}\)) of level \(i+1\) and the grid points \(P_{k,i}\) (\(k=1, 2,\ldots , K_i\)) of level i. \(\varvec{W}_i\) is the \(K_i\times K_i\) diagonal matrix of the integration weights associated with the grid points \(P_{k,i}\) of level i, and it depends on the implemented type of grid. Although the Reuter grid (Reuter 1982) is one of the most commonly used grids in regional gravity field modeling, there are no previous studies about how to define \(\varvec{W}_i\) for this type of grid. In this study, we develop a strategy to set up the corresponding integration weights, which read
where \(Z_i\) is the total number of the Reuter grid points on the sphere at level i. Reuter grids are regarded as equidistributed point systems on the sphere (Fengler et al. 2004; Eicker 2008), and the corresponding integration weights are constant for each grid point.
3 Parameter estimation
In this paper, a new MRR scheme is developed based on the pyramid algorithm using sequential parameter estimation. The initial step of the MRR procedure is to estimate the unknown coefficient vector \(\varvec{d}_I=[d_{1,I},\ d_{2,I},\ldots ,\ d_{K_I,I}]^T\) at the highest resolution level I using parameter estimation (Koch 1999; Schmidt et al. 2007). Assuming that P groups of observations are used at level I, the estimated coefficient vector \(\widehat{\varvec{d}}_I\) and the corresponding covariance matrix \(D(\widehat{\varvec{d}}_I)=\widehat{\varvec{\Sigma }}_{d_I}\) can be obtained as (Liu et al. 2020a, b)
\(\varvec{y}_{p,I}\) is the observation vector of the \(p^{th}\) gravity data set used at level I, \(\varvec{P}_{p,I}\) is its positive definite weight matrix, and \(\varvec{A}_{p,I}\) is the design matrix, which contains the corresponding (adapted) scaling functions. \(\varvec{\mu }\) is the expectation vector of the coefficient vector \(\varvec{d}_I\), and \(\varvec{P}_\mu \) is its given positive definite weight matrix. \(\sigma _{p,I}^2\) and \(\sigma _\mu ^2\) are the corresponding variance factors for the observations \(\varvec{y}_{p,I}\) and the prior information \(\varvec{\mu }\), respectively.
After estimating the scaling coefficient vector and its covariance matrix, they are used to calculate the scaling coefficient vector \(\varvec{d}_{I-1\mid I}\) and the corresponding covariance matrix \(\varvec{\Sigma }_{d_{I-1\mid I}}\) of the next lower level, by applying the pyramid algorithm according to Eqs. (12) and (13). Then, instead of transforming the coefficient vector \(\varvec{d}_{I-1\mid I}\) directly to the next lower level \(I-2\), which is the usual procedure in previous studies about the pyramid algorithm, it is updated by the gravity observations introduced at this level \(I-1\). The updated coefficient vector \(\varvec{d}_{I-1}\) is then transformed to the level \(I-2\) following Eqs. (12) and (13). Assuming that Q groups of observations \(\varvec{y}_{q,I-1}\) are introduced at level \(I-1\), the combination of \(\varvec{y}_{q,I-1}\) and \(\varvec{d}_{I-1\mid I}\) is realized through the parameter estimation:
The updated coefficient vector of level \(I-1\) is estimated as
with the covariance matrix
The variance factors \(\sigma _{1,I-1}^2, \sigma _{2,I-1}^2, \ldots , \sigma _{Q,I-1}^2\) of the data sets \(\varvec{y}_{1,I-1}, \varvec{y}_{2,I-1}, \ldots , \varvec{y}_{Q,I-1}\) are estimated by the variance component estimation (VCE, Koch and Kusche 2002).
The combination of \(\varvec{y}_{I-1}=[\varvec{y}_{1,I-1}^T, \ \varvec{y}_{2,I-1}^T, \ldots , \varvec{y}_{Q,I-1}^T]^T\) and \(\varvec{d}_{I-1|I}\) can also be solved in analogy to the Kalman filter (Kalman 1960), where \(\varvec{d}_{I-1|I}\) and \(\varvec{\Sigma }_{d_{I-1|I}}\) can be regarded as the predicted state vector and the related predicted covariance matrix, respectively. Then the corrected state vector \(\varvec{d}_{I-1}\) as well as its covariance matrix \(\varvec{\Sigma }_{d_{I-1}}\) are computed by incorporating the involved measurements \(\varvec{y}_{I-1}\) at level \(I-1\)
where \(\varvec{K}_{I-1}\) is the gain matrix
with \(\varvec{A}_{I-1}=[\varvec{A}_{1,I-1}^T, \ \varvec{A}_{2,I-1}^T, \ldots , \ \varvec{A}_{Q,I-1}^T]^T\), and \(\varvec{\Sigma }_{y_{I-1}}\) being the covariance matrix of the observation vector \(\varvec{y}_{I-1}\). After taking into account the matrix identities, the solution delivered by Eqs. (21) and (22) ends up identical to Eqs. (19) and (20). We refer to Koch (1999) and Erdogan et al. (2020) for the details of the matrix identities.
In the synthesis step, the estimated coefficient vector \(\widehat{\varvec{d}}_{I-1}\) and its covariance matrix \(\widehat{\varvec{\Sigma }}_{d_{I-1}}\) are used to calculate the estimated detail signal \(\widehat{\varvec{G}}_{I-1}\) as well as its covariance matrix \(\widehat{\varvec{\Sigma }}_{G_{I-1}}\)
where \(\widehat{\varvec{G}}_{I-1}=[\widehat{G}_{I-1}(\varvec{x}_1), \widehat{G}_{I-1}(\varvec{x}_2), \ldots , \widehat{G}_{I-1}(\varvec{x}_C)]^T\) is the vector of the estimated detail signal values at the computation points \(\varvec{x}_1, \varvec{x}_2, \ldots , \varvec{x}_C\) of the output gravity model. \(\varvec{B}_{I-1}\) is the design matrix, which contains the Blackman wavelet functions \(\Psi _{I-1}(\varvec{x}_c,\varvec{x}_{k,I-1})\), as defined in Eq. (6), between the computation points of the gravity model and the grid points of level \(I-1\).
The developed MRR procedure is summarized in Fig. 4: after determining the estimated coefficient vector \(\widehat{\varvec{d}}_I\) at the highest level I, it can be used to compute the detail signal \(\widehat{\varvec{G}}_I\) and to start the pyramid algorithm, i.e., to calculate the coefficient vector \(\varvec{d}_{I-1\mid I}\) of the next lower level. Then, this coefficient vector \(\varvec{d}_{I-1\mid I}\) is updated by introducing the observations at level \(I-1\). Continuing this process until the lowest level of the MRR, the scaling coefficients and the detail signals of each level can be obtained, and thus, the final gravity functional is obtained according to Eq. (4). In this process, the input gravity data obtained from different observation techniques can be introduced into the estimation model at the resolution level of their highest sensitivities. Hence, they are able to contribute to the final model with maximum gravity information. Typically, the terrestrial data are used at the highest level. Then the shipborne or airborne data can be introduced at a level lower, followed by the altimetry data and the satellite gravity data, if applicable (see Fig. 2). Another advantage of including data by levels is that the high frequencies of the airborne data, which have large noise (Childers et al. 1999), could be excluded to guarantee a stable solution (Jiang and Wang 2016). Moreover, since the data are now introduced at the lower levels which require less grid points, the size of the design matrices, and consequently, the computation time is significantly reduced.
4 Validation with simulated data
4.1 Data
In the following, the MRR based on the pyramid algorithm is first realized and evaluated using simulated data to benefit from the availability of an accurate validation data set serving as the “truth”. The study area is between \(10^\circ \) and \(20^\circ \) longitude and between \(39^\circ \) and \(45^\circ \) latitude (Fig. 5), covering parts of South Europe, the Adriatic Sea, and the Tyrrhenian Sea. Five types of gravity observations are used, namely terrestrial, airborne, and altimetry data, as well as satellite data from GOCE and GRACE. These data are simulated from the global gravity model GECO (Gilardoni et al. 2016), with the position of the observations provided by the IAG-ICCT (International Association of Geodesy - Inter Commission Committee on Theory) Joint Study Group (JSG) 0.3 (“Comparison of current methodologies in regional gravity field modeling”), running from 2011 to 2015. All observations are simulated in the sense of disturbing gravity field quantities, i.e., functionals of the disturbing potential. A detailed data description can be found in Liu et al. (2020a). The terrestrial observations (yellow dots in Fig. 5) are generated on a regular grid at the surface of the topography (DTM2006.0, Pavlis et al. 2006) with a grid spacing of \(5'\) (which corresponds to a spatial resolution of 10 km). They are simulated up to spherical harmonic (SH) degree and order (d/o) 2190, in terms of the first order radial derivatives of the disturbing potential. The airborne data (red dots in Fig. 5) are located over the Adriatic Sea along synthetic flight tracks with an altitude of 2.5 km, generated in terms of the first order radial derivatives of the disturbing potential up to SH d/o 1600. The altimetry data (green dots in Fig. 5) are simulated up to SH d/o 1000 in terms of geoid height N, based on the real ground track of the altimetry mission Envisat (Extended Mission). The GOCE (grey dots in Fig. 5) and GRACE (blue dots in Fig. 5) data are simulated up to SH d/o 250, based on real satellite orbits with a time span of 61 days and one month, respectively. They are used in terms of the second-order radial derivatives of the disturbing potential for GOCE and the disturbing potential differences between the two satellites for GRACE. Observation noise is also generated and added to the gravity data, while the noise level is chosen according to the assumptions of the JSG 0.3. White noise with standard deviations of 0.01 mGal, 1 mGal, and 0.03 m is added to the terrestrial, airborne, and altimetry data, respectively. Colored noise (Austen and Grafarend 2004; Naeimi 2013) is added to the satellite data of GOCE and GRACE, with standard deviations of 10 mE and \(8\cdot 10^{-4}\ \text {m}^2/\text {s}^2\), respectively. Validation data are disturbing potential values simulated from GECO with a spatial resolution of \(5'\times 5'\) and a maximum degree of 2190.
4.2 Model configuration
In this study case, the highest resolution level of MRR is chosen as \(I=11\), considering the spatial resolution of the data (see Fig. 2). The terrestrial data are used at the highest level to calculate the unknown coefficients of this level following Eq. (16), with the expectation vector \(\varvec{\mu }\) set to the zero vector and the weight matrix \(\varvec{P}_{p,I}\) and \(\varvec{P}_\mu \) set to be the identity matrix \(\varvec{I}\) (Lieb et al. 2016; Liu et al. 2020a, b). As listed in Table 1, the airborne data are included at level 10, the altimetry data are then added at level 9, followed by the GOCE observations at level 8 and GRACE observations at level 7. The long-wavelength component (up to level 6) is modeled by the GGM within the RCR procedure, i.e., the background model GECO up to spherical harmonic degree \(n_6=2^6-1=63\) is removed from each observation, and then restored to the estimated model in the synthesis step. The single-level model and the MRR without the pyramid algorithm (see Sect. 1) are also calculated to serve as comparison scenarios. For the single-level model, all observations are combined at level 11, with the long-wavelength component (up to degree 63) modeled by GECO. For the MRR without pyramid algorithm, the unknown coefficients are estimated at each resolution level by combining all types of observations, and these coefficients are used to calculate the detail signals of each level. Wu et al. (2018) point out that the existing publications lack comparisons between the MRR and the single-level approach. Thus, the direct comparison of the single-level approach, the MRR without pyramid algorithm, and the MRR based on the pyramid algorithm, presented in this study fills this gap in current literature.
The Reuter grid is used, which generates a homogeneous coverage of equidistributed grid points on the sphere. The total number Z of Reuter grid points on the sphere is decided by a control parameter \(\gamma \), and \(\gamma +1\) denotes the number of points along the meridian (Eicker 2008). In this study, we choose the parameter \(\gamma \) to be equal to the maximum spectral degree \(n_i\) of the expansion at each resolution level i (Wittwer 2009; Bentel et al. 2013b). In regional gravity field modeling, the computation area \(\partial \Omega _C\), where the SRBFs are located, needs to be chosen larger than the observation area \(\partial \Omega _O\), where the observations are given (Fig. 5), and \(\partial \Omega _O\) needs to be larger than the investigation area \(\partial \Omega _I\), where the final gravity models are computed, i.e., \(\partial \Omega _C \supset \partial \Omega _O \supset \partial \Omega _I\). This hierarchy is necessary to mitigate edge effects. The margin size \(\eta _{C,O}\) between the computation area \(\partial \Omega _C\) and the observation area \(\partial \Omega _O\) is determined following (Lieb et al. 2016), with
where \(\varphi _{\max }\) is the maximum latitude value. The margin size is influenced by the shape of the SRBFs; they become wider at the lower resolution levels (i.e., when \(n_{\max }\) is smaller, see Fig. 3), and thus, a larger margin size has to be chosen to reduce edge effects (Liu et al. 2020b). In this case, the \(\eta _{C,O}\) is chosen as \(0.3^\circ , 0.6^\circ , 1.2^\circ , 2.4^\circ , 4.8^\circ \) for the levels 11, 10, 9, 8, 7, correspondingly (as shown in Fig. 6). Consequently, the number of unknown coefficients is decided by the generated Reuter grid points that are located inside the computation area \(\partial \Omega _C\) of each resolution level (which amounts to \(K_{11}=7759\), \(K_{10}=2238\), \(K_9=856\), \(K_8=326\), and \(K_7=157\)). In the single-level approach, the margin size \(\eta _{O,I}\) between the observation area \(\partial \Omega _O\) and the investigation area \(\partial \Omega _I\) is usually chosen the same as \(\eta _{C,O}\). For the MRR, multiple values of \(\eta _{C,O}\) are chosen for the different resolution levels. Numerical investigations in this work show that it is sufficient to choose the margin size \(\eta _{O,I}\) as the median of the applied \(\eta _{C,O}\) of each level, i.e., \(\eta _{O,I}=1.2^\circ \). Figure 5 (black rectangle) presents the corresponding investigation area \(\partial \Omega _I\).
In case of the MRR based on the pyramid algorithm, only specific observation groups are used at the higher resolution levels, which means the involved observations do not have full coverage over the observation area \(\partial \Omega _O\). This will cause strong edge effects at the border of the high-resolution observations in the calculated detail signals, and further contaminate the final gravity model. For example, at level 11, the terrestrial data are available only in the onshore area. Strong edge effects in \(\varvec{G}_{11}\) thus show up at the border of the terrestrial data coverage, i.e., near the coastal lines (as will be shown in Sect. 4.3). As pointed out by Lieb (2017), it is a challenging task to handle the edge effects properly in case of MRR, and it is one of the major difficulties in the practical realization of the pyramid algorithm. To address this issue, we develop a strategy in this study to reduce the edge effects in the calculated detail signals of each level. Besides the observation area \(\partial \Omega _O\) (Fig. 5) and the investigation area \(\partial \Omega _I\) (black rectangle in Fig. 5) for the whole study area, we also define \(\partial \Omega _{O_i}\) and \(\partial \Omega _{I_i}\) for each resolution level i when calculating the detail signals. To be more specific, \(\partial \Omega _{O_i}\) depends on the data coverage of the observation groups involved at this level, and \(\partial \Omega _{I_i}\) is adapted to \(\partial \Omega _{I_i}=\partial \Omega _{O_i} \cap \partial \Omega _I\). As an example, \(\partial \Omega _{O_{11}}\) is defined as the onshore areas in Fig. 5 since only terrestrial observations are involved at level 11. Consequently, \(\partial \Omega _{I_{11}}\) (see Fig. 7) is adapted to the onshore areas within the investigation area \(\partial \Omega _I\). The detail signals \(\varvec{G}_i\) of level i are then calculated within \(\partial \Omega _{I_i}\).
4.3 Modeling results and discussions
The estimated coefficients at each level are plotted in Fig. 6, and the black rectangle inside each plot represents the observation area \(\partial \Omega _O\) (Fig. 5). From the first row (level 11) to the fifth row (level 7), the margin size \(\eta _{C,O}\) increases and the number of unknown coefficients decreases. The top row shows the scaling coefficients \(\varvec{d}_{11}\) at level 11, which are estimated from the terrestrial observations only. Comparing the plot of \(\varvec{d}_{11}\) to Fig. 5, it is clear that the values of the coefficients are almost zero in the area where no terrestrial data exist, and larger absolute values are observed where these data are available. This shows that additional gravity information with respect to the background model is only captured at the locations with terrestrial data coverage, which is reasonable (Liu et al. 2020b). The left plot at the second row shows the scaling coefficients \(\varvec{d}_{10\mid 11}\) calculated directly from the pyramid algorithm, and the right one displays the updated coefficients \(\varvec{d}_{10}\) after including the airborne data at level 10. Comparing the two plots at level 10, we can see that the airborne observations insert additional gravity information in the region where they are located. They fill parts of the data gaps from the terrestrial data, and the gravity signals captured from the previous level (level 11) are preserved at the same time. At level 9 (third row), the same behavior as at level 10 can be observed, i.e., the altimetry data fill data gaps at the left bottom corner of the observation area, and meanwhile, the gravity signals from level 10 are kept. At level 8 (fourth row) and level 7 (fifth row), the satellite data which have even distributions are used. It can be observed that the right plots show darker colors (larger values) than the left ones inside the observation area \(\partial \Omega _O\), which indicate the contribution of the GOCE and GRACE data at level 8 and level 7, respectively.
Figure 7 (left column) visualizes the detail signals \(\varvec{G}_i\) of the MRR based on the pyramid algorithm at each level, which show the spectral information contained in the corresponding frequency ranges (see Fig. 2). At level 11, the detail signal \(\varvec{G}_{11}\) captures gravity information only in onshore area where the terrestrial data are located. However, at the border of the terrestrial data, strong edge effects show up. The same is valid in the detail signal \(\varvec{G}_{10}\) of level 10, large edge effects occur at the border of the data coverage, i.e., in the coastal area of the Tyrrhenian Sea. We thus apply the strategy explained in Sect. 4.2 to reduce these edge effects by defining \(\partial \Omega _{I_i}\), i.e., by setting \(\partial \Omega _{I_{11}}=\partial \Omega _{O_{11}} \cap \partial \Omega _I\) and \(\partial \Omega _{I_{10}}=\partial \Omega _{O_{10}} \cap \partial \Omega _I\). After level 9, the involved observations have full coverage over the observation area \(\partial \Omega _O\) (i.e., \(\partial \Omega _{I_i}=\partial \Omega _I\)), and no edge effects are visible within \(\partial \Omega _I\). Correspondingly, the new detail signals of level 11 and 10 after adapting \(\partial \Omega _{I_i}\) are presented in Fig. 7 (mid column), and the edge effects are significantly reduced. Figure 7 (right column) shows the gravity signal \(\varvec{F}_{I'}=\bar{\varvec{F}}+\sum _{i=7}^{I'} \varvec{G}_i\) of each level. The gravity signal (in terms of disturbing potential) of level 6 (\(\bar{\varvec{F}}\), right column, last row) is the long wavelength component from the global gravity model GECO, which only contains very smooth information. When the resolution level increases from level 7 (fifth row) to level 11 (first row), more and more fine structures show up in both the detail signals and the gravity signals.
The final modeling result (Fig. 7 right column, first row) is evaluated by the validation data, and their difference is visualized in Fig. 8d. For comparison, the single-level model, the MRR without pyramid algorithm, and the MRR based on pyramid algorithm before adapting the \(\partial \Omega _{I_i}\) are also computed, and their differences to the validation data are shown in Fig. 8a, b, and c, respectively. The corresponding statistics are listed in Table 2. As shown in Fig. 8a, the single-level model delivers small differences compared to the validation data in onshore regions, where the terrestrial data are available. However, in offshore regions with no terrestrial data coverage, the differences are quite large. This result demonstrates that the single-level approach majorly recovers gravity information from the terrestrial observations, and the contribution of other measurements which are sensitive to lower spectral bands is not captured sufficiently. It indicates that the single-level model is not able to benefit from all the observation types, as mentioned in the Introduction, and the MRR is necessary, especially in cases where the terrestrial data do not have large coverage over the study area. After applying the MRR, the differences w.r.t. the validation data in offshore regions decrease (see Fig. 8b), which indicates that the gravity information in lower-resolution observations are better extracted. The MRR without pyramid algorithm delivers an RMS error of 4.21 \(\text {m}^2/\text {s}^2\), which is 23% smaller than the one given by the single-level approach. However, Fig. 8b still shows the same pattern as the single-level model, i.e., larger differences show up in the offshore regions compared to the onshore regions. Although the MRR (without pyramid algorithm) already gives better results than the single-level approach, it is not optimal. Indeed, Lieb (2017) points out that the detail signals of different levels become correlated when all the observation groups are used at each level and recommends the implementation of the pyramid algorithm as further development of the MRR approach.
In case of the MRR based on the pyramid algorithm, as shown in Fig. 8d, the differences between the calculated gravity model and the validation data do not show dependency on the distribution of certain types of observations, i.e., the offshore area does not show larger differences than the area with terrestrial data. It suggests that each observation type makes a contribution to the final result, and the MRR benefits from all the measurements. This statement is supported by the fact that the RMS value delivered by the MRR based on the pyramid algorithm decreases by 50% w.r.t. the one delivered by the single-level approach, and 35% w.r.t. that of the MRR without pyramid algorithm. The comparison between Fig. 8d and Fig. 8c shows the benefit of applying the proposed strategy for reducing edge effects, i.e., by adapting the investigation area \(\partial \Omega _{I_i}\) at each level. The edge effects at the border (outside the coverage) of the terrestrial data are significantly reduced in Fig. 8d. The improvement achieved by applying this strategy is 21% in terms of RMS, w.r.t. the validation data. However, at the border (inside the coverage) of the terrestrial observations, the edge effects remain the same after adapting \(\partial \Omega _{I_i}\), as also shown in the calculated detail signals at level 11 and level 10 (Fig. 7, mid column). Thus, a main challenge to be faced in future studies regarding the MRR based on the pyramid algorithm is to further reduce these edge effects.
5 Validation with real data
5.1 Data and model configuration
After testing the performance of the MRR based on the pyramid algorithm with simulated data successfully, we apply this method to real data sets. Figure 9 shows the study area, located between \(5.9^\circ \) and \(14.3^\circ \) longitude and between \(53.2^\circ \) and \(55.3^\circ \) latitude, covering Northern Germany, parts of the North Sea and the Baltic Sea, and a small part of the Netherlands and Denmark. The gravity observations are taken from Lieb et al. (2016), where a detailed data description can be found. The terrestrial data (yellow dots in Fig. 9) are provided by the Federal States Schleswig-Holstein, Mecklenburg West-Pomerania, and Lower Saxony, with 23,465 observations covering Northern Germany. This high-resolution data set is given in terms of absolute gravity g and used in terms of gravity anomalies \(\Delta g\). Two airborne data sets (orange flight tracks in Fig. 9) are provided by the Federal Agency of Cartography and Geodesy (BKG), one over the North Sea, and another one over the Baltic Sea, collected in 2007/2008 and 2006, respectively. They have been pre-processed and are provided in terms of gravity disturbance \(\delta g\); the data accuracy is estimated by BKG to be 2 to 3 mGal. The flight campaign over the North Sea contains 5,651 observations, with an average flight altitude of 592 m; the flight campaign over the Baltic Sea contains 6,508 observations, with an average flight altitude of 832 m. The 1,183 shipborne measurements (red dots in Fig. 9) in the Baltic Sea are pre-processed and provided by the Federal State Mecklenburg West-Pomerania in terms of gravity anomalies \(\Delta g\). Satellite altimetry data (green dots in Fig. 9) are provided by the DGFI-TUM altimetry group in terms of geoid height N, which is derived from the measured sea surface heights (SSH) and the instantaneous dynamic ocean topography (iDOT) (Bosch et al. 2013). The altimetry data include measurements from multiple altimetry missions, namely the ERS-1e/f (Geodetic Mission phase, 1994–1995, cycles Nr. 139-143), Envisat (Extended Mission phase, 2010–2012, cycles Nr. 096-113), Jason-1 (Geodetic Mission phase, 2012–2013, cycles Nr. 500-537), and Cryosat (2010-2013, cycles Nr. 011-035), with an average spatial resolution of 10 km in the North Sea. In the Baltic Sea, we use a sparse altimetry data distribution deliberately in order to test our approach also in areas with poor data coverage. For each altimetry measurement, corrections derived from a multi-mission cross-calibration (Bosch et al. 2014) have been applied. The satellite data from GOCE and GRACE are included in this study case as the satellite-only global gravity model (GGM), instead of direct observations. Lieb et al. (2016) point out that the study area is too small (especially in the north–south direction) in comparison with the spatial resolution of the satellite data, and thus, does not allow resolving reliable long-wavelength information. In this way, we present the performance of the MRR based on the pyramid algorithm in two different scenarios of using the satellite data, i.e., as direct observations and as a satellite-only GGM, in the simulated (Sect. 4) and real case, respectively.
The highest resolution level of the MRR is chosen as \(I=12\) according to the spatial resolution of the data, and only the terrestrial data are used at the highest level to calculate the unknown coefficients of this level and to start the pyramid algorithm. The shipborne and the airborne data are included at level 11 and level 10, respectively, and the altimetry data are added at level 9. The long-wavelength component up to level 8 (degree 255) is modeled by using the RCR procedure with GOCO06s (Kvas et al. 2021), which enhances an optimal combination of the GOCE and GRACE data. Same as in the simulated case (see Sect. 4), we also calculate the single-level model and the MRR without the pyramid algorithm for comparison. The number of Reuter grid points at each level is determined in the same manner as for the simulated study case, and the margin size \(\eta _{C,O}\) between the computation area \(\partial \Omega _C\) and the observation area \(\partial \Omega _O\) is determined following Eq. (26). In this study case, the \(\eta _{C,O}\) is chosen as \(0.15^\circ , 0.3^\circ , 0.6^\circ , 1.2^\circ \) for levels 12, 11, 10, 9, correspondingly. Consequently, the number of unknown coefficients amounts to \(K_{12}=6638\), \(K_{11}=2111\), \(K_{10}=684\), and \(K_9=315\) at each resolution level. The margin size \(\eta _{O,I}\) between the observation area \(\partial \Omega _O\) and the investigation area \(\partial \Omega _I\) (black rectangle in Fig. 9) is chosen as the median of the applied \(\eta _{C,O}\), i.e., \(\eta _{O,I}=0.45^\circ \). As discussed in Sect. 4.2, strong edge effects show up in the calculated detail signals of the high resolution levels, due to the fact that the involved observations at these levels do not have full coverage over \(\partial \Omega _O\). Again, we apply the strategy proposed in Sect. 4.2, and define \(\partial \Omega _{I_i}=\partial \Omega _{O_i} \cap \partial \Omega _I\) for calculating the detail signals at each level. In the following, we always refer the MRR based on the pyramid algorithm to the one after adapting \(\partial \Omega _{I_i}\).
5.2 Modeling results and discussions
The elements of the estimated coefficient vectors \(\widehat{\varvec{d}}_i\) and their standard deviations at each level i are plotted in Fig. 10; the black rectangle inside each plot represents the observation area \(\partial \Omega _O\). As we can see, the estimated coefficients at level 12 only contain additional gravity information from the terrestrial data. Consequently, their standard deviations are much larger in regions without terrestrial observations, which is reasonable. At level 11, level 10, and level 9, the shipborne, airborne, and altimetry data insert additional information, respectively. The new observations introduced at the lower levels fill the data gaps from the terrestrial observations, and the features from the highest level are preserved at the same time. The behavior of the standard deviations coincides with the coefficients, i.e., from level 12 to level 10, the standard deviations at the locations with shipborne and airborne data decrease, and from level 10 to level 9, those within the altimetry data coverage decrease.
The computed regional quasi-geoid models from the single-level approach, the MRR without pyramid algorithm, and the MRR based on the pyramid algorithm (after adapting \(\partial \Omega _{I_i}\)) are firstly validated using GPS/leveling data in Northern Germany (Gruber et al. 2011). 53 data points are available within the investigation area \(\partial \Omega _I\) (black rectangle in Fig. 9), which are derived from GPS-based ellipsoidal heights and leveling-based normal heights. The differences between the computed height anomaly results and those from GPS/leveling are shown in Fig. 11, and the corresponding statistics are listed in Table 3. The mean value of the difference between the gravimetrically determined height anomalies and those from GPS/leveling amounts to around 33 cm. It is consistent with the value reported in Gruber et al. (2011)), and is caused by differences in the height system definition, i.e., the local normal heights in Germany refer to the vertical datum of the European Vertical Network (EUVN), which is defined as the equipotential surface of the Earth’s gravity field passing through the “Normaal Amsterdams Peil” (NAP; fundamental tide gauge in Amsterdam, the Netherlands). Figure 11 shows clearly that the MRR based on the pyramid algorithm delivers the smallest difference w.r.t. the GPS/leveling data, with an RMS error of 2.23 cm, which is 23% smaller than the one given by the MRR without pyramid algorithm, and 35% smaller than that of the single-level model. Such large improvements demonstrate the benefits of applying the MRR based on the pyramid algorithm. Figure 11a (single-level approach) and Fig. 11b (MRR without pyramid algorithm) show much larger differences w.r.t. the GPS/leveling data in comparison to Fig. 11c (MRR based on the pyramid algorithm), even in regions with very dense terrestrial data (between \(11^\circ \) and \(13.85^\circ \) longitude).
In the offshore area where no GPS/leveling data are available, the computed gravity models are validated with the \(2'\times 2'\) altimetric gravity anomaly grid DTU17 (Andersen and Knudsen 2019). The differences between the computed gravity anomaly results and the DTU17 are shown in Fig. 12, and the corresponding statistics are listed in Table 3. Again, the largest differences are delivered by the single-level approach (Fig. 12a), with an RMS error of 7.22 mGal. In the single-level model, much smaller differences show up in regions with shipborne data coverage (see Fig. 9), which suggests that it majorly recovers gravity information from the high-resolution shipborne data, and information from other measurement types are not captured sufficiently. This result agrees with the conclusion drawn from the simulated study case (see Sect. 4.3). In comparison to the single-level model, applying the MRR (without pyramid algorithm) improves the modeling results by 13%. Comparing Fig. 12b with Fig. 12a reveals significant improvements in regions where the altimetry data are located (between \(6.35^\circ \) and \(7^\circ \) longitude). This indicates that the MRR extracts gravity information from the lower resolution altimetry data better than the single-level approach. However, it can still be seen from Fig. 12b that larger differences occur in regions without shipborne data coverage. The differences w.r.t. the DTU17 are significantly reduced when the MRR based on the pyramid algorithm is applied, giving an RMS of 2.67 mGal, which is 57% smaller than the one delivered by the MRR without pyramid algorithm, and 63% smaller than that of the single-level approach. The improvement achieved by applying the MRR based on the pyramid algorithm is larger in the offshore area than in the onshore area, where high-resolution terrestrial data are available. It demonstrates that the single-level approach cannot represent the lower-resolution data in an optimal way, and the MRR based on the pyramid algorithm is beneficial, especially in regions where high-resolution gravity data are not available. In the MRR based on the pyramid algorithm (Fig. 12c), larger differences again occur at the border of the higher-resolution gravity data (shipborne and airborne), which is caused by edge effects, as discussed in Sect. 4.3.
It is worth mentioning that validation in the offshore area was also made w.r.t. the NKG2015 gravimetric quasi-geoid model (Ågren et al. 2016) to rule out possible conflicts when validating our results with external models also based on satellite altimetry data as the DTU17. The differences between the calculated quasi-geoid results and the NKG2015 model show the same pattern as those w.r.t. the DTU17, i.e., Fig. 12. Thus, this comparison is not shown in detail here due to the length of the manuscript. In comparison to the NKG2015, the improvement achieved by applying the developed MRR scheme based on the pyramid algorithm is 39% w.r.t. the MRR without pyramid algorithm, and it reaches 55% w.r.t. the single-level approach, in terms of RMS value.
6 Conclusion and outlook
This study focuses on the spectral combination of different types of gravity observations through the MRR based on the pyramid algorithm, which is realized successfully for the first time in connection with sequential parameter estimation, in regional gravity field modeling. We address in this paper the challenges regarding the practical realization of the pyramid algorithm. Firstly, a successive low-pass filtering for transforming the estimated coefficients of the highest resolution level to lower resolution levels is proposed. Furthermore, we develop an innovative MRR scheme where the coefficients for calculating the detail signals at each lower resolution level are not only determined from the pyramid algorithm but also updated by a direct combination with observation groups included according to their spectral resolution. The main contribution of our approach is that the final gravity model is able to benefit from the individual strengths of each observation type. The settings of the MRR are characterized, including the type of the SRBFs, the location of the SRBFs, and the margin size applied at each level. When the MRR based on the pyramid algorithm is applied, only specific data sets are used at the higher resolution levels, resulting in strong edge effects at the border of the high-resolution observations. Therefore, we additionally develop a suitable strategy to adapt the investigation area \(\partial \Omega _{I_i}\) at each level i according to the coverage of involved observations. This is also a remarkable innovation of our approach as it reduces edge effects in the calculated detail signals (and therefore, the final gravity model) significantly.
The performance of the MRR based on the pyramid algorithm is evaluated in comparison to the conventional single-level approach and the MRR without pyramid algorithm using both simulated and real gravity data. In the simulated study case, the RMS obtained by the MRR based on the pyramid algorithm is 50% smaller than the one delivered by the single-level approach, and 35% smaller than the one given by the MRR without pyramid algorithm, comparing to the validation data. Moreover, the single-level model shows very large differences to the validation data in offshore regions, which indicates that the contribution of other types of observations is not captured as sufficiently as the terrestrial observations. This shows that the single-level approach is biased towards the terrestrial measurements, and the gravity information from measurements with medium to low resolution is not extracted sufficiently. Applying the MRR (without pyramid algorithm) improves the modeling results in offshore regions. However, it still shows larger differences w.r.t. the validation data in the offshore area in comparison to the onshore area. Thus, it is important and beneficial to apply the MRR based on the pyramid algorithm, especially when the high-resolution terrestrial data do not have full coverage over the study area.
In the real data case, the MRR based on the pyramid algorithm is applied for regional gravity field modeling in Northern Germany. The terrestrial, shipborne, airborne, and altimetry observations are used at the resolution levels 12, 11, 10, and 9, respectively. At the lower levels, the gravity information obtained from the highest level is preserved, and at the same time, the new observations introduced at this specific level contribute with additional information and fill data gaps. Such features in the estimated coefficients are observed in both the simulated and real data cases. The computed gravity models are validated in terms of quasi-geoid and gravity anomaly with GPS/leveling data in land and the DTU17 in offshore area, respectively. In comparison to the single-level approach, the improvement achieved by the MRR based on the pyramid algorithm is 35% and 63% in terms of RMS value, w.r.t. the GPS/leveling data and DTU17, respectively. Compared with the MRR without pyramid algorithm, the RMS error obtained by the MRR based on the pyramid algorithm decreases by 23% and 57% w.r.t. the GPS/leveling data and DTU17, respectively. Such significant improvements further demonstrate the benefits of the MRR based on the pyramid algorithm. Results in the real case again show that both the single-level approach and the MRR without pyramid algorithm cannot recover gravity information from the lower-resolution observations as sufficient as the MRR based on the pyramid algorithm.
In both the simulated and the real cases, larger differences w.r.t. the validation data in the MRR based on the pyramid algorithm occur at the border of the high-resolution data, due to edge effects. Thus, a major concern for future work is to develop strategies for further reducing the edge effects in the calculated detail signals. We also plan to include the full variance-covariance matrix of the GGM. In current studies, the weight matrix of the prior information (used at the highest level) is defined as the identity matrix, which is computationally easy. However, better and more realistic modeling results might be obtained by considering the full covariance matrix of the GGM instead of a simple identity matrix. In addition, it is also planned for future work to use real GOCE gravity gradients and K-band range-rate (KBRR) data from GRACE as direct observations in our developed MRR scheme.
Data Availability
The terrestrial, airborne, and shipborne gravity data in North Germany were provided by the Federal Angency of Cartography and Geodesy (BKG) and the federal states Schleswig-Holstein, Mecklenburg West-Pomerania, and Lower Saxony. The altimetry data were generated by DGFI-TUM and are freely available through https://openadb.dgfi.tum.de/. The global gravity models can be publicly accessed from http://icgem.gfz-potsdam.de/. The DTU17 grid is downloaded from https://ftp.space.dtu.dk/pub/DTU17/, and the NKG2015 gravimetric quasi-geoid model is freely accessible through the International Service for the Geoid https://www.isgeoid.polimi.it/.
References
Ågren J, Strykowski G, Bilker-Koivula M, Omang O, Märdla S, Forsberg R, Ellmann A, Oja T, Liepins I, Parseliunas E, Kaminskis J, Sjöberg L, Valsson G (2016) The NKG2015 gravimetric geoid model for the Nordic-Baltic region. In: 1st Joint Commission 2 and IGFS Meeting International Symposium on Gravity, Geoid and Height Systems, pp 19–23, https://doi.org/10.13140/RG.2.2.20765.20969
Andersen O, Knudsen P (2019) The DTU17 global marine gravity field: First validation results. In: Fiducial reference measurements for altimetry. Springer, pp 83–87, https://doi.org/10.1007/1345_2019_65
Austen G, Grafarend E (2004) Gravitational field recovery from GRACE data of type high-low and low-low SST. In: Proceedings of the Joint CHAMP/GRACE science meeting
Bentel K, Schmidt M, Denby CR (2013a) Artifacts in regional gravity representations with spherical radial basis functions. J Geod Sci 3:173–187. https://doi.org/10.2478/jogs-2013-0029
Bentel K, Schmidt M, Gerlach C (2013b) Different radial basis functions and their applicability for regional gravity field representation on the sphere. Int J Geomath 4:67–96. https://doi.org/10.1007/s13137-012-0046-1
Beylkin G, Cramer R (2002) Toward multiresolution estimation and efficient representation of gravitational fields. Celest Mech Dyn Astron 84(1):87–104. https://doi.org/10.1023/A:1019941111529
Bolkas D, Fotopoulos G, Braun A (2016) Comparison and fusion of satellite, airborne, and terrestrial gravity field data using wavelet decomposition. J Surv Eng 142(2):04015010. https://doi.org/10.1061/(ASCE)SU.1943-5428.0000162
Bosch W, Dettmering D, Schwatke C (2014) Multi-mission cross-calibration of satellite altimeters: constructing a long-term data record for global and regional sea level change studies. Remote Sens 6(3):2255–2281. https://doi.org/10.3390/rs6032255
Bosch W, Savcenko R, Dettmering D, Schwatke C (2013) A two-decade time series of eddy-resolving dynamic ocean topography (iDOT). In: Ouwehand L (ed) Proceedings of “20 Years of Progress in Radar Altimetry”, Sept. 2012, Venice, Italy, ESA SP-710 (CD-ROM), ESA/ESTEC. ISBN 978-92-9221-274-2
Bucha B, Janák J, Papčo J, Bezděk A (2016) High-resolution regional gravity field modelling in a mountainous area from terrestrial gravity data. Geophys J Int 207:949–966. https://doi.org/10.1093/gji/ggw311
Childers VA, Bell RE, Brozena JM (1999) Airborne gravimetry: an investigation of filtering. Geophysics 64:61–69. https://doi.org/10.1190/1.1444530
Denker H (2013) Regional gravity field modeling: theory and practical results. In: Sciences of geodesy-II. Springer, pp 185–291, https://doi.org/10.1007/978-3-642-28000-9_5
Eicker A (2008) Gravity field refinement by radial basis functions from in-situ satellite data. PhD thesis, Universität Bonn
Erdogan E, Schmidt M, Goss A, Görres B, Seitz F (2020) Adaptive modeling of the global ionosphere vertical total electron content. Remote Sens 12(11):1822. https://doi.org/10.3390/rs12111822
Fengler M, Freeden W, Kohlhaas A, Michel V, Peters T (2007) Wavelet modeling of regional and temporal variations of the Earth’s gravitational potential observed by GRACE. J Geodesy 81(1):5–15. https://doi.org/10.1007/s00190-006-0040-1
Fengler M, Freeden W, Michel V (2004) The Kaiserslautern multiscale geopotential model SWITCH-03 from orbit perturbations of the satellite CHAMP and its comparison to the models EGM96, UCPH2002_02_0.5, EIGEN-1s and EIGEN-2. Geophys J Int 157(2):499–514. https://doi.org/10.1111/j.1365-246X.2004.02209.x
Forsberg R (1993) Modelling the fine-structure of the geoid: methods, data requirements and some results. Surv Geophys 14(4–5):403–418. https://doi.org/10.1007/BF00690568
Freeden W (1999) Multiscale modelling of spaceborne geodata. Teubner, Stuttgart
Freeden W, Michel V (2004) Multiscale potential theory: with applications to geoscience. Birkhäuser, Basel
Freeden W, Gervens T, Schreiner M (1998) Constructive approximation on the sphere with applications to geomathematics. Oxford University Press on Demand, New York
Gilardoni M, Reguzzoni M, Sampietro D (2016) GECO: a global gravity model by locally combining GOCE data and EGM2008. Stud Geophys Geod 60(2):228–247. https://doi.org/10.1007/s11200-015-1114-4
Gruber T, Visser P, Ackermann C, Hosse M (2011) Validation of goce gravity field models by means of orbit residuals and geoid comparisons. J Geodesy 85(11):845–860. https://doi.org/10.1007/s00190-011-0486-7
Haagmans R, Prijatna K, Omang O (2002) An alternative concept for validation of GOCE gradiometry results based on regional gravity. In: Tziavos N (ed) Proceedings of the 3rd meeting of the international gravity and geoid commission, Ziti Editions, pp 281–286
Holschneider M, Chambodut A, Mandea M (2003) From global to regional analysis of the magnetic field on the sphere using wavelet frames. Phys Earth Planet Inter 135(2–3):107–124. https://doi.org/10.1016/S0031-9201(02)00210-8
Jiang T, Wang YM (2016) On the spectral combination of satellite gravity model, terrestrial and airborne gravity data for local gravimetric geoid computation. J Geodesy 90:1405–1418. https://doi.org/10.1007/s00190-016-0932-7
Kalman RE (1960) A new approach to linear filtering and prediction problems. J Basic Eng 82(1):35–45. https://doi.org/10.1115/1.3662552
Kern M, Schwarz K, Sneeuw N (2003) A study on the combination of satellite, airborne, and terrestrial gravity data. J Geodesy 77(3–4):217–225. https://doi.org/10.1007/s00190-003-0313-x
Klees R, Slobbe D, Farahani H (2018) A methodology for least-squares local quasi-geoid modelling using a noisy satellite-only gravity field model. J Geodesy 92:431–442. https://doi.org/10.1007/s00190-017-1076-0
Koch KR (1999) Parameter estimation and hypothesis testing in linear models. Springer Berlin Heidelberg, Berlin
Koch KR, Kusche J (2002) Regularization of geopotential determination from satellite data by variance components. J Geodesy 76:259–268. https://doi.org/10.1007/s00190-002-0245-x
Koop R (1993) Global gravity field modelling using satellite gravity gradiometry. Nederlandse Commissie voor Geodesie, Delft
Kusche J, Ilk K, Rudolph S, Thalhammer M (1998) Application of spherical wavelets for regional gravity field recovery - a comparative study. In: Geodesy on the Move, Springer, pp 213–218, https://doi.org/10.1007/978-3-642-72245-5_30
Kvas A, Brockmann JM, Krauss S, Schubert T, Gruber T, Meyer U, Mayer-Gürr T, Schuh WD, Jäggi A, Pail R (2021) GOCO06s—a satellite-only global gravity field model. Earth Syst Sci Data 13(1):99–118. https://doi.org/10.5194/essd-13-99-2021
Lieb V (2017) Enhanced regional gravity field modeling from the combination of real data via MRR. PhD thesis, Technische Universität München
Lieb V, Schmidt M, Dettmering D, Börger K (2016) Combination of various observation techniques for regional modeling of the gravity field. J Geophys Res Solid Earth 121:3825–3845. https://doi.org/10.1002/2015JB012586
Liu Q, Schmidt M, Pail R, Willberg M (2020a) Determination of the regularization parameter to combine heterogeneous observations in regional gravity field modeling. Remote Sens 12(10):1617. https://doi.org/10.3390/rs12101617
Liu Q, Schmidt M, Sánchez L, Willberg M (2020b) Regional gravity field refinement for (quasi-) geoid determination based on spherical radial basis functions in Colorado. J Geodesy 94(10):1–19. https://doi.org/10.1007/s00190-020-01431-2
Naeimi M (2013) Inversion of satellite gravity data using spherical radial base functions. PhD thesis, Leibniz Universität Hannover
Panet I, Kuroishi Y, Holschneider M (2011) Wavelet modelling of the gravity field by domain decomposition methods: an example over Japan. Geophys J Int 184(1):203–219. https://doi.org/10.1111/j.1365-246X.2010.04840.x
Pavlis NK, Factor JK, Holmes SA (2006) Terrain-related gravimetric quantities computed for the next EGM. In: Proceedings of the 1st International Symposium of the International Gravity Field Service (IGFS), Istanbul, pp 318–323
Reuter R (1982) Über Integralformeln der Einheitssphäre und harmonische Splinefunktionen. PhD thesis, RWTH Aachen University
Rummel R, Balmino G, Johannessen J, Visser P, Woodworth P (2002) Dedicated gravity field missions - principles and aims. J Geodyn 33:3–20. https://doi.org/10.1016/S0264-3707(01)00050-3
Sánchez L, Ågren J, Huang J, Wang YM, Mäkinen J, Pail R, Barzaghi R, Vergos GS, Ahlgren K, Liu Q (2021) Strategy for the realisation of the International Height Reference System (IHRS). J Geodesy 95(3):1–33. https://doi.org/10.1007/s00190-021-01481-0
Schmidt M, Fabert O, Shum C (2005) On the estimation of a multi-resolution representation of the gravity field based on spherical harmonics and wavelets. J Geodyn 39(5):512–526. https://doi.org/10.1016/j.jog.2005.04.007
Schmidt M, Han SC, Kusche J, Sanchez L, Shum C (2006) Regional high-resolution spatiotemporal gravity modeling from GRACE data using spherical wavelets. Geophys Res Lett. https://doi.org/10.1029/2005GL025509
Schmidt M, Fengler M, Mayer-Gürr T, Eicker A, Kusche J, Sánchez L, Han SC (2007) Regional gravity modeling in terms of spherical base functions. J Geodesy 81:17–38. https://doi.org/10.1007/s00190-006-0101-5
Schmidt M, Göttl F, Heinkelmann R (2015) Towards the combination of data sets from various observation techniques. In: Kutterer H, Seitz F, Alkhatib H, Schmidt M (eds) The 1st International Workshop on the Quality of Geodetic Observation and Monitoring Systems (QuGOMS’11), Springer, pp 35–43, https://doi.org/10.1007/978-3-319-10828-5_6
Sjöberg L (1981) Least-squares combination of satellite and terrestrial data in physical geodesy. Ann Geophys 37:25–30
Tapley BD, Bettadpur S, Watkins M, Reigber C (2004) The gravity recovery and climate experiment: mission overview and early results. Geophys Res Lett. https://doi.org/10.1029/2004GL019920
Wittwer T (2009) Regional gravity field modelling with radial basis functions. PhD thesis, Netherlands Geodetic Commission
Wu Y, Luo Z, Chen W, Chen Y (2017a) High-resolution regional gravity field recovery from Poisson wavelets using heterogeneous observational techniques. Earth Planets Space 69:34. https://doi.org/10.1186/s40623-017-0618-2
Wu Y, Zhou H, Zhong B, Luo Z (2017b) Regional gravity field recovery using the GOCE gravity gradient tensor and heterogeneous gravimetry and altimetry data. J Geophys Res Solid Earth 122(8):6928–6952. https://doi.org/10.1002/2017JB014196
Wu Y, Luo Z, Zhong B, Xu C (2018) A multilayer approach and its application to model a local gravimetric quasi-geoid model over the North Sea: QGNSea V1.0. Geosci Model Dev 11(12):4797–4815. https://doi.org/10.5194/gmd-11-4797-2018
Acknowledgements
The authors would like to thank the German Research Foundation (DFG) for funding the project “Optimally combined regional geoid models for the realization of height systems in developing countries” (grant number: SCHM 2433/11-1). We thank the Federal Angency of Cartography and Geodesy (BKG) and the federal states Schleswig-Holstein, Mecklenburg West-Pomerania, and Lower Saxony for providing us the terrestrial, airborne, and shipborne data sets. We thank Dr. Thomas Gruber from IAPG-TUM for kindly providing the GPS/leveling data in North Germany. Furthermore, the authors acknowledge the developers of the Generic Mapping Tool (GMT) mainly used for generating the figures in this work. Finally, we thank the reviewers and editors for their comments that helped us to significantly improve the manuscript.
Funding
Open Access funding enabled and organized by Projekt DEAL. This research was funded by the German Research Foundation (DFG) under grant number SCHM 2433/11-1 (project ORG4Heights).
Author information
Authors and Affiliations
Contributions
The concept of the paper was proposed by QL. QL designed the study, performed the calculations, compiled the figures, and wrote the manuscript with the assistance from MS. All authors edited, reviewed, and commented on the original manuscript.
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Liu, Q., Schmidt, M. & Sánchez, L. Combination of different observation types through a multi-resolution representation of the regional gravity field using the pyramid algorithm and parameter estimation. J Geod 96, 80 (2022). https://doi.org/10.1007/s00190-022-01670-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s00190-022-01670-5