Abstract
Additive Manufacturing technology has a significant impact on the modern world because of its ability to fabricate highly complex computerized geometrics. Pure 3D-printed polymer parts have limited potential applications due to inherently inferior mechanical and anisotropic properties. For more utilization and versatility, the addition of fillers has enhanced their functionalities. 3D printing has innovative advantages including low cost, minimal wastage, customized geometry, and ease of material change. This review reveals the development of 3D printing techniques of matrix composite materials with improving properties and their applications in the fields of aerospace, automotive, biomedical, and electronics. A general introduction is given on AM techniques mainly fused deposition modeling (FDM), Powder-liquid 3D printing (PLP), selective laser sintering (SLS), stereolithography (SLA), digital light processing (DLP), and robocasting. Process methodologies and behavior of different filler additives, reinforcement fibers, nanoparticles, and ceramic polymer composites are discussed. Also, some major issues of difficulty including printing parameters, homogeneous desperation of fillers, nozzle clogging due to filler aggregation, void formation, augmented curing time, and anisotropic attributes are addressed. In the end, some capabilities and shortcomings are pointed out for further development of 3D-printing technology.
Similar content being viewed by others
References
Standard A (2012) F2792, 2012. Standard terminology for additive manufacturing technologies. ASTM, West Conshohocken
Kodama H (1981) Automatic method for fabricating a three-dimensional plastic model with photo-hardening polymer. Rev Sci Instrum 52(11):1770–1773
Hull CW (1986) Apparatus for production of three-dimensional objects by stereolithography. Google Patents,
Levy GN, Schindel R, Kruth J-P (2003) Rapid manufacturing and rapid tooling with layer manufacturing (LM) technologies, state of the art and future perspectives. CIRP Ann Manuf Technol 52(2):589–609
Melnikova R, Ehrmann A 2014, Finsterbusch K 3D printing of textile-based structures by Fused Deposition Modelling (FDM) with different polymer materials. In: IOP Conference Series: Materials Science and Engineering, vol 1. IOP Publishing, p 012018
Tran P, Ngo TD, Ghazlan A, Hui D (2017) Bimaterial 3D printing and numerical analysis of bio-inspired composite structures under in-plane and transverse loadings. Compos Part B: Eng 108:210–223
Tymrak B, Kreiger M, Pearce JM (2014) Mechanical properties of components fabricated with open-source 3-D printers under realistic environmental conditions. Mater Des 58:242–246
Sun Q, Rizvi G, Bellehumeur C, Gu P (2008) Effect of processing conditions on the bonding quality of FDM polymer filaments. Rapid Prototyp J 14(2):72–80
Garcia CR, Correa J, Espalin D, Barton JH, Rumpf RC, Wicker R, Gonzalez V (2012) 3D printing of anisotropic metamaterials. Prog Electromagn Res 34:75–82
Caulfield B, McHugh P, Lohfeld S (2007) Dependence of mechanical properties of polyamide components on build parameters in the SLS process. J Mater Process Technol 182(1-3):477–488
Dou J, Zhang Q, Ma M, Gu J (2012) Fast fabrication of epoxy-functionalized magnetic polymer core-shell microspheres using glycidyl methacrylate as monomer via photo-initiated miniemulsion polymerization. J Magn Magn Mater 324(19):3078–3082
Gu H, Ma C, Gu J, Guo J, Yan X, Huang J, Zhang Q, Guo Z (2016) An overview of multifunctional epoxy nanocomposites. J Mater Chem C 4(25):5890–5906
Bletzinger K-U, Ramm E (2001) Structural optimization and form finding of light weight structures. Comp Struct 79(22-25):2053–2062
Wong KV, Hernandez A (2012) A review of additive manufacturing. ISRN Mech Eng 2012
Short DB (2015) Use of 3D printing by museums: educational exhibits, artifact education, and artifact restoration. 3D. Print Addit Manuf 2(4):209–215
Murphy SV, Atala A (2014) 3D bioprinting of tissues and organs. Nat Biotechnol 32(8):773–785
Fielding GA, Bandyopadhyay A, Bose S (2012) Effects of silica and zinc oxide doping on mechanical and biological properties of 3D printed tricalcium phosphate tissue engineering scaffolds. Dent Mater 28(2):113–122
Makovec R (2010) Digital technologies in dental laboratories. Annals of DAAAM & Proceedings:p1579
Suwanprateeb J, Sanngam R, Suvannapruk W, Panyathanmaporn T (2009) Mechanical and in vitro performance of apatite–wollastonite glass ceramic reinforced hydroxyapatite composite fabricated by 3D-printing. J Mater Sci Mater Med 20(6):1281–1289
Malhotra SK, Goda K, Sreekala MS (2012) Part one introduction to polymer composites. Polym Compos 1
Huang SH, Liu P, Mokasdar A, Hou L (2013) Additive manufacturing and its societal impact: a literature review. Int J Adv Manuf Technol 67(5-8):1191–1203
Mohamed OA, Masood SH, Bhowmik JL (2015) Optimization of fused deposition modeling process parameters: a review of current research and future prospects. Adv Manuf 3(1):42–53
Majeed A, Lv J, Peng T (2019) A framework for big data driven process analysis and optimization for additive manufacturing. Rapid Prototyp J 25(2):308–321. https://doi.org/10.1108/RPJ-04-2017-0075
Parandoush P, Lin D (2017) A review on additive manufacturing of polymer-fiber composites. Compos Struct 182:36–53
Wang X, Jiang M, Zhou Z, Gou J, Hui D (2017) 3D printing of polymer matrix composites: A review and prospective. Compos Part B: Eng 110:442–458
Noorani R (2006) Rapid prototyping: principles and applications.
Cooper KG (2001) Rapid prototyping technology, vol 200. Marcel Dekker New York, New York
Mançanares CG, Zancul ES, da Silva JC, Miguel PAC (2015) Additive manufacturing process selection based on parts’ selection criteria. Int J Adv Manuf Technol 80(5-8):1007–1014
Cho Y, Lee I, Cho D-W (2005) Laser scanning path generation considering photopolymer solidification in micro-stereolithography. Microsyst Technol 11(2-3):158–167
Diegel O, Withell A, de Beer D, Potgieter J, Noble FK (2012) Low-cost 3D printing of controlled porosity ceramic parts. IJAT 6(5):618–626
Halloran JW, Tomeckova V, Gentry S, Das S, Cilino P, Yuan D, Guo R, Rudraraju A, Shao P, Wu T (2011) Photopolymerization of powder suspensions for shaping ceramics. J Eur Ceram Soc 31(14):2613–2619
Utela B, Storti D, Anderson R, Ganter M (2008) A review of process development steps for new material systems in three dimensional printing (3DP). J Manuf Process 10(2):96–104
Gu D, Meiners W, Wissenbach K, Poprawe R (2012) Laser additive manufacturing of metallic components: materials, processes and mechanisms. Int Mater Rev 57(3):133–164
Lee H, Lim CHJ, Low MJ, Tham N, Murukeshan VM, Kim Y-J (2017) Lasers in additive manufacturing: a review. Int J Precis Eng Manuf-Green Technol 4(3):307–322
Brooks G, Kinsley K, Owens T (2014) 3D printing as a consumer technology business model. Int J Manag Inf Syst (Online) 18(4):271
Chia HN, Wu BM (2015) Recent advances in 3D printing of biomaterials. J Biol Eng 9(1):4
Billiet T, Vandenhaute M, Schelfhout J, Van Vlierberghe S, Dubruel P (2012) A review of trends and limitations in hydrogel-rapid prototyping for tissue engineering. Biomaterials 33(26):6020–6041
Postiglione G, Natale G, Griffini G, Levi M, Turri S (2015) Conductive 3D microstructures by direct 3D printing of polymer/carbon nanotube nanocomposites via liquid deposition modeling. Compos Part A Appl Sci Manuf 76:110–114
Edgar J, Tint S (2015) Additive manufacturing technologies: 3D printing, rapid prototyping, and direct digital manufacturing. Johnson Matthey Technol Rev 59(3):193–198
Cooperstein I, Layani M, Magdassi S (2015) 3D printing of porous structures by UV-curable O/W emulsion for fabrication of conductive objects. J Mater Chem C 3(9):2040–2044
Saari M, Cox B, Richer E, Krueger PS, Cohen AL (2015) Fiber encapsulation additive manufacturing: an enabling technology for 3D printing of electromechanical devices and robotic components. 3D. Print Addit Manuf 2(1):32–39
Ge Q, Dunn CK, Qi HJ, Dunn ML (2014) Active origami by 4D printing. Smart Materials and Structures 23(9):094007
Takezawa A, Kobashi M (2017) Design methodology for porous composites with tunable thermal expansion produced by multi-material topology optimization and additive manufacturing. Compos Part B Eng 131:21–29
Nikzad M, Masood S, Sbarski I (2011) Thermo-mechanical properties of a highly filled polymeric composites for fused deposition modeling. Mater Des 32(6):3448–3456
Hwang S, Reyes EI, K-s M, Rumpf RC, Kim NS (2015) Thermo-mechanical characterization of metal/polymer composite filaments and printing parameter study for fused deposition modeling in the 3D printing process. J Electron Mater 44(3):771–777
Ayrilmis N, Kariz M, Kwon JH, Kuzman MK (2019) Effect of printing layer thickness on water absorption and mechanical properties of 3D-printed wood/PLA composite materials. Int J Adv Manuf Technol 102(5-8):2195–2200
Boparai K, Singh R, Singh H (2015) Comparison of tribological behaviour for Nylon6-Al-Al2O3 and ABS parts fabricated by fused deposition modelling: this paper reports a low cost composite material that is more wear-resistant than conventional ABS. Virtual Phys Prototyp 10(2):59–66
Castles F, Isakov D, Lui A, Lei Q, Dancer C, Wang Y, Janurudin J, Speller S, Grovenor C, Grant PS (2016) Microwave dielectric characterisation of 3D-printed BaTiO3/ABS polymer composites. Sci Rep 6:22714
Shemelya CM, Rivera A, Perez AT, Rocha C, Liang M, Yu X, Kief C, Alexander D, Stegeman J, Xin H (2015) Mechanical, electromagnetic, and x-ray shielding characterization of a 3D printable tungsten–polycarbonate polymer matrix composite for space-based applications. J Electron Mater 44(8):2598–2607
Perez ART, Roberson DA, Wicker RB (2014) Fracture surface analysis of 3D-printed tensile specimens of novel ABS-based materials. J Fail Anal Prev 14(3):343–353
Martin JJ, Fiore BE, Erb RM (2015) Designing bioinspired composite reinforcement architectures via 3D magnetic printing. Nat Commun 6:8641
Kokkinis D, Schaffner M, Studart AR (2015) Multimaterial magnetically assisted 3D printing of composite materials. Nat Commun 6:8643
Chung H, Das S (2006) Processing and properties of glass bead particulate-filled functionally graded Nylon-11 composites produced by selective laser sintering. Mater Sci Eng: A 437(2):226–234
Kurimoto M, Yamashita Y, Ozaki H, Kato T, Funabashi T 2015, Suzuoki Y 3D printing of conical insulating spacer using alumina/UV-cured-resin composite. In: Electrical insulation and dielectric phenomena (CEIDP), IEEE Conference on, 2015. IEEE, pp 463-466
Kalsoom U, Peristyy A, Nesterenko P, Paull B (2016) A 3D printable diamond polymer composite: a novel material for fabrication of low cost thermally conducting devices. RSC Adv 6(44):38140–38147
Chung D (2001) Materials for thermal conduction. Appl Therm Eng 21(16):1593–1605
Ahn S-H, Montero M, Odell D, Roundy S, Wright PK (2002) Anisotropic material properties of fused deposition modeling ABS. Rapid Prototyp J 8(4):248–257
Guo N, Leu MC (2013) Additive manufacturing: technology, applications and research needs. Front Mech Eng 8(3):215–243. https://doi.org/10.1007/s11465-013-0248-8
Zhong W, Li F, Zhang Z, Song L, Li Z (2001) Short fiber reinforced composites for fused deposition modeling. Mater Sci Eng: A 301(2):125–130
Tekinalp HL, Kunc V, Velez-Garcia GM, Duty CE, Love LJ, Naskar AK, Blue CA, Ozcan S (2014) Highly oriented carbon fiber–polymer composites via additive manufacturing. Compos Sci Technol 105:144–150
Ning F, Cong W, Qiu J, Wei J, Wang S (2015) Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling. Compos Part B: Eng 80:369–378. https://doi.org/10.1016/j.compositesb.2015.06.013
Carneiro OS, Silva A, Gomes R (2015) Fused deposition modeling with polypropylene. Mater Des 83:768–776
Wang J, Xie H, Weng Z, Senthil T, Wu L (2016) A novel approach to improve mechanical properties of parts fabricated by fused deposition modeling. Mater Des 105:152–159
Shofner M, Lozano K, Rodríguez-Macías F, Barrera E (2003) Nanofiber-reinforced polymers prepared by fused deposition modeling. J Appl Polym Sci 89(11):3081–3090
Shofner M, Rodríguez-Macías F, Vaidyanathan R, Barrera E (2003) Single wall nanotube and vapor grown carbon fiber reinforced polymers processed by extrusion freeform fabrication. Compos Part A: Appl Sci Manuf 34(12):1207–1217
Le Duigou A, Castro M, Bevan R, Martin N (2016) 3D printing of wood fibre biocomposites: from mechanical to actuation functionality. Mater Des 96:106–114
Matsuzaki R, Ueda M, Namiki M, Jeong T-K, Asahara H, Horiguchi K, Nakamura T, Todoroki A, Hirano Y (2016) Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation. Sci Rep 6:23058
Li N, Li Y, Liu S (2016) Rapid prototyping of continuous carbon fiber reinforced polylactic acid composites by 3D printing. J Mater Process Technol 238:218–225
Nakagawa Y, K-i M, Maeno T (2017) 3D printing of carbon fibre-reinforced plastic parts. Int J Adv Manuf Technol 91(5-8):2811–2817
Zhong W, Li F, Zhang Z, Song L, Li Z (2001) Research on rapid-prototyping/part manufacturing (RP&M) for the continuous fiber reinforced composite. Mater Manuf Process 16(1):17–26
Compton BG, Lewis JA (2014) 3D-printing of lightweight cellular composites. Adv Mater 26(34):5930–5935
Van Der Klift F, Koga Y, Todoroki A, Ueda M, Hirano Y, Matsuzaki R (2015) 3D printing of continuous carbon fibre reinforced thermo-plastic (CFRTP) tensile test specimens. Open J Compos Mater 6(01):18
Goodridge R, Shofner M, Hague R, McClelland M, Schlea M, Johnson R, Tuck C (2011) Processing of a polyamide-12/carbon nanofibre composite by laser sintering. Polym Test 30(1):94–100
Love LJ, Kunc V, Rios O, Duty CE, Elliott AM, Post BK, Smith RJ, Blue CA (2014) The importance of carbon fiber to polymer additive manufacturing. J Mater Res 29(17):1893–1898
Ning F, Cong W, Jia Z, Wang F, Zhang M 2016 Additive manufacturing of CFRP composites using fused deposition modeling: effects of process parameters. In: ASME 2016 11th International Manufacturing Science and Engineering Conference. American Society of Mechanical Engineers, pp V003T008A001-V003T008A001
Griffini G, Invernizzi M, Levi M, Natale G, Postiglione G, Turri S (2016) 3D-printable CFR polymer composites with dual-cure sequential IPNs. Polymer 91:174–179
Namiki M, Ueda M, Todoroki A, Hirano Y, Matsuzaki R (2014) 3D printing of continuous fiber reinforced plastic. Proceedings of the Society of the Advancement of Material and Process Engineering (45):187-196
K-i M, Maeno T, Nakagawa Y (2014) Dieless forming of carbon fibre reinforced plastic parts using 3D printer. Procedia Eng 81:1595–1600
Chen H, Müller MB, Gilmore KJ, Wallace GG, Li D (2008) Mechanically strong, electrically conductive, and biocompatible graphene paper. Adv Mater 20(18):3557–3561
Gu J, Xie C, Li H, Dang J, Geng W, Zhang Q (2014) Thermal percolation behavior of graphene nanoplatelets/polyphenylene sulfide thermal conductivity composites. Polym Compos 35(6):1087–1092
Gu J, Li N, Tian L, Lv Z, Zhang Q (2015) High thermal conductivity graphite nanoplatelet/UHMWPE nanocomposites. RSC Adv 5(46):36334–36339
Wang FX, Yang Q, Zhou Z, Gou J 2014 Processing and characterization of helical carbon nanotube paper based thermoplastic nanocomposite films. In: Conference: CAMX, pp 1-9
Yan X, Gu J, Zheng G, Guo J, Galaska AM, Yu J, Khan MA, Sun L, Young DP, Zhang Q (2016) Lowly loaded carbon nanotubes induced high electrical conductivity and giant magnetoresistance in ethylene/1-octene copolymers. Polymer 103:315–327
Tang Y-S, Kong J, Gu J-W, Liang G-Z (2009) Reinforced cyanate ester resins with carbon nanotubes: surface modification, reaction activity and mechanical properties analyses. Polym-Plast Technol Eng 48(4):359–366
Lu H, Wang X, Yao Y, Gou J, Hui D, Xu B, Fu Y (2015) Synergistic effect of siloxane modified aluminum nanopowders and carbon fiber on electrothermal efficiency of polymeric shape memory nanocomposite. Compos Part B: Eng 80:1–6
Zhan H, Cheng F, Chen Y, Wong KW, Mei J, Hui D, Lau WM, Liu Y (2016) Transfer printing for preparing nanostructured PDMS film as flexible SERS active substrate. Compos Part B: Eng 84:222–227
Weng Z, Wang J, Senthil T, Wu L (2016) Mechanical and thermal properties of ABS/montmorillonite nanocomposites for fused deposition modeling 3D printing. Mater Des 102:276–283
Wei X, Li D, Jiang W, Gu Z, Wang X, Zhang Z, Sun Z (2015) 3D printable graphene composite. Sci Rep 5:11181
Hector Sandoval J, Wicker RB (2006) Functionalizing stereolithography resins: effects of dispersed multi-walled carbon nanotubes on physical properties. Rapid Prototyp J 12(5):292–303
Lin D, Jin S, Zhang F, Wang C, Wang Y, Zhou C, Cheng GJ (2015) 3D stereolithography printing of graphene oxide reinforced complex architectures. Nanotechnology 26(43):434003
Yugang D, Yuan Z, Yiping T, Dichen L (2011) Nano-TiO2-modified photosensitive resin for RP. Rapid Prototyp J 17(4):247–252
Kim K, Zhu W, Qu X, Aaronson C, McCall WR, Chen S, Sirbuly DJ (2014) 3D optical printing of piezoelectric nanoparticle–polymer composite materials. ACS Nano 8(10):9799–9806
Zhang Y, Li H, Yang X, Zhang T, Zhu K, Si W, Liu Z, Sun H (2018) Additive manufacturing of carbon nanotube-photopolymer composite radar absorbing materials. Polym Compos 39(S2):E671–E676
Athreya SR, Kalaitzidou K, Das S (2010) Processing and characterization of a carbon black-filled electrically conductive Nylon-12 nanocomposite produced by selective laser sintering. Mater Sci Eng: A 527(10-11):2637–2642
Zheng H, Zhang J, Lu S, Wang G, Xu Z (2006) Effect of core–shell composite particles on the sintering behavior and properties of nano-Al2O3/polystyrene composite prepared by SLS. Mater Lett 60(9-10):1219–1223
Kim HC, Hahn HT, Yang YS (2013) Synthesis of PA12/functionalized GNP nanocomposite powders for the selective laser sintering process. J Compos Mater 47(4):501–509
Lin D, Liu CR, Cheng GJ (2014) Single-layer graphene oxide reinforced metal matrix composites by laser sintering: microstructure and mechanical property enhancement. Acta Mater 80:183–193
Guo S-z, Yang X, Heuzey M-C, Therriault D (2015) 3D printing of a multifunctional nanocomposite helical liquid sensor. Nanoscale 7(15):6451–6456
Krivec M, Roshanghias A, Abram A, Binder A (2017) Exploiting the combination of 3D polymer printing and inkjet Ag-nanoparticle printing for advanced packaging. Microelectron Eng 176:1–5
Rymansaib Z, Iravani P, Emslie E, Medvidović-Kosanović M, Sak-Bosnar M, Verdejo R, Marken F (2016) All-polystyrene 3D-printed electrochemical device with embedded carbon nanofiber-graphite-polystyrene composite conductor. Electroanalysis 28(7):1517–1523
Elliott A, Ivanova O, Williams C, Campbell T (2012) An investigation of the effects of quantum dot nanoparticles on photopolymer resin for use in polyjet direct 3D printing. Proceedings of the 2012 SFF SSymposium
Chizari K, Daoud MA, Ravindran AR, Therriault D (2016) 3D Printing of highly conductive nanocomposites for the functional optimization of liquid sensors. Small 12(44):6076–6082
Chung H, Das S (2008) Functionally graded Nylon-11/silica nanocomposites produced by selective laser sintering. Mater Sci Eng: A 487(1-2):251–257
Chu T, Szczepkowski K, Wagner W, Halloran J Experimental ceramic suspensions for stereolithography processing of implants. In: Journal of Dental Research, 1996. AMER ASSOC DENTAL RESEARCH 1619 DUKE ST, ALEXANDRIA, VA 22314, pp 3046-3046
Giberti H, Strano M, Annoni M 2016 An innovative machine for fused deposition modeling of metals and advanced ceramics. In: MATEC web of conferences, EDP Sciences, p 03003
Khalyfa A, Vogt S, Weisser J, Grimm G, Rechtenbach A, Meyer W, Schnabelrauch M (2007) Development of a new calcium phosphate powder-binder system for the 3D printing of patient specific implants. J Mater Sci Mater Med 18(5):909–916
Shao H, He Y, Fu J, He D, Yang X, Xie J, Yao C, Ye J, Xu S, Gou Z (2016) 3D printing magnesium-doped wollastonite/β-TCP bioceramics scaffolds with high strength and adjustable degradation. J Eur Ceram Soc 36(6):1495–1503
Wu C, Luo Y, Cuniberti G, Xiao Y, Gelinsky M (2011) Three-dimensional printing of hierarchical and tough mesoporous bioactive glass scaffolds with a controllable pore architecture, excellent mechanical strength and mineralization ability. Acta Biomater 7(6):2644–2650
Seitz H, Rieder W, Irsen S, Leukers B, Tille C (2005) Three-dimensional printing of porous ceramic scaffolds for bone tissue engineering. J Biomed Mater Res Part B Appl Biomater 74(2):782–788
Detsch R, Schaefer S, Deisinger U, Ziegler G, Seitz H, Leukers B (2011) In vitro-osteoclastic activity studies on surfaces of 3D printed calcium phosphate scaffolds. J Biomater Appl 26(3):359–380
Zein I, Hutmacher DW, Tan KC, Teoh SH (2002) Fused deposition modeling of novel scaffold architectures for tissue engineering applications. Biomaterials 23(4):1169–1185
Bergmann C, Lindner M, Zhang W, Koczur K, Kirsten A, Telle R, Fischer H (2010) 3D printing of bone substitute implants using calcium phosphate and bioactive glasses. J Eur Ceram Soc 30(12):2563–2567
Lam CXF, Mo X, Teoh S-H, Hutmacher D (2002) Scaffold development using 3D printing with a starch-based polymer. Mater Sci Eng C 20(1-2):49–56
Zhou Z, Cunningham E, Lennon A, McCarthy HO, Buchanan F, Dunne N (2018) Development of three-dimensional printing polymer-ceramic scaffolds with enhanced compressive properties and tuneable resorption. Mater Sci Eng C 93:975–986
Vaezi M, Chua CK (2011) Effects of layer thickness and binder saturation level parameters on 3D printing process. Int J Adv Manuf Technol 53(1-4):275–284
Glasschroeder J, Prager E, Zaeh MF (2015) Powder-bed-based 3D-printing of function integrated parts. Rapid Prototyp J 21(2):207–215
Zanchetta E, Cattaldo M, Franchin G, Schwentenwein M, Homa J, Brusatin G, Colombo P (2016) Stereolithography of SiOC ceramic microcomponents. Adv Mater 28(2):370–376
Suwanprateeb J (2006) Improvement in mechanical properties of three-dimensional printing parts made from natural polymers reinforced by acrylate resin for biomedical applications: a double infiltration approach. Polym Int 55(1):57–62
Hui D, Goodridge R, Scotchford C, Grant D (2018) Laser sintering of nano-hydroxyapatite coated polyamide 12 powders. Addit Manuf 22:560–570
Schwentenwein M, Homa J (2015) Additive manufacturing of dense alumina ceramics. Int J Appl Ceram Technol 12(1):1–7
Zhang S, Miyanaji H, Yang L, Ali A, Dilip J 2014 An experimental study of ceramic dental porcelain materials using a 3D print (3DP) process. In: Proceeding of Solid Freeform Fabrication (SFF) Symposium, pp 991-1011
Bose S, Roy M, Bandyopadhyay A (2012) Recent advances in bone tissue engineering scaffolds. Trends Biotechnol 30(10):546–554
Wu S, Liu X, Yeung KW, Liu C, Yang X (2014) Biomimetic porous scaffolds for bone tissue engineering. Mater Sci Eng R Rep 80:1–36
Mota C, Puppi D, Chiellini F, Chiellini E (2015) Additive manufacturing techniques for the production of tissue engineering constructs. J Tissue Eng Regen Med 9(3):174–190
Butscher A, Bohner M, Hofmann S, Gauckler L, Müller R (2011) Structural and material approaches to bone tissue engineering in powder-based three-dimensional printing. Acta Biomater 7(3):907–920
Irsen SH, Leukers B, Höckling C, Tille C, Seitz H (2006) Bioceramic granulates for use in 3D printing: process engineering aspects. Materialwiss Werkst 37(6):533–537
White AA, Best SM, Kinloch IA (2007) Hydroxyapatite–carbon nanotube composites for biomedical applications: a review. Int J Appl Ceram Technol 4(1):1–13
Burguera EF, Xu HH, Takagi S, Chow LC (2005) High early strength calcium phosphate bone cement: effects of dicalcium phosphate dihydrate and absorbable fibers. J Biomed Mater Res Part A 75(4):966–975
Vaezi M, Seitz H, Yang S (2013) A review on 3D micro-additive manufacturing technologies. Int J Adv Manuf Technol 67(5-8):1721–1754
Campbell T, Williams C, Ivanova O, Garrett B (2011) Could 3D printing change the world. Technologies, Potential, and Implications of Additive Manufacturing, Atlantic Council, Washington:3
Wohlers T (2014) Tracking global growth in industrial-scale additive manufacturing. 3D. Print Addit Manuf 1(1):2–3
Liao Y, Li H, Chiu Y (2006) Study of laminated object manufacturing with separately applied heating and pressing. Int J Adv Manuf Technol 27(7-8):703–707
Invernizzi M, Natale G, Levi M, Turri S, Griffini G (2016) UV-assisted 3D printing of glass and carbon fiber-reinforced dual-cure polymer composites. Materials 9(7):583
Appleyard D (2015) Powering up on powder technology. Met Powder Rep 70(6):285–289
Watkins T, Bilheux H, An K, Payzant A, Dehoff R, Duty C, Peter W, Blue C, Brice CA (2013) Neutron characterization for additive manufacturing.
Bassett K, Carriveau R, Ting D-K (2015) 3D printed wind turbines part 1: Design considerations and rapid manufacture potential. Sustain Energy Technol Assess 11:186–193
Misra AK, Grady JE, Carter R (2015) Additive manufacturing of aerospace propulsion components.
Objects Impossible. http://impossible-objects.com/. Accessed 21/02/2019
Wang Y-C, Chen T, Yeh Y-L (2018) Advanced 3D printing technologies for the aircraft industry: a fuzzy systematic approach for assessing the critical factors. The International Journal of Advanced Manufacturing Technology:1-11
A world first: additively manufactured titanium components now onboard the Airbus A350 XWB. https://www.etmm-online.com/a-world-first-additively-manufactured-titanium-components-now-onboard-the-airbus-a350-xwb-a-486310/. Accessed 25/02/2019
Fit to print: new plant will assemble world’s first passenger jet engine with 3d printed fuel nozzles, Next-Gen Materials. https://www.ge.com/reports/post/80701924024/fit-to-print/. Accessed 25/02/2019.
Stratasys|3D printing solutions for aerospace. https://www.stratasys.com/aerospace. Accessed 25/02/2019
Grady JE, Haller WJ, Poinsatte PE, Halbig MC, Schnulo SL, Singh M, Weir D, Wali N, Vinup M, Jones MG (2015) A fully non-metallic gas turbine engine enabled by additive manufacturing part I: system analysis, component identification, additive manufacturing, and testing of polymer composites.
Kumar S, Kruth J-P (2010) Composites by rapid prototyping technology. Mater Des 31(2):850–856
Garcia-Gonzalez D, Garzon-Hernandez S, Arias A (2018) A new constitutive model for polymeric matrices: application to biomedical materials. Compos Part B Eng 139:117–129
Jardini AL, Larosa MA, Maciel Filho R, de Carvalho Zavaglia CA, Bernardes LF, Lambert CS, Calderoni DR, Kharmandayan P (2014) Cranial reconstruction: 3D biomodel and custom-built implant created using additive manufacturing. J Cranio Maxillofac Surg 42(8):1877–1884
Banks J (2013) Adding value in additive manufacturing: researchers in the United Kingdom and Europe look to 3D printing for customization. IEEE Pulse 4(6):22–26
Ackland DC, Robinson D, Redhead M, Lee PVS, Moskaljuk A, Dimitroulis G (2017) A personalized 3D-printed prosthetic joint replacement for the human temporomandibular joint: from implant design to implantation. J Mech Behav Biomed Mater 69:404–411
Driemel O, Braun S, Müller-Richter U, Behr M, Reichert T, Kunkel M, Reich R (2009) Historical development of alloplastic temporomandibular joint replacement after 1945 and state of the art. Int J Oral Maxillofac Surg 38(9):909–920
Johnson N, Roberts M, Doi S, Batstone M (2017) Total temporomandibular joint replacement prostheses: a systematic review and bias-adjusted meta-analysis. Int J Oral Maxillofac Surg 46(1):86–92
Ramos A, Mesnard M (2016) A new condyle implant design concept for an alloplastic temporomandibular joint in bone resorption cases. J Cranio Maxillofac Surg 44(10):1670–1677
Chen RK, Y-a J, Wensman J, Shih A (2016) Additive manufacturing of custom orthoses and prostheses—a review. Addit Manuf 12:77–89
Norman J, Madurawe RD, Moore CM, Khan MA, Khairuzzaman A (2017) A new chapter in pharmaceutical manufacturing: 3D-printed drug products. Adv Drug Deliver Rev 108:39–50
Xia Y, Zhou P, Cheng X, Xie Y, Liang C, Li C, Xu S (2013) Selective laser sintering fabrication of nano-hydroxyapatite/poly-ε-caprolactone scaffolds for bone tissue engineering applications. Int J Nanomed 8:4197
Dávila J, Freitas MSD, Inforçatti Neto P, Silveira ZDC, Silva JVLD, d’Ávila MA (2016) Fabrication of PCL/β-TCP scaffolds by 3D mini-screw extrusion printing. J Appl Polym Sci 133 (15)
Zhang J, Zhao S, Zhu M, Zhu Y, Zhang Y, Liu Z, Zhang C (2014) 3D-printed magnetic Fe 3 O 4/MBG/PCL composite scaffolds with multifunctionality of bone regeneration, local anticancer drug delivery and hyperthermia. J Mater Chem B 2(43):7583–7595
Jakus AE, Secor EB, Rutz AL, Jordan SW, Hersam MC, Shah RN (2015) Three-dimensional printing of high-content graphene scaffolds for electronic and biomedical applications. ACS Nano 9(4):4636–4648
Kang H-W, Lee SJ, Ko IK, Kengla C, Yoo JJ, Atala A (2016) A 3D bioprinting system to produce human-scale tissue constructs with structural integrity. Nature Biotechnol 34(3):312–319
Lee J-S, Hong JM, Jung JW, Shim J-H, Oh J-H, Cho D-W (2014) 3D printing of composite tissue with complex shape applied to ear regeneration. Biofabrication 6(2):024103
Mannoor MS, Jiang Z, James T, Kong YL, Malatesta KA, Soboyejo WO, Verma N, Gracias DH, McAlpine MC (2013) 3D printed bionic ears. Nano Lett 13(6):2634–2639
Duan B (2017) State-of-the-art review of 3D bioprinting for cardiovascular tissue engineering. Ann Biomed Eng 45(1):195–209
Markstedt K, Mantas A, Tournier I, Hc MÁ, Hägg D, Gatenholm P (2015) 3D bioprinting human chondrocytes with nanocellulose–alginate bioink for cartilage tissue engineering applications. Biomacromolecules 16(5):1489–1496
Keriquel V, Guillemot F, Arnault I, Guillotin B, Miraux S, Amédée J, Fricain J-C, Catros S (2010) In vivo bioprinting for computer-and robotic-assisted medical intervention: preliminary study in mice. Biofabrication 2(1):014101
Robbins JB, Gorgen V, Min P, Shepherd BR, Presnell SC (2013) A novel in vitro three-dimensional bioprinted liver tissue system for drug development. FASEB J 27(872):812
Zopf DA, Hollister SJ, Nelson ME, Ohye RG, Green GE (2013) Bioresorbable airway splint created with a three-dimensional printer. N Engl J Med 368(21):2043–2045
Macdonald E, Salas R, Espalin D, Perez M, Aguilera E, Muse D, Wicker RB (2014) 3D printing for the rapid prototyping of structural electronics. IEEE Access 2:234–242
Nassar IT, Tsang H, Church K, Weller TM A 2014 high efficiency, electrically-small, 3-D machined-substrate antenna fabricated with fused deposition modeling and 3-D printing. In: 2014 IEEE Radio and Wireless Symposium (RWS), IEEE, pp 67-69
Zhou W, List FA, Duty CE, Babu SS (2016) Fabrication of conductive paths on a fused deposition modeling substrate using inkjet deposition. Rapid Prototyp J 22(1):77–86
Joe Lopes A, MacDonald E, Wicker RB (2012) Integrating stereolithography and direct print technologies for 3D structural electronics fabrication. Rap Prototyp J 18(2):129–143
Lopes AJ, Lee IH, MacDonald E, Quintana R, Wicker R (2014) Laser curing of silver-based conductive inks for in situ 3D structural electronics fabrication in stereolithography. J Mater Process Technol 214(9):1935–1945
Palmer JA, Summers JL, Davis DW, Gallegos PL, Chavez BD, Yang P, Medina F, Wicker RB 2005 Realizing 3-D interconnected direct write electronics within smart stereolithography structures. In: ASME 2005 International Mechanical Engineering Congress and Exposition, American Society of Mechanical Engineers, pp 287-293
Perez KB, Williams CB 2013 Combining additive manufacturing and direct write for integrated electronics—a review. In: 24th International Solid Freeform Fabrication Symposium—An Additive Manufacturing Conference, SFF, pp 962-979
Wang J, Auyeung RC, Kim H, Charipar NA, Piqué A (2010) Three-dimensional printing of interconnects by laser direct-write of silver nanopastes. Adv Mater 22(40):4462–4466
Lind JU, Busbee TA, Valentine AD, Pasqualini FS, Yuan H, Yadid M, Park S-J, Kotikian A, Nesmith AP, Campbell PH (2017) Instrumented cardiac microphysiological devices via multimaterial three-dimensional printing. Nat Mater 16(3):303
Ahn BY, Duoss EB, Motala MJ, Guo X, Park S-I, Xiong Y, Yoon J, Nuzzo RG, Rogers JA, Lewis JA (2009) Omnidirectional printing of flexible, stretchable, and spanning silver microelectrodes. Science 323(5921):1590–1593
Leigh SJ, Bradley RJ, Purssell CP, Billson DR, Hutchins DA (2012) A simple, low-cost conductive composite material for 3D printing of electronic sensors. PloS One 7(11):e49365
Czyżewski J, Burzyński P, Gaweł K, Meisner J (2009) Rapid prototyping of electrically conductive components using 3D printing technology. J Mater Process Technol 209(12-13):5281–5285
Espalin D, Muse DW, MacDonald E, Wicker RB (2014) 3D Printing multifunctionality: structures with electronics. Int J Adv Manuf Technol 72(5-8):963–978
Ready S, Endicott F, Whiting GL, Ng TN, Chow EM, Lu J 2013 3D printed electronics. In: NIP & digital fabrication conference, vol 1. Society for Imaging Science and technology, pp 9-12
Aguilera E, Ramos J, Espalin D, Cedillos F, Muse D, Wicker R, MacDonald E 2013 3D printing of electro mechanical systems. In: Proceedings of the Solid Freeform Fabrication Symposium, pp 950-961
Sarik J, Butler A, Scott J, Hodges S, Villar N (2012) Combining 3D printing and printable electronics.
Yu Y-Z, Lu J-R, Liu J (2017) 3D printing for functional electronics by injection and package of liquid metals into channels of mechanical structures. Mater Des 122:80–89
Tanwilaisiri A, Xu Y, Zhang R, Harrison D, Fyson J, Areir M (2018) Design and fabrication of modular supercapacitors using 3D printing. J Energy Storage 16:1–7
Tilford T, Stoyanov S, Braun J, Janhsen JC, Burgard M, Birch R, Bailey C (2018) Design, manufacture and test for reliable 3D printed electronics packaging. Microelectron Reliab 85:109–117
Qiao H, Zhang Y, Huang Z, Wang Y, Li D, Zhou H (2018) 3D printing individualized triboelectric nanogenerator with macro-pattern. Nano Energy 50:126–132
Funding
This research was sponsored by National Natural Science Foundation of China (Grant No. 51905438), the Innovation Platform of Biofabrication (Grant No.17SF0002), the Fundamental Research Funds for the Central Universities (Grant No. 31020190502009, 31020190504002), and the key Research and Development Program of Shaanxi Province 2018 (Grant No. 2018ZDXM-GY-133).
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Saroia, J., Wang, Y., Wei, Q. et al. A review on 3D printed matrix polymer composites: its potential and future challenges. Int J Adv Manuf Technol 106, 1695–1721 (2020). https://doi.org/10.1007/s00170-019-04534-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-019-04534-z