Abstract
Hybrid laser–double-arc welding (HLDAW) is a perspective welding technology with high-deposition quantity, deep penetration, superior gap-bridging ability, and is simply equipped and flexibly adjusted. Either double-power supply system or single-power supply system can be used in this welding system. In the single-power supply mode, there is a particular phenomenon called “alternative burning” presented under certain welding conditions. The frequency of alternative burning is the key to the welding stability. However, the mechanism of this phenomenon and its change rules are not clear. This research mainly aims at the change laws of alternative burning and its essential mechanism. It was found that the alternating period is inversely proportional to laser power and wire-feeding speed, and is proportional to wire spacing and arc voltage. The essence of alternative burning is the regularly repetitive transfer of arc from one wire tip to the other in the condition of relatively low electron density in arc zone which is hard to maintain two arcs burning simultaneously. This phenomenon will disappear when the electron density is greater than 5.54 × 1016 cm−1. Results are meaningful for understanding the interaction mechanism of heat source and its influence on welding stability of HLDAW process in this kind of power supply.
Similar content being viewed by others
References
Dilthey U, Keller H (2001) Prospects in laser GMA hybrid welding of steel. Proceedings of the first international WLT-conference on lasers in manufacturing Munich June, pp 453–465
Olsen FO (2009) Hybrid laser–arc welding. Cambridge, U.K
Gu XY, Li H, Yang LJ, Gao Y (2013) Coupling mechanism of laser and arcs of laser-twin-arc hybrid welding and its effect on welding process. Opt Laser Technol 48:246–253
Hu LH, Huang J, Liu CT, Liu XL (2018) Effects of coupling between the laser plasma and two arcs on metal transfer in CO2 laser double-wire MIG hybrid welding. Opt Laser Technol 105:152–161
Gu XY, Li H, Jiang XB, Sheng HC (2017) Effect of laser on droplet transfer and welding process stability in hybrid laser + double arc welding. Int J Adv Manuf Technol 89:2981–2991
Moinuddin SQ, Sharma A (2015) Arc stability and its impact on weld properties and microstructure in anti-phase synchronised synergic-pulsed twin-wire gas metal arc welding. Mater Des 67:293–302
Bunaziv I, Frostevarg J, Akselsen OM (2018) Process stability during fiber laser-arc hybrid welding of thick steel plates. Opt Lasers Eng 102:34–44
Gao XD, Wang Y, Chen ZQ, Ma B (2018) Analysis of welding process stability and weld quality by droplet transfer and explosion in MAG-laser hybrid welding process. J Manuf Process 32:522–529
Greim HR (1964) Plasma spectroscopy. McGraw-Hill, US
Chen FF (1974) Introduction to plasma physics. Springer, US
NIST Atomic Spectra Database [DB/OL]. http://physics.nist.gov/PhysRefData/ASD/lines_form.html
Hoyaux MF (1968) Diagnostic techniques widely used in Arc Physics. Arc Physics:229–266
Di Y, Li H, Yang LJ, Gu XY, GAO Y (2013) Alternate arcing behavior of double-wire pulse MIG welding process with single power. Trans China Weld Inst 34(7):63–67
Wei HL, Li H, Yang LJ, Gao Y (2015) Arc characteristics and metal transfer process of hybrid laser double GMA welding. Int J Adv Manuf Technol 77:1019–1028
Li RF, Li ZG, Zhu YY, Rong L (2011) A comparative study of laser beam welding and laser MIG hybrid welding of Ti-Al-Zr-Fe titanium alloy. Mater Sci Eng 528:1138–1142
Xu GX, Li PF, Qingnan CQN, Hu QX, Gu XY, Du BS (2018) Modelling of fluid flow phenomenon in laser+GMAW hybrid welding of aluminum alloy considering three phase coupling and arc plasma shear stress. Opt Laser Technol 100:244–255
Chen J, Zong R, Wu C, Padhy GK, Hu Q (2017) Influence of low current auxiliary TIG arc on high speed TIG-MIG hybrid welding. J Mater Process Technol 243:131–142
Yan K, Su JS, Zhao Y (2017) Microstructure and mechanical properties of the laser-welded Mg-3Nd-0.2Zn-0.4Zr (NZ30K) magnesium alloy. Opt Laser Technol 93:109–117
Hu B, Ouden G (2005) Laser induced stabilization of the welding arc. Sci Technol Weld Join 10:76–81
Shinn BW, Farson DF, Denney PE (2005) Laser stabilization of arc cathode spots in titanium welding. Sci Technol Weld Join 10:475–481
Chen MH, Li XY, Liu LM (2012) Effect of electric field on interaction between laser and arc plasma in laser–arc hybrid welding. IEEE T Plasma Sci 40:2045–2050
Kiran DV, Cho DW, Song WH, Na SJ (2015) Arc interaction and molten pool behavior in the three wire submerged arc welding process. Int J Heat Mass Transf 87:327–340
Ueyama T, Ohnawa T, Tanaka M, Nakata K (2007) Occurrence of arc interaction in tandem pulsed gas metal arc welding. Sci Technol Weld Join 12(6):523–529
Funding
This research work was funded by National Natural Science Foundation of China (Grant No. 51705218).
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Gu, X., Di, Y. & Luo, J. Study on the alternative burning behavior of arcs in hybrid laser–double-arc welding. Int J Adv Manuf Technol 102, 2581–2590 (2019). https://doi.org/10.1007/s00170-019-03330-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-019-03330-z