Skip to main content
SpringerLink
Log in

Microstructure-property relation and evolution in friction stir welding of naturally aged 6063 aluminium alloy

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

The development of the microstructure and mechanical properties during friction stir welding of 6063-T4 aluminium alloy was investigated through electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) techniques and mechanical testing. Grain boundary and dislocation strengthening were observed to be the dominant strengthening mechanisms occurring in the stir zone (SZ). While the precipitates morphologies were sensitive to the weld zone temperatures, the grain size and grain boundary misorientations were related to strain (𝜖), strain rates (\(\dot {\epsilon }\)), and peak temperatures (T p ). Severe gradients in the crystallographic texture were observed at the top and bottom and on the retreating and advancing sides of the weld obtained at 48 mm/min welding speed. The optimal strength and ductility of a transverse tensile specimen were achieved when the cold defects, overaging in heat affected zones (HAZs), and grain size in stir zone (SZ) were minimized. While the yield strength of the longitudinal tensile specimens was controlled by the grain size, dislocation density and fraction of low angle boundaries (LABs), the uniform elongation was controlled by the fraction of high angle boundaries (HABs). In addition, a successful implementation of more simple geometry weld zone finite element model than earlier reported work for use in forming simulations was also proposed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Sevim I, Hayat F, Kaya Y, Kahraman N, Sahin S (2013) Study of MIG weldability of heat-treated aluminum alloys. Int J Adv Manuf Tech 66:1825–1834

    Article  Google Scholar 

  2. Diot G, Koudri-David A, Walaszek H, Guegan S, Flifla J (2013) Non-destructive testing of porosity in laser welded aluminium alloy plates: laser ultrasound and frequency-bandwidth analysis. J Nond Eval 32:354–361

    Article  Google Scholar 

  3. Rapp J, Glumann C, Dausinger F, Hogel H (1995) Laser welding of aluminium lightweight materials: problems, solutions, readiness for application. Opt Quan Elect 27:1203–1211

    Google Scholar 

  4. Mishra RS, Ma ZY (2005) Friction stir welding and processing. Mater Sci Eng R 50:1–78

    Article  Google Scholar 

  5. Mistikoglu CG (2014) Recent developments in friction stir welding of Al-alloys. J Mater Eng Perform 23:1936–1953

    Article  Google Scholar 

  6. Imam M, Ueji R, Fujii H (2016) Effect of online rapid cooling on microstructure and mechanical properties of friction stir welded medium carbon steel. J Mater Proc Tech 230:62–71

    Article  Google Scholar 

  7. Nandan R, Debroy T, Bhadeshia HKDH (2008) Recent advances in friction-stir welding - process, weldment structure and properties. Prog. Mater Sci 53(6):980–1023

    Article  Google Scholar 

  8. He X, Gu F, Ball A (2014) A review of numerical analysis of friction stir welding. Prog Mater Sci 65:1–65

    Article  Google Scholar 

  9. Murayama M, Hono K (1999) Pre-precipitate clusters and precipitation process in Al-Mg-Si alloys. Acta Mater 47(5):1537–48

    Article  Google Scholar 

  10. Heinz B, Skrotzki B (2002) Characterization of a friction-stir-welded aluminum alloy 6013. Metal Mater Trans B 33B:490–498

    Google Scholar 

  11. Simar A, Brechet Y, De Meester B, Denquin A, Gallais C, Pardoen T (2012) Integrated modeling of friction stir welding of 6XXX series Al alloys: process, microstructure and properties. Prog Mater Sci 57:95–183

    Article  Google Scholar 

  12. Liu FC, MA ZY (2008) Influence of tool dimension and welding parameters on microstructure and mechanical properties of friction-stir-welded 6061-T651aluminium alloy. Metal Mater Trans A 39A:2378–2388

    Article  Google Scholar 

  13. Imam M, Racherla V, Biswas K (2013) Effect of post-weld natural aging on mechanical and microstructural properties of friction stir welded 6063-T4 aluminium alloy. Mater Des 64:675–686

    Article  Google Scholar 

  14. Scialpi A, De Filippis LAC, Cavaliere P (2007) Influence of shoulder geometry on microstructure and mechanical properties of friction stir welded 6082 aluminium alloy. Mater Des 28:1124–1129

    Article  Google Scholar 

  15. Imam M, Racherla V, Biswas K (2015) Effect of backing plate material in friction stir butt and lap welding of 6063-T4 aluminium alloy. Int J Adv Manuf Tech 77(9):2181–2195

    Article  Google Scholar 

  16. Vidal C, Infante V (2013) Optimization of FS welding parameters for improving mechanical behavior of AA2024-T351 joints based on taguchi method. J Mater Eng Perform 22(8):2261–2270

    Google Scholar 

  17. Imam M, Biswas K, Racherla V (2014) Effect of weld morphology on mechanical response and failure of friction stir welds in a naturally aged aluminium alloy. Mater Des 44:23–34

    Article  Google Scholar 

  18. Rai R, De A, Bhadeshia HKDH, DebRoy T (2011) Review: friction stir welding tools. Sci Tech Weld Join 16(4):325– 342

    Article  Google Scholar 

  19. Colegrove PA, Shercliff HR (2004) Development of Trivex friction stir welding tool Part 1-two-dimensional flow modelling and experimental validation. Sci Tech Weld Join 9(4):345–351

    Article  Google Scholar 

  20. Fujii H, Cui L, Maeda M, Nogi K (2006) Effect of tool shape on mechanical properties and microstructure of friction stir welded aluminum alloys. Mater Sci Engg A 419:25–31

    Article  Google Scholar 

  21. Elangovan K, Balasubramanian V (2008) Influences of tool pin profile and welding speed on the formation of friction stir processing zone in AA2219 aluminium alloy. J Mater Proc Tech 200(1-3):163–175

    Article  Google Scholar 

  22. Cho H, Hong S, Roh J, Choi H, Kang SH, Steel RJ, Han HN (2013) Three-dimensional numerical and experimental investigation on friction stir welding processes of ferritic stainless steel. Act Mater 61:2649–2661

    Article  Google Scholar 

  23. Seidel TU, Reynolds AP (2003) Two-dimensional friction stir welding process model based on fluid mechanics. Sci Tech Weld Join 8(3):175–183

    Article  Google Scholar 

  24. Nandan R, Roy GG, Lienert TJ, Debroy T (2007) Three-dimensional heat and material flow during friction stir welding of mild steel. Act Mater 55:883–895

    Article  Google Scholar 

  25. Arbegast WJ, Hartley PJ (1998) Proceedings of the fifth international conference on trends in welding research, Pine Mountain, GA, USA, p 541

  26. Gholinia A, Humphreys FJ, Prangnell PB (2002) Production of ultra-fine grain microstructures in Al-Mg alloys by coventional rolling. Act Mater 50:4461–4476

    Article  Google Scholar 

  27. Hassan Kh AA, Prangnell PB, Norman AF, Price DA, Williams SW (2003) Effect of welding parameters on nugget zone microstructure and properties in high strength aluminium alloy friction stir welds. Sci Tech Weld Join 8(4):257–268

    Article  Google Scholar 

  28. Field DP, Nelson TW, Hovanski Y, Jata KV (2001) Heterogeneity of crystallographic texture in friction stir welds of Aluminum. Metal Mater Trans A 32a:2869–2877

    Article  Google Scholar 

  29. Hjelen J, Orsund R, Nes E (1990) On the origin of recrystallization textures in Aluminium. Act Mater 39(7):1377–1404

    Article  Google Scholar 

  30. Fonda RW, Bingert JF (2007) Texture variations in an aluminium friction stir weld. Scr Mater 57:1052–1055

    Article  Google Scholar 

  31. Fonda RW, Bingert JF, Colligan KJ (2004) Development of grain structure during friction stir welding. Scr Mater 51:243–248

    Article  Google Scholar 

  32. Fonda RW, Knipling KE (2011) Texture development in friction stir welds. Sci Tech Weld Join 16(4):288–294

    Article  Google Scholar 

  33. Shen J, Wang F, Suhuddin UFH, Hu S, Li W, Santos JFD (2015) Crystallographic texture in bobbin tool friction stir welded aluminum. Metal Mater Trans A 46A:2809–2813

    Article  Google Scholar 

  34. Fonda R, Reynolds A, Feng CR, Knipling K, Rowenhorst D (2013) Material flow in friction stir welds. Metal Mater Trans A 44A:337–344

    Article  Google Scholar 

  35. Xu WF, Liu JH, Chen DL, Luan GH, Yao JS (2012) Improvements of strength and ductility in aluminium alloy via rapid cooling during friction stir welding. Mater Sci Eng A 548:89–98

    Article  Google Scholar 

  36. Sato YS, Kokawa H, Ikeda K, Enomoto M, Jogan S, Hashimoto T (2001) Microstexture in the friction stir weld of an aluminum allo. Metal Mater Trans A 32A:941–948

    Article  Google Scholar 

  37. Dutta I, Allen SM (1991) A calorimetric study of precipitation in commercial aluminium alloy 6061. J Mater Sci Lett 10:323–326

    Article  Google Scholar 

  38. Woo W, Balogh L, Ungar T, Choo H, Feng Z (2008) Grain structure and dislocation density measurements in a friction-stir welded aluminum alloy using X-ray peak profile analysis. Mater Sci Engg A 498:308–13

    Article  Google Scholar 

  39. Hansen N (2004) Hall-Petch relation and boundary strengthening. Scr Mater 51(8):801–806

    Article  Google Scholar 

  40. Kamikawa N, Huang X, Tsuji N, Hansen N (2009) Strengthening mechanisms in nanostructured high-purity aluminium deformed to high strain and annealed. Act Mater 57:4198–4208

    Article  Google Scholar 

  41. Ma ZY, Mishra RS, Mahoney MW (2002) Superplastic deformation behavior of friction stir processed 7075 Al alloy. Act Mater 50:4419–4430

    Article  Google Scholar 

  42. Charit I, Mishra RS (2003) High strain rate superplasticity in a commercial 2024 Al alloy via friction stir processing. Mater Sci Engg A 359:290–296

    Article  Google Scholar 

  43. Imam M, Biswas K, Racherla V (2013) On use of weld zone temperatures for online monitoring of weld quality in friction stir welding of naturally aged aluminium alloys. Mater Des 52:730–739

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Joining and Welding Research Institute, Osaka University, Ibaraki, 5670047, Japan

    Murshid Imam, Hidetoshi Fujii, Yufeng Sun & Yoshiaki Morisada

  2. Department of Mechanical Engineering, Indian Institute of Technology, Kharagpur, 721302, India

    Vikranth Racherla & Kajal Biswas

  3. Department of Mechanical and Aerospace Engineering, Indian Institute of Technology, Hyderabad, 502205, India

    Viswanath Chintapenta

Authors
  1. Murshid Imam
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Vikranth Racherla
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Kajal Biswas
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Hidetoshi Fujii
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Viswanath Chintapenta
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. Yufeng Sun
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. Yoshiaki Morisada
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Murshid Imam.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Imam, M., Racherla, V., Biswas, K. et al. Microstructure-property relation and evolution in friction stir welding of naturally aged 6063 aluminium alloy. Int J Adv Manuf Technol 91, 1753–1769 (2017). https://doi.org/10.1007/s00170-016-9865-9

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-016-9865-9

Keywords

Search

Navigation