Abstract
Densification is a modification technique usually applied to low-density wood species to improve the mechanical properties of the wood. However, densification impairs the wettability abilities of the wood surface and has a negative effect on some properties of the coated substrate. In this study, various physical properties of non-densified and densified common beech (Fagus sylvatica L.) wood were investigated. The densification caused the changes in wood density, moisture content, chemical properties and colour. With the aim of overcoming the negative influence of densification on the surface properties and coatability of wood, plasma pre-treatment was performed. Although the densification impaired the wettability of the wood surface, treatment with plasma increased the surface free energy of both non-densified and densified wood. The improved hydrophilicity of the wood after plasma pre-treatment was also reflected in the improved interactions with the liquid coating. Scanning electron microscope analysis of the coated wood surfaces showed reduced penetration of the coating in densified structure of wood, which negatively affected the adhesion of the coating films. However, the negative effect of densification on the coating adhesion was successfully mitigated by pre-treating the wood with plasma. In conclusion, it was shown that plasma treatment is a promising surface modification technique to achieve a better interaction between densified wood and waterborne coating.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Adam N (1957) Use of the term ‘Young’s equation’ for contact angles. Nature 180:809–810. https://doi.org/10.1038/180809a0
Åkerholm M, Salmén L (2004) Softening of wood polymers induced by moisture studied by dynamic FTIR spectroscopy. J Appl Polym Sci 94:2032–2040. https://doi.org/10.1002/app.21133
Altgen D, Altgen M, Kyyrö S, Rautkari L, Mai C (2020) Time-dependent wettability changes on plasma–treated surfaces of unmodified and thermally modified European beech wood. Eur J Wood Prod 78:417–420. https://doi.org/10.1007/s00107-020-01505-0
Arruda LM, Del Menezzi CHS (2013) Effect of thermomechanical treatment on physical properties of wood veneers. Int Wood Prod J 4:217–224. https://doi.org/10.4067/S0718-221X2016005000008
Avramidis G, Klarhöfer L, Maus-Friedrichs W, Militz H, Viöl W (2012) Influence of air plasma treatment at atmospheric pressure on wood extractives. Polym Deg Stab 97:469–471. https://doi.org/10.1016/j.polymdegradstab.2011.12.030
Bekhta P, Krystofiak T (2016) The influence of short-term thermomechanical densification on the surface wettability of wood veneers. Maderas-Cienc tecnol 18:79–90
Bekhta P, Proszyk S, Lis B, Krystofiak T (2014a) Gloss of thermally densified alder (Alnus glutinosa Goertn.), beech (Fagus sylvatica L.), birch (Betula verrucosa Ehrh.), and pine (Pinus sylvestris L.) wood veneers. Eur J Wood Prod 72:799–808. https://doi.org/10.1007/s00107-014-0843-3
Bekhta P, Proszyk S, Krystofiak T, Mamonova M, Pinkowski G, Lis B (2014b) Effect of thermomechanical densification on surface roughness of wood veneers. Wood Mater Sci Eng 9:233–245. https://doi.org/10.1080/17480272.2014.923042
Bekhta P, Proszyk S, Krystofiak T, Lis B (2015) Surface wettability of short-term thermo-mechanically densified wood veneers. Eur J Wood Prod 73:415–417. https://doi.org/10.1007/s00107-015-0902-4
Bekhta P, Krystofiak T, Proszyk S, Lis B (2018) Adhesion strength of thermally compressed and varnished wood (TCW) substrate. Prog Org Coat 125:331–338. https://doi.org/10.1016/j.porgcoat.2018.09.013
Belt T, Rautkari L, Laine K, Hill CAS (2013) Cupping behaviour of surface densified Scots pine wood: the effect of process parameters and correlation with density profile characteristics. J Mater Sci 48:6426–6430. https://doi.org/10.1007/s10853-013-7443-1
Brewer CE, Chuang VJ, Masiello CA, Gonnermann H, Gao X, Dugan B, Driver LE, Panzacchi P, Zygourakis K, Davies CA (2014) New approaches to measuring biochar density and porosity. Biomass Bioenerg 66:176–185. https://doi.org/10.1016/j.biombioe.2014.03.059
Chen Y, Tshabalala MA, Gao J, Stark NM, Fan Y (2014) Color and surface chemistry changes of extracted wood flour after heating at 120 C. Wood Sci Technol 48:137–150. https://doi.org/10.1007/s00226-013-0582-3
Darwis A, Wahyudi I, Dwianto W, Cahyono TD (2017) Densified wood anatomical structure and the effect of heat treatment on the recovery of set. J Indian Acad Wood Sci 14:24–31. https://doi.org/10.1007/s13196-017-0184-z
De Meijer M, Militz H (2000) Wet adhesion of low-VOC coatings on wood: A quantitative analysis. Prog Org Coat 38:223–240. https://doi.org/10.1016/S0300-9440(00)00108-9
De Meijer M, Thurich K, Militz H (2001) Quantitative measurements of capillary coating penetration in relation to wood and coating properties. Holz Roh- Werkst 59:35–45. https://doi.org/10.1007/s001070050469
De Moura LF, Hernández RE (2005) Evaluation of varnish coating performance for two surfacing methods on sugar maple wood. Wood Fiber Sci 37:355–366
Dömény J, Čermák P, Koiš V, Tippner J, Rousek R (2018) Density profile and microstructural analysis of densified beech wood (Fagus sylvatica L.) plasticized by microwave treatment. Eur J Wood Prod 76:105–111. https://doi.org/10.1007/s00107-017-1173-z
EN ISO 4624 (2016) Paints and varnishes – —pull-off test for adhesion. Brussels, Belgium, European Committee for Standardization
Fang C-H, Blanchet P, Cloutier A, Barbuta C (2012) Engineering wood flooring with a densified surface layer for heavy-duty use. BioResources 7:5843–5854
Galmiz O, Talviste R, Panáček R, Kováčik D (2019) Cold atmospheric pressure plasma facilitated nano-structuring of thermally modified wood. Wood Sci Technol 53:1339–1352. https://doi.org/10.1007/s00226-019-01128-6
Ganne-Chédeville C, Jääskeläinen A-S, Froidevaux J, Hughes M, Navi P (2012) Natural and artificial ageing of spruce wood as observed by FTIR-ATR and UVRR spectroscopy. Holzforschung 66:163–170. https://doi.org/10.1515/HF.2011.148
Gašparík M, Gaff M (2015) Influence of densification on bending strength of beech wood. Wood research 60:211–218
GeoPyc 1365 Operator Manual (2017) Micromeritics Instrument Corporation, Norcross, GA, USA
Gibbons MJ, Nikafshar S, Saravi T, Ohno K, Chandra S, Nejad M (2020) Analysis of a wide range of commercial exterior wood coatings. Coatings 10:1013. https://doi.org/10.3390/coatings10111013
Gwon JG, Lee SY, Doh GH, Kim JH (2010) Characterization of chemically modified wood fibers using FTIR spectroscopy for biocomposites. J Appl Polym Sci 116:3212–3219. https://doi.org/10.1002/app.31746
Higashihara T, Morooka T, Hirosawa S, Norimoto M (2004) Relationship between changes in chemical components and permanent fixation of compressed wood by steaming or heating. Mokuzai Gakkaishi 50:159–167
ISO 13061-1 (2014) Physical and mechanical properties of wood – Test methods for small clear wood specimens – Part 1: Determination of moisture content for physical and mechanical tests. Geneva, Switzerland, International Organization for Standardization
Jakob M, Gaugeler J, Gindl-Altmutter W (2020) Effects of fiber angle on the tensile properties of partially delignified and densified wood. Materials 13:5405. https://doi.org/10.3390/ma13235405
Jennings JD, Zink-Sharp A, Kamke FA, Frazier CE (2005) Properties of compression densified wood. Part I: bond performance. J Adhes Sci Techn 19:1249–1261. https://doi.org/10.1163/156856105774429055
Jennings JD, Zink-Sharp A, Frazier CE, Kamke FA (2006) Properties of compression-densified wood, Part II: surface energy. J Adhes Sci Technol 20:335–344. https://doi.org/10.1163/156856106776381802
Kadivar M, Gauss C, Ghavami K, Savastano HJ (2020) Densification of bamboo: state of the art. Materials 13:4346. https://doi.org/10.3390/ma13194346
Král P, Ráhel’ J, Stupavská M, Šrajer J, Klímek P, Kumar Mishra P, Wimmer R (2015) XPS depth profile of plasma-activated surface of beech wood (Fagus sylvatica) and its impact on polyvinyl acetate tensile shear bond strength. Wood Sci Technol 49:319–330. https://doi.org/10.1007/s00226-014-0691-7
Kúdela J, Rešetka M, Rademacher P, Dejmal A (2017) Influence of pressing parameters on surface properties of compressed beech wood. Wood Research 62:939–950
Kutnar A, Kamke FA, Sernek M (2008) Themechanical properties of densified VTC wood relevant for structural composites. Holz Roh Werkst 66:439–446. https://doi.org/10.1007/s00107-008-0259-z
Kutnar A, Rautkari L, Laine K, Hughes M (2012) Thermodynamic characteristics of surface densified solid Scots pine wood. Eur J Wood Prod 70:727–734. https://doi.org/10.1007/s00107-012-0609-8
Kutnar A, O’Dell J, Hunt C, Frihart C, Kamke F, Schwarzkopf M (2021) Viscoelastic properties of thermo–hydro–mechanically treated beech (Fagus sylvatica L.) determined using dynamic mechanical analysis. Eur J Wood Prod 79:263–271. https://doi.org/10.1007/s00107-020-01629-3
Laine K, Rautkari L, Hughes M, Kutnar A (2013) Reducing the set-recovery of surface densified solid Scots pine wood by hydrothermal post-treatment. Eur J Wood Prod 71:17–23. https://doi.org/10.1007/s00107-012-0647-2
Laine K, Segerholm K, Wålinder M, Rautkari L, Ormondroyd G, Hughes M, Jones D (2014) Micromorphological studies of surface densified wood. J Mater Sci 49:2027–2034. https://doi.org/10.1007/s10853-013-7890-8
Laskowska A (2017) The influence of process parameters on the density profile and hardness of surface-densified birch wood (Betula pendula Roth). BioResources 12:6011–6023
Lesar B, Humar M, Kamke FA, Kutnar A (2013) Influence of the thermo-hydro-mechanical treatments of wood on the performance against wood-degrading fungi. Wood Sci Technol 47:977–992. https://doi.org/10.1007/s00226-013-0553-8
Liu XY, Timar MC, Varodi AM, Sawyer G (2017) An investigation of accelerated temperature-induced ageing of four wood species: colour and FTIR. Wood Sci Technol 51:357–378. https://doi.org/10.1007/s00226-016-0867-4
Mania P, Wróblewski M, Wójciak A, Roszyk E, Moliński W (2020) Hardness of densified wood in relation to changed chemical composition. Forests 11:506. https://doi.org/10.3390/f11050506
Navi P, Girardet F (2000) Effects of thermo-hydro-mechanical treatment on the structure and properties of wood. Holzforschung 54:287–293. https://doi.org/10.1515/HF.2000.048
Noüy D (1925) An interfacial tensiometer for universal use. J Gen Physiol 7:625–631. https://doi.org/10.1085/jgp.7.5.625
Odrášková M, Ráhel’ J, Zahoranová A, Tiňo R, Černák M (2008) Plasma activation of wood surface by diffuse coplanar surface barrier discharge. Plasma Chem Plasma Process 28:203–211. https://doi.org/10.1007/s11090-007-9117-8
Owens DK, Wendt RC (1969) Estimation of the surface free energy of polymers. J Appl Polym Sci 13:1741–1747. https://doi.org/10.1002/app.1969.070130815
Petrič M, Kutnar A, Rautkari L, Laine K, Hughes M (2013) Influence of surface densification of wood on its dynamic wettability and surface free energy. In: Mittal KL (ed) Advances in contact angle, wettability and adhesion. Scrivener Publishing LLC, Beverly, pp 279–296. https://doi.org/10.1002/9781118795620.ch16
Rana R, Langenfeld-Heyser R, Finkeldey R, Polle A (2010) FTIR spectroscopy, chemical and histochemical characterisation of wood and lignin of five tropical timber wood species of the family of Dipterocarpaceae. Wood Sci Technol 44:225–242. https://doi.org/10.1007/s00226-009-0281-2
Rautkari L, Hughes M, Properzi M, Pichelin F (2010a) Properties and chemical changes of surface densified wood. In: Ceccotti A (ed) Proceedings of the 11th World Conference on timber engineering, 20–24 June 2010, Trentino, Italy
Rautkari L, Kutnar A, Hughes M, Kamke FA (2010b) Wood surface densification using different methods. In: Ceccotti A (ed) Proceedings of the 11th World Conference on timber engineering, 20–24 June 2010, Trentino, Italy
Rautkari L, Laine K, Kutnar A, Medved S, Hughes M (2013) Hardness and density profile of surface densified and thermally modified Scots pine in relation to degree of densification. J Mater Sci 48:2370–2375. https://doi.org/10.1007/s10853-012-7019-5
Reinprecht L, Tiňo R, Šomšák M (2020) The impact of fungicides, plasma, UV-additives and weathering on the adhesion strength of acrylic and alkyd coatings to the Norway spruce wood. Coatings 10:1111. https://doi.org/10.3390/coatings10111111
Schwarze FWMR, Spycher M (2005) Resistance of thermo-hygro-mechanically densified wood to colonisation and degradation by brown-rot fungi. Holzforschung 59:358–363. https://doi.org/10.1515/HF.2005.059
Shi J, Peng J, Huang Q, Cai L, Shi SQ (2020) Fabrication of densified wood via synergy of chemical pretreatment, hot–pressing and post mechanical fixation. J Wood Sci 66:5. https://doi.org/10.1186/s10086-020-1853-x
Skyba O, Schwarze FWMR, Niemz P (2009) Physical and mechanical properties of thermo-hygro-mechanically (THM) – densified wood. Wood research 54:1–18
Thomas M, Mittal KL (2013) Atmospheric pressure plasma treatment of polymers: Relevance to adhesion. Scrivener Publishing LLC, Beverly. https://doi.org/10.1002/9781118747308
Vnučec D, Žigon J, Mikuljan M, Kamke FA, Šernek M, Kutnar A, Goršek A (2017) Bonding of densified beech wood using adhesives based on thermally modified soy proteins. Eur J Wood Prod 75:767–776. https://doi.org/10.1007/s00107-017-1164-0
Wilhelmy L (1863) Ueber die Abhängigkeit der Capillaritäts- Constanten des Alkohols von Substanz und Gestalt des benetzten festen Körpers. Annalen der Phys 195:177–217. https://doi.org/10.1002/andp.18631950602
Yu Y, Li A, Yan K, Ramaswamy HS, Zhu S, Li H (2020) High-pressure densification and hydrophobic coating for enhancing the mechanical properties and dimensional stability of soft poplar wood boards. J Wood Sci 66:45. https://doi.org/10.1186/s10086-020-01892-1
Žigon J, Dahle S (2019) Improvement of plasma treatment efficiency of wood and coating process by sodium chloride aqueous solutions. Proligno 15:260–267
Žigon J, Petrič M, Dahle S (2018) Dielectric barrier discharge (DBD) plasma pretreatment of lignocellulosic materials in air at atmospheric pressure for their improved wettability: a literature review. Holzforschung 72(11):979–991. https://doi.org/10.1515/hf-2017-0207
Žigon J, Petrič M, Dahle S (2019) Artificially aged spruce and beech wood surfaces reactivated using FE-DBD atmospheric plasma. Holzforschung 73:1069–1081. https://doi.org/10.1515/hf-2019-0005
Žigon J, Dahle S, Petrič M, Pavlič M (2020a) Enhanced abrasion resistance of coated particleboard pre-treated with atmospheric plasma. Drv Ind 71:129–137. https://doi.org/10.5552/drvind.2020.1960
Žigon J, Kovač J, Zaplotnik R, Šernek M, Petrič M, Dahle S (2020b) Enhancement of strength of adhesive bond between wood and metal using atmospheric plasma treatment. Cellulose 27:6411–6424. https://doi.org/10.1007/s10570-020-03212-8
Žigon J, Pavlič M, Kibleur P, Van den Bulcke J, Petrič M, Van Acker J, Dahle S (2020c) Treatment of wood with atmospheric plasma discharge: study of the treatment process, dynamic wettability and interactions with a waterborne coating. Holzforschung. https://doi.org/10.1515/hf-2020-0182 (ahead of print)
Acknowledgements
The author acknowledges the financial support of the Slovenian Research Agency (research core funding No. P4-0015, "Wood and lignocellulosic composites") and the help of Mr. Samo Grbec for his help by the measurements of wood envelope density.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The corresponding author states that there is no conflict of interest.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Žigon, J. Interactions of a waterborne coating with plasma pre-treated densified beech wood. Eur. J. Wood Prod. 79, 1383–1394 (2021). https://doi.org/10.1007/s00107-021-01716-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00107-021-01716-z