Abstract
The latent heat thermal energy storage (LHTES) by phase change material (PCM) is more promising than supplementary technologies due to elevated heat capacity per unit volume and small volume change during heat exchange. The efficiency of the LHTES system mainly determines upon the thermophysical properties of PCM, operating conditions, and geometric parameters of a heat exchanger or PCM container. Geometric parameters like shape, size, height, type, and orientation of heat exchanger have greatly influenced the heat convey rate in between heat convey fluid and PCM. The tube and shell-type heat exchangers are most widely studied and analyzed by the researchers. This review presents and summarizes the different types of PCM container/heat exchanger which are used in the case of PCM along with geometric heat transfer enhancement techniques like fins, heat pipes, and multiple tubes, etc. The main focus is on the melting behavior of PCM interior the containers/heat exchangers which is an important variable to magnify the thermal charging capabilities of the LHTES system.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Sattari H, Mohebbi A et al (2017) CFD simulation of melting process of phase change materials (PCMs) in a spherical capsule. Int J Refrig 73:209–218
Kalapala L, Devanuri J (2019) Parametric investigation to assess the melt fraction and melting time for a latent heat storage material based vertical shell and tube heat exchanger. Sol Energy 193:360–371
Karami R, Kamkari B (2020) Experimental investigation of the effect of perforated fins on thermal performance enhancement of vertical shell and tube latent heat energy storage systems. Energy Convers Manage 210:112679
Tan F (2008) Constrained and unconstrained melting inside a sphere. Int Commun Heat Mass Transfer 35:466–475
Li W, Li S et al (2017) Numerical study on melt fraction during melting of phase change material inside a sphere. Int J Hydrogen Energy 42:18232–18239
Kamkari B, Shokouhmand H (2014) Experimental investigation of the effect of inclination angle on convection-driven melting of phase change material in a rectangular enclosure. Int J Heat Mass Transf 72:186–200
Kamkari B, Shokouhmand H (2014) Experimental investigation of phase change material melting in rectangular enclosures with horizontal partial fins. Int J Heat Mass Transf 78:839–851
Haddad Z, Iachachene F (2019) Melting characteristics of organic phase change material in a wavy trapezoidal cavity. J Mol Liquids, 112132
Seddegh S, Wang X et al (2016) A comparative study of thermal behaviour of a horizontal and vertical shell-and-tube energy storage using phase change materials. Appl Therm Eng 93:348–358
Mahdi M, Mahood H et al (2019) Numerical study on the effect of the location of the phase change material in a concentric double pipe latent heat thermal energy storage unit. Thermal Sci Eng Progr 11:40–49
Bechiri M, Mansouri K et al (2019) Study of heat and fluid flow during melting of PCM inside vertical cylindrical tube. Int J Therm Sci 135:235–246
Saraswat A, Bhattacharjee R et al (2017) Investigation of diffusional transport of heat and its enhancement. Appl Therm Eng 111:1611–1621
Joybari M, Seddegh S et al (2019) Experimental investigation of multiple tube heat transfer enhancement in a vertical cylindrical latent heat thermal energy storage system. Renew Energy 140:234–244
Hosseini M, Rahimi M et al (2014) Experimental and computational evolution of a shell and tube heat exchanger as a PCM thermal storage system. Int Commun Heat Mass Transfer 50:128–136
Sodhi G, Jaiswal A et al (2019) Investigation of charging and discharging characteristics of a horizontal conical shell and tube latent thermal energy storage device. Energy Convers Manage 188:381–397
Al I, Khanna S et al (2019) An experimental and numerical study on the effect of inclination angle of phase change materials thermal energy storage system. J Energy Storage 23:57–68
Mahdi Mustafa S, Mahood Hameed B et al (2019) Experimental study on the melting behavior of a phase change material in a conical coil latent heat thermal energy storage unit. Appl Therm Eng 11:40–49
Mao Q, Liu N et al (2019) A novel shell-and-tube thermal energy storage tank: Modeling and investigations of thermal performance. Appl Therm Eng 159:113964
Seddegh S, Cao F et al (2017) Comparison of heat transfer between cylindrical and conical vertical shell-and-tube LHTES systems. Appl Therm Eng
Mahdi M, Mahdi J et al (2020) Improved PCM melting in a thermal energy storage system of double-pipe helical-coil tube. Energy Convers Manage 203:112238
Yang X, Lu Z et al (2017) Thermal performance of a shell-and-tube latent heat thermal energy storage unit: Role of annular fins. Appl Energy 202:558–570
Mahood H, Mahdi M et al (2020) Numerical investigation on the effect of fin design on the melting of phase change material in a horizontal shell and tube thermal energy storage. J Energy Storage 29:101331
Bhagat K, Prabhakar M et al (2018) Estimation of thermal performance and design optimization of finned multitube latent heat thermal energy storage. J Energy Storage 19:135–144
Nie C, Deng S et al (2020) Numerical investigation of PCM in a TES unit with fins: consecutive charging and discharging. J Energy Storage 29:101319
Reay D, Kew P et al (2013) Heat pipes: theory, design and applications. Butterworth Heinemann
Mahdavi M, Tiari S et al (2020) A numerical study on the combined effect of dispersed nanoparticles and embedded heat pipes on melting and solidification of a shell and tube latent heat thermal energy storage system. J Energy Storage 27:101086
Motahar S, Khodabandeh R et al (2016) Experimental study on the melting and solidification of a phase change material enhanced by heat pipe. Int Commun Heat Mass Transfer 73:1–6
Sharifi N, Wang S et al (2012) Heat pipe-assisted melting of a phase change material. Int J Heat Mass Transf 55:3458–3469
Fadl M, Eames P (2019) A comparative study of the effect of varying wall heat flux on melting characteristics of phase change material RT44HC in rectangular test cells. Int J Heat Mass Transf 141:731–747
Zivkovic B, Fujii I (2001) Analysis of isothermal phase change of phase change material within rectangular and cylindrical containers. Sol Energy 70:51–61
Vyshak N, Jilani G (2007) Numerical analysis of latent heat thermal energy storage system. Energy Convers Manage 48:2161–2168
Seddegh S, Wang X (2017) Investigation of the effect of geometric and operating parameters on thermal behavior of vertical shell-and-tube latent heat energy storage systems. Energy 137:69–82
Esapour M, Hosseini M (2016) Numerical study on geometrical specifications and operational parameters of multi-tube heat storage systems. Appl Therm Eng 109:351–363
Zayed M, Zhao J et al (2020) Recent progress in phase change materials storage containers: geometries, design considerations and heat transfer improvement methods. J Energy Storage 30:101341
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2022 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this paper
Cite this paper
Kumar, J., Singh, P., Kumar, R. (2022). The Effect of Geometric Parameters of a Container on Thermal Charging of Latent Heat Thermal Energy Storage System: A Review. In: Govindan, K., Kumar, H., Yadav, S. (eds) Advances in Mechanical and Materials Technology . EMSME 2020. Lecture Notes in Mechanical Engineering. Springer, Singapore. https://doi.org/10.1007/978-981-16-2794-1_103
Download citation
DOI: https://doi.org/10.1007/978-981-16-2794-1_103
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-16-2793-4
Online ISBN: 978-981-16-2794-1
eBook Packages: EngineeringEngineering (R0)