Keywords

Introduction

The construction and operation of railways implies changes in the surrounded landscape that alter the microclimate, soil, and hydrological dynamics, contributing to the degradation of the natural habitat for many species (Forman and Alexander 1998; Eigenbrod et al. 2009). During operation, the main disturbances caused by railways are air, soil and water pollution, as well as noise and vibration, which may alter species richness and species abundance (e.g. Penone et al. 2012; Clauzel et al. 2013). In this chapter, we review these disturbance sources, their effects on wildlife and the main actions to avoid or minimize their effects.

Main Railway Disturbances: Noise and Vibration, and Air, Soil and Water Pollution

The two most known disturbances of railways are the noise and vibrations caused by passing trains. However, railways are also responsible for a large amount of emissions that cover a wide range of pollutants and toxic substances that affect the atmosphere, soil and water worldwide (Plakhotnik et al. 2005). Another impact resulting from the construction and establishment of the railways is soil erosion. Here, we describe the main railway disturbances that can potentially affect wildlife.

Noise and Vibration

Railway noise pollution can be either from airborne sound or from vibration-induced as a result of rail traffic (Czop and Mendrok 2011; Palacin et al. 2014). The main source of railway noise comes from freight wagons, followed by high-speed trains and inner-urban railways (Guarinoni et al. 2012). However, locomotives passing and accelerating, freight wagons braking, vibrations from rail corrugation, and out-of-round wheels or vehicle coupling in shunting yards, are other sources of noise (Clausen et al. 2010). Noise levels vary, depending on the landscape and weather; open and flat areas allow noise to travel further than forest or mountains areas. In mountainou areas, the effect of noise is greater within valleys, when their width is less than the height of their walls, reducing the attenuating effect of noise (Chiocchia et al. 2010). Frost can make the ground hard and impede sound absorption, but fog prevents noise from dissipating.

Noise above 55 dB(A), where dB(A) is a measure that attempts to correct the way the human ear perceives loudness, is considered noise pollution for humans, and the sound values in the range 65–75 dB(A) cause stress to the body, leading to arterial hypertension (high blood pressure), cardiovascular disease, and heart attacks (Berglund et al. 1999). In Canada, the sound level of a passing train reaches values up to 85 dB(A), but between trains the sound levels drop to 43–53 dB(A) (CTA 2015). Measurement campaigns on high speed trains in several European countries over 10 years revealed sound values ranging from 85.5 to 97 dB(A) when the train speed was between 250 and 350 km/h (Gautier et al. 2008). In Japan, Matsumoto et al. (2005) compared the noise as a function of distance and observed a high noise level of 64 dB at 200 m from a railway in the countryside, a value similar to that near residential areas (65.7 dB). In fact, in Japan, noise can still reach 72 dB at 50 m from the track, i.e., higher than the Japanese permissible standards of 70 dB(A) (Kanda et al. 2007).

Air Pollution and Emission

The emission of gases from traffic constitutes an important source of environmental pollution all over the world (Hofman et al. 2014). These emissions depend mainly on the type of transport and fuel. Potential sources of contaminants associated with railways include diesel exhaust, and the abrasion of brakes, wheels, and rails, as well as dust from the transport of minerals and treated railway ties (Levengood et al. 2015).

The main pollutants emitted from the diesel-powered locomotives are carbon dioxide (CO2), methane (CH4), carbon monoxide (CO), nitrogen oxides (NOx), nitrous oxide (N2O), sulphur dioxide (SO2), non-methane volatile organic compounds (NMVOC), particulate matter (PM) and hydrocarbon (HC) (Plakhotnik et al. 2005; Cheng and Yan 2011). Some studies reported higher levels of PM10 (where the subscript indicates the largest diameter of the particles in microns) and PM2.5 near railways, higher than the standard level allowed (Beychok 2011) for the USA, Europe, and Asia (Park and Ha 2008; Kamani et al. 2014).

A growing number of monitoring studies have used bioindicator plant species as surrogates of air pollution across railways (e.g., Rani et al. 2006; Hofman et al. 2014). For example, Rani et al. (2006) studied the micromorphology of leaf parts of Croton bonplandianum, Cannabis sativa and Calotropis procera along a gradient of distances from the railway and concluded that the number of stomata and epidermal cells were lower near railways than at 4 kilometers away from the railway. However, no statistical tests were used to evaluate the correlation between railway distance and the number of stomata and epidermal cells. To the best of our knowledge, Rybak and Olejniczak (2013) authored the only published study that measured the accumulation of polycyclic aromatic hydrocarbons (PAH) in animal species. Using Agelenids spider webs to collect dust suspended in the air, they concluded that spiders are efficient indicators of PAHs in roads, but not in railway viaducts due to heavier traffic in the former.

Soil Pollution

With the increase in the human population and vehicles, emissions arising from transportation have become one of the most important sources of heavy metal, PAHs and herbicides in the soil (Malawaka and Wilkomirski 2001; Böjersson et al. 2004). Fuel combustion, vehicular and track material abrasion, and leaked cargo emit particles containing metals that are deposited in the soils, where they can remain for many years due to their low biodegradability (Zhang et al. 2012).

As most products of vehicle emissions are neither biologically nor chemically degraded, they can affect the growth of plants and ecosystems (Chen et al. 2014a, b). In fact, plants and soil organisms are the first recipients of the emission pollutants (Malawaka and Wilkomirski 2001). Ongoing research indicates that plant uptake varies among species. For example, leucaena (Leucaena leucocephala), annual meadow grass (Poa annua), and indigofera (Indigofera amblyantha) are known to have high translocation capacity for some metals, such as lead (Pb) and cadmium (Cd), but limited translocation of heavy metals from the roots to the aboveground tissues (Chen et al. 2014a, b), while others show the opposite trend (Ge et al. 2003).

High concentration levels of heavy metals are often found in the vicinity of railways. Wiłkomirski et al. (2011) reported the same concentration of molybdenum (Mo) close to and approximately 2 km from the railways in Poland. For instance, the concentration of nickel, cadmium, cobalt, and lead in the moss (Pleurozium schreberi) was the same 30 m from the railway as it was at points near the railways (Mazur et al. 2013). In addition, high concentrations of PAHs were found in the aerial parts of plant species near the railway and up to distances of 30 m from the railway (Malawaka and Wilkomirski 2001; Wiłkomirski et al. 2011). On railways, in particular, the biodegradation of PAHs and herbicides is extremely low and can persist over decades (Wilkomirski et al. 2012).

Water Pollution

Infrastructures associated with railways (e.g., leakages of petroleum products from fuel storage tanks) contribute, together with pollutants, to aquatic ecosystems (Schweinsberg et al. 1999; Vo et al. 2015). Levengood et al. (2015) documented high concentrations of PAHs and heavy metals in waterways bisected or bordered by railways. They showed that the PAH concentration was higher downstream than upstream of the railway (Levengood et al. 2015). They also found that phenanthrene and dibenzo (a, h) anthracene (a PAH element) concentrations at some sites represented a risk to aquatic life, whereas the chromium (Cr) values were still below the levels of concern for aquatic life (Levengood et al. 2015).

Herbicides and pesticides are other sources of water pollution. For herbicides, Schweinsberg et al. (1999) discovered that in Germany before the 1990s, a much higher total amount of these compounds were applied on railway tracks than in agriculture. Recently, Vo et al. (2015) showed that many herbicides applied during the operation of the railway are at concentrations that are lethal to most of the aquatic fauna, particularly fish populations; they indicate that compounds such as Imazapyr or Diuron concentrations can take 6 and 48 months, respectively, to drop below 50% of their original levels.

Soil Erosion and Changes in Hydrology

The abrupt change of soil required to establish the railway embankment leads to vegetation loss, compresses the soil, and compromises water drainage (Ferrell and Lautala 2010). Thus, soil becomes exposed and subject to an increasing runoff that promotes its erosion (Chen et al. 2015). The erosion of rail embankments can result in a washing out of sediments (Jin et al. 2008) that cause water pollution. Furthermore, Gregorich et al. (1998) noted that soil erosion and deposition alter the biological process of carbon mineralization in soil landscapes, which affects the soil quality and, hence, the vegetation.

Railway construction parallel to streams can result in hydrological disconnections (Pennington et al. 2010) that dry the soils (Blanton and Marcus 2009). Such disconnections can have a significant impact on the ecological function of riparian landscapes by negatively affecting floodplain evolution, riparian ecosystem processes, and associated biodiversity (Snyder et al. 2002). Although urban riparian areas could harbor great diversity of native canopy and shrub species, the richness of native canopy species was lower near railways (Snyder et al. 2002).

Effects of Railway Disturbance on Wildlife

There is evidence that disturbance from noise, lights, and vibrations associated with the construction and operation of the railway affect some species, and this can occur at various life cycles (van Rooyen 2009; Wiacek et al. 2015). In contrast, other studies suggest that wildlife ignores or adapts to railway disturbances (Ghosh et al. 2010; Mundahl et al. 2013). As observed for roads, the severity of railway disturbance depends on the species’ bio-ecological features and on the degree of the disturbance (e.g., Rytwinski and Fahrig 2012). However, little is known about their role in species viability. We now review the main findings on wildlife behaviour responses to railway disturbance.

Insects

To the best of our knowledge, only the study by Penone et al. (2012) assessed the impact of railways on insects. They studied Tettigoniidae (bush crickets) at railway edges in an urban context (Penone et al. 2012), and found that species richness and abundance was explained by a quadratic effect of train speed (described by a humpbacked curve). This is especially true of mobile species at larger scales than on sedentary species. However, vegetated railway verges had a significant positive effect on most species, suggesting that suitable habitats with appropriate management can overcome the negative effects of disturbance on larger scales (Penone et al. 2012).

Herpetofauna

Among vertebrates, amphibians are one of the groups most affected by linear infrastructures (e.g., Fahrig and Rytwinski 2009). Their dependence on aquatic habitats and seasonal migrations make amphibians particularly vulnerable to the negative impacts of these structures (Hels and Buchwald 2001; Hamer and McDonnell 2008). However, to the best of our knowledge no studies have been carried out on the impact of railway disturbances on amphibians.

In contrast, there have been several studies that show that reptiles ignore railway disturbances. For example, in Belgium, all autochthonous reptile species have colonized the railway embankments, but their presence and abundance largely depend on the region and on the kind of railway (Graitson 2006). Railway embankments can provide important novel habitats for reptiles, mainly in highly human-altered landscapes (EN 2004). Some active lines in sunny areas of large valleys and some large switchyards, as well as unused railways not dismounted, had a particularly high richness of reptiles (Graitson 2006). In fact, those railways may have contributed to the local dispersal of at least five species of reptiles: slow worm (Anguis fragilis), sand lizard (Lacerta agilis), common wall lizards (Podarcis muralis), viviparous lizard (Zootoca vivipara), and smooth snake (Coronella austriaca) (Graitson 2006). Likewise, the rainbow lizard (Cnemidophorus lemnistactus) was found in the weeds growing along the Florida East Coast Railway line occupied by industrial buildings (Wilson and Porras 1983). In Switzerland, a relatively great abundance of reptile species can be found in the vicinity of the railways, especially sand lizards (Stoll 2013). However, the abundance of reptiles in the railway banks can be affected by two key factors: the inter-specific competition with the common wall lizard Podarcis muralis, and predation through domestic cats Felis catus (Stoll 2013).

Birds

There have been several studies that show that railway disturbance affects bird richness, abundance, and behaviour. Noise can affect acoustic communication among bird species that use calls and songs to attract and bond with mates, defend territories from rivals, maintain contact with social groups, beg for food, and warn of danger from approaching predators (Collins 2004; Marler 2004). Noise disturbance was shown to alter the behaviour of many bird species, especially for breeding birds, when territories are being defended, and during incubation (Reijnen et al. 1995). This disturbance can cause birds to accelerate hatching, abandon their occupied territories, nests and broods, and lead to hearing loss (Hanson 2007).

For example, noise emission from railway traffic has a negative effect on the density of all meadow birds in the Netherlands (Waterman et al. 2002). The threshold noise level from which densities were affected was around 42–49 dB(A) for the black-tailed godwit (Limosa limosa), skylark (Alauda arvensis), and garganey (Anas querquedula) (Waterman et al. 2002). There was also evidence that successful bald eagle (Haliaeetus leucocephalus) nests were farther away from highways and railways than unsuccessful ones (Mundahl et al. 2013).

Certain bird species seem to ignore railway disturbances. For example, brants (Branta asp.) seem to disregard the trains passing 50 m away (Owens 1977). Likewise, although Waterman et al. (2002) found a negative effect on the density of birds on railways in general, they did not find differences in bird density between quiet and busy railways. Indeed, there is evidence that bird species tolerate the railway disturbance due to the attractiveness of numerous railway-related features. Species whose predators show negative responses to train disturbance may also benefit from the railway vicinity (Rytwinski and Fahrig 2012). Railway verges may create edge effects that can increase biodiversity. In fact, special microclimates—thanks to different temperatures or insolation and new habitat availability along the edges—can enhance habitat heterogeneity in homogeneous landscapes (Delgado et al. 2007). In turn, these new habitats may improve resting and foraging opportunities for some bird species (Morelli et al. 2014). Also, railways can be a useful source for gastroliths’ digestive purposes, and a source of sand bathing locations used by birds to clean the feathers. Ghosh et al. (2010) showed that apparently due to the food availability, house sparrows (Passer domesticus) adapted to loud noise (between 35 and 95 dB), being undisturbed by passing trains at the railway station study site. Equally, Li et al. (2010) observed the abundance and richness of seven ground-dwelling bird species, namely the Tibetan ground tit (Pseudopodoces humilis), Tibetan lark (Melanocorypha maxima), horned lark (Eremophila alpestris), white-winged snowfinch (Montifringillla nivalis), plain-backed snowfinch (M. blandfordi), white-rumped snowfinch (M. taczanowskii), and rufous-necked snowfinch (M. ruficollis). They found greater numbers of individuals of these species near the Qinghai-Tibet railway (less than 300 m) than farther away (from 300 to 1,200 m), probably due to verges provide nesting sites and foraging opportunities.

The non-continuous nature of the noise near railways due to the intermittent flow of train traffic may constitute the main reason that some birds ignore the railway. This was hypothesized by Wiacek et al. (2015) to explain the greater abundance of the breeding community of woodland birds near a busy railway line in Poland when they assessed the effect of noise at three different distances from the track (30, 280, and 530 m). Species with low frequency calls, such as the wood pigeon (Columba palumbus) and common cuckoo (Cuculus canorus), also occurred in large numbers near railways. Other bird species also seem to ignore the railway disturbance. For example, more than 90% of bald eagle nests were built near human infrastructures, including railways that had more than 1,000 railcars going by each day (Mundahl et al. 2013).

Mammals

Railway disturbance impacts differ among mammal species. Besides the higher intensity of light and noise (it can achieve 120 dB), small mammals can be found near the railways if there is no grazing disturbance (Qian et al. 2009), or if the unnatural nature of rail bed and tracks is not an obstacle to their movements (van der Grift 1999). In fact, the richness of small mammal species was high at the railway verge in the Atlantic forest in southern Brazil (Cerboncini 2012), probably because the noise from the trains can force predators out of the area, which can favor small mammals’ appearance (Cerboncini 2012). Similarly, railways may have a positive role in maintaining the common bat populations in highly humanized landscapes, such as intensive agriculture. In this case, railway verges seem to be used as shelters for bat species despite the traffic noise; only Myotis sp. foraging behaviour was negatively affected by railway verges (Vandevelde et al. 2014).

Although the response of large mammals to the effects of railway disturbance varies among species, they seem to ignore railway disturbances. However, there is evidence that the presence of railways had a subtle effect on some species’ behaviour. For example, railways had little effect on the distance or direction of fox dispersal movements (Trewhella and Harris 1990); however, the railway disturbance may have influenced the fox movements within their territories (Trewhella and Harris 1990). Similarly, the Canadian Pacific Railway in Banff National Park seems to redirect wolf movements (individuals follow the railway), particularly when the snow is deep (Paquet and Callaghan 1996), while it seems to define the boundary of bears’ home ranges (Kaczensky et al. 2003). As detected for other species groups, changes in the railway verges can attract large mammals. In Banff National Park, railway verges attracted black and grizzly bears (Ursus americanus and U. arctos, respectively) due to the berry-producing areas within the verges (Gibeau and Herrero 1998). Grain spills along the Canadian Pacific rail line also attract bears (Gibeau and Herrero 1998), while food spills seem to increase the abundance of mice, which may attract their predators, such as the coyote (Wells 1996).

By contrast, railways seem to be avoided by two large ungulates: Mongolian gazelles (Procopra gutturosa) and Tibetan antelopes (Pantholops hodgsoni). No observations of Mongolian gazelle crossings during dispersal were detected, and most of the individuals were found 300 m from the railway (Ito et al. 2005). Likewise, there were no Tibetan antelope crossings (Xia et al. 2007) because these antelopes hesitated to cross the railway, most likely because of the slope of the rail bed.

Mitigation Measures to Reduce Railway Disturbances

There are several measures to reduce the main negative effects of railway disturbances (Schulte-Werning et al. 2008; Maeda et al. 2012; Nielsen et al. 2015). Although some of these measures are known to effectively reduce the major negative effects on biodiversity, the effectiveness has not yet been evaluated for a few other measures. Here, we describe the commonly used measures to reduce or minimize the impacts of railway disturbance for noise and vibration effects, and soil pollution and erosion that are found in the literature.

Noise and Vibration

In general, there are two approaches to minimizing rail traffic noise and vibration: (1) reduce the noise at the source, and (2) reduce its propagation (Lakušić and Ahac 2012; Tiwari et al. 2013). The reduction of noise levels can be achieved by decreasing the speed of rail vehicles and reducing the intensity of the radiated sound through regular maintenance in order to keep smooth rails and wheels (Lakušić and Ahac 2012; Schulte-Werning et al. 2012). Currently, rail fastenings, rail dampers, under-sleeper pads, and noise barriers (Fig. 6.1) are the most commonly used techniques to directly reduce the noise and vibration in railways, techniques that are also used in roads and motorways. The increased flexibility of railway elements (e.g., fastenings, sleepers, ballasts), have increased their ability to absorb vibrations generated at wheel-rail interface (Lakušić and Ahac 2012). The use of resilient rail fastening systems are designed to decrease the low-frequency ground borne or in structures with noise above 30 Hz and can be effective in reducing wayside noise radiated from steel. This structure provides noise reduction from 3 to 6 dB(A) through the elastic elements supporting the rail, which prevents direct contact between the rail foot and sleeper (Nelson 1997). However, systems that use concrete ties with spring clips may not benefit from the use of resilient fasteners, because the spring clips already eliminate any looseness between the rail and the tie (Nelson 1997).

Fig. 6.1
figure 1

Schematic drawing of a railway showing some measures to minimize noise and vibration: rail fastenings; rail dampers; under-sleepers pads; and noise barriers (not at scale)

Full size image

Another technique is the use of rail dampers (Fig. 6.1). This structure consists of steel components and elastomeric material that absorbs the energy of rail (springs) vibrations (Lakušić and Ahac 2012). The damping material reduces the displacement of the vibration waves along the rail, which results in the reduction of the rail noise. Dampers are known to be an efficient way to reduce noise emission in railway networks (Lakušić and Ahac 2012). Studies performed at the rail track sections with rail dampers installed showed a reduction in noise from 4 to 6 dB(A), and vibration up to 9 dB (Benton 2006; Koller et al. 2012).

Aside from rail noise, non-audible vibrations are also generated by the trains, transmitted via the tracks, and transferred to the soil. In surface railway lines, sleepers with elastic supports (under-sleeper pads—USPs) (Fig. 6.1) are an alternative with moderate costs (compared to floating slab track systems and ballast mats) that increase track quality and achieve a significant reduction in vibrations and railway noise (Schulte-Werning et al. 2012). USPs are resilient pads attached to the bottom surface of sleepers to provide an intermediate elastic layer between the sleeper and the ballast. The USPs are normally made of polyurethane elastomer with a foam structure that includes encapsulated air voids (Johansson et al. 2008). The use of USPs causes an average reduction of vibration of 16 dB due to the reduction of the contact between the sleeper and the ballast, which increases elasticity of the track (Lakušic et al. 2010; Lakušić and Ahac 2012).

Commonly used to isolate the noise on railways (and roads), noise barriers (Fig. 6.1) can be an important tool for minimizing the negative effects of sound on wildlife, especially for species that are extremely sensitive to it. These structures can be constructed from soil, wood, concrete, or metal (FHWA 2011; Morgan and Peeling 2012), or can be just the dense vegetation along the rails, which can, in some cases, form an almost perfect noise barrier (Tiwari et al. 2013; Bashir et al. 2015). Soil verges along roads and railways can reduce, on average, 3 dB more than vertical walls of the same height. However, the construction of soil verges can require a huge area, especially if they are very extensive and elevated. The construction of artificial walls requires less space, but they are usually limited to eight meters in height for structural and aesthetic reasons (FHWA 2011). Vertical walls can be applied, together with soil verges, in order to further reduce noise.

Studies by Van Renterghem and Botteldooren (2012) show that a soil verge can reduce, on average, noise levels of 11.1 dB, and walls can reduce, on average 7.7–8.3 dB. According to the U.S. Department of Transportation, effective noise barriers can typically reduce noise levels by 5–10 dB (FHWA 2011). Noise barriers have been mainly used to reduce the effect of noise on colonies of nesting birds (Bank et al. 2002). However, when applied without planning, noise barriers can cause various negative impacts on wildlife, such as the isolation of populations (Bank et al. 2002). Thus, it is recommended to apply noise barriers together with wildlife passages to promote crossings between railway sides in order to maintain dispersal processes and ensure the long-term persistence of the species (Bank et al. 2002; Schulte-Werning et al. 2012). However, reducing the noise disturbance may reduce the ability of wildlife to perceive incoming trains, and consequently increase the risk of collision (see Chap. 2).

Soil Pollution

Cleaning the ballast using ethylenediaminetetraacetate (EDTA) with water or thermosetting plastic resin are techniques that allow the recycling of pollutant components in the surroundings of the railway network. Cleaning it can typically involve the use of products such as solvents or surfactants, which vary in efficiency and potential environmental impacts (Anderson et al. 2002). The ballast cleaning technology with aqueous solutions of disodium EDTA can ensure metal extraction without altering the stones’ mechanical and physical characteristics, allowing reuse of the ballast (Di Palma and Petrucci 2015). The use of EDTA offers a high extraction efficiency of heavy metals (Di Palma et al. 2011); however, this chemical agent should be administered with caution because it has low biodegradability in the environment (Bucheli-Witschel and Egli 2001).

Using water to extract the ballast pollutants is very common in many countries (Di Palma et al. 2012). However, this method requires a great amount of surfactant water, and the disposal of the waste produced after cleaning must be treated appropriately (Cho et al. 2008). Incineration, landfilling, or recycling of the waste are the options available, with the choice depending on the solvent system and on the nature of the waste (Anderson et al. 2002). Dry cleaning that uses thermosetting plastic resin can successfully remove ballast pollutants in a very short time (Cho et al. 2008). In areas with high levels of contamination, the support material should be renovated regularly, including changing the ballast, and wood sleepers should be replaced by concrete (Wiłkomirski et al. 2011).

Soil Erosion

There are techniques commonly used to minimize the effects of soil erosion on railways and highways: grass plantation, use of gypsum, application of compost/mulch coverage, use of concrete prefabricated panes, lattice plots, and interception and drainage. There is evidence that as the grass cover level increases, the soil erosion rate decreases (Gyasi-Agyei et al. 2001). For example, buffel grass (Cenchrus ciliaris) is one of the preferred species for revegetation of railway embankments in Australia (Bhattarai et al. 2008); in some of the areas (Central Australia and Western Queensland), this grass spreads readily in soils with crumbly or soft surfaces, but it needs to be handled with care because it has the potential to become a weed (Cameron 2004). This species, in combination with Japanese millet (Echinochloa esculenta), has also been used successfully in controlling soil erosion in the semi-arid tropics of Central Queensland. Japanese millet develop rapidly in poor soils and can minimize the invasion of other unwanted weed species (Fox et al. 2010). However, buffel grass is an invasive weed species that poses serious threats to biodiversity in many other environments, such as in the Australian regions mentioned above (Marshall et al. 2012) (see Chap. 4).

The use of gypsum on calcium-deficient soil before seeding can reduce the erosion rate by 25% (Gyasi-Agyei et al. 2001). This material has advantages, such as low cost, availability, pH neutrality, and ease of handling (Gyasi-Agyei et al. 2001). Once applied to the soil, the gypsum will increase the porosity and water infiltration ability. This phenomenon will avoid water runoff, thus preventing soil erosion (Beckett et al. 1989). The use of this mineral also promotes root penetration and the emergence of seedlings (Chen and Dick 2011).

Compost/mulch coverage is considered to be one of the best management practices in both active construction and established areas prone to soil erosion on roadsides (Bakr et al. 2012), and it can be used in railway verges as well. In Louisiana, USA, Bakr et al. (2012) found that compost/mulch covers were highly effective in reducing runoff, total suspended solids (reduction between 70 and 74%), and turbidity from soils susceptible to high-intensity storms. A study performed by Persyn et al. (2004) showed that the use of various compounds applied to the soil might also reduce erosion rates. All compost treatments (biosolids, yard waste, and bio-industrial by-products) were effective at reducing runoff and inter-rill erosion rates under the conditions simulated in the study conducted on a highway embankment after construction in central Iowa (Persyn et al. 2004).

There are also engineering measures, such as concrete prefabricated panes, geocells (three-dimensional honeycomb-like structures to reduce runoff and sediment transport), or interception and drainage that can also reduce the soil loss along highways and railways (e.g., Xu et al. 2006). These measures were effective in the short term by decreasing between 40 and 60% of the runoff that had effectively reduced soil loss from sideslopes of highways in the Tibetan Plateau (Xu et al. 2006). However, this measure needs to be applied with some caution, since weak construction may lead to water leaking from improperly sealed cracks or holes, loose contact parts, poorly rammed structures, or runoff converging along a flow line, causing adverse effects on the road embankment and in the surrounding environment (Xu et al. 2006).

Conclusions

There have been several studies that quantified the level of various disturbances and their impacts on wildlife populations. Plants are, in general, the first to be described in relation to air and soil contamination, perhaps due to the facility of realizing experimental analysis, or of using plants as bio-indicators. Nevertheless, there is still little scant knowledge about the mechanisms and processes underlying the behaviour of vertebrates, because most studies concerned only a small number of species (van der Grift 1999). There is strong evidence that noise, light, and vibrations that can reach from 85.5 to 97 dB(A), can affect insects, amphibians and birds (Fig. 6.2). In contrast, the availability of food and vegetation in the railway verges seems to overcome the noise pollution and seems to attract reptiles, some bird species, and several mammals (Fig. 6.2). There is a wide diversity of measures to minimize railway disturbances, but further studies are needed to understand the effectiveness of these measures in reducing railway disturbance of wildlife.

Fig. 6.2
figure 2

Spatial responses of wildlife to railway disturbances: the length of the white bars are proportional to the distances up to which the railway has an effect on a given taxon, while short and black bars correspond to species’ occurrence in the railway verges

Full size image