Abstract
The research discovers ensuring technological and dynamic capabilities of fine boring due to the use of cantilever boring bars with increased bending stiffness. Experimental design of the cantilever boring bar and a method for increasing its bending stiffness for fine boring of long holes of small diameter (d = 10–20 mm) with a ratio of l/d > 4 is proposed. Bending stiffness increases due to preliminary compression of the outer layers of the boring bar hollow housing with a unique lock pin-drawbar. The experiments were carried out first on pipes of different lengths, in which the effect of the drawbar increased bending stiffness significantly, and then the experiments were carried out on small diameter boring bars. The results of all experiments show a significant increase in bending stiffness and vibration resistance of unique small diameter boring bars for boring long holes. To study the bending vibrations, a testing bench was assembled based on a finishing boring machine. The measurements were carried out using strain-gauge transducers power on via the differential circuit. It has been established that the effect of boring bar drawbar leads to an increase in bending stiffness by about 1.3–1.4 times, and the vibration amplitudes during cutting decrease by about 2–3 times.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Suslov, A.G., Dalsky, A.G.: Scientific Foundations of Engineering Technology. Machine Building, Moscow (2002)
Jablonski, W.: Simulation of cutting process – modeling and applications, engineering the future. INTech (2010)
Usov, A., Oborskij, G.: The effect of thermomechanical phenomena on the stability of cutting process and wear of cutting tools. SverkhtverdyeMaterialy 6, 66–71 (2003)
Mazur, N.P., Vnukov, Yu.N, Grabchenko, A.I., et al.: Fundamentals of the materials cutting theory, 2nd edn. NTU “KhPI”, Kharkiv (2013)
Altintas, V.: Manufacturing Automation: Metal Cutting Mechanics, Machine Tools Vibrations and CNC Design. Cambridge University Press, Cambridge (2012)
Pavlenko, I.: Static and dynamic analysis of the closing rotor balancing device of the multistage centrifugal pump. Appl. Mech. Mater. 630, 248–254 (2014). https://doi.org/10.4028/www.scientific.net/AMM.630.248
Pavlenko, I.V., Simonovskiy, V.I., Demianenko, M.M.: Dynamic analysis of centrifugal machines rotors supported on ball bearings by combined application of 3D and beam finite element models. In: IOP Conference Series: Materials Science and Engineering, vol. 233, no. 1, p. 01253 (2017). https://doi.org/10.1088/1757-899x/233/1/012053
Oborskyi, G., Orgiyan, A., Tonkonogyi, V., Aymen, A., Balaniuk, A.: Study of dynamic impacts at combined operations of the thin turning and boring. In: Tonkonogyi, V., et al. (eds.) Advanced Manufacturing Processes. InterPartner-2019. Lecture Notes in Mechanical Engineering, pp. 226–235. Springer, Cham (2020). https://doi.org/10.1007/978-3-030-40724-7_23
Orgiyan, A., Tkachenko, B., Oborskyi, G., Balaniuk, A., Iorgachov, V.: Determining rational cutting modes for horizontal boring operation adjusted for the variable rigidity of the process system. In: Tonkonogyi, V., et al. (eds.) Advanced Manufacturing Processes. InterPartner-2019. Lecture Notes in Mechanical Engineering, pp. 246–253. Springer, Cham (2020). https://doi.org/10.1007/978-3-030-40724-7_25
Ostling, D., Tormod, I., Tjomsland, M., Standal, O., Mugaas, N.: Cutting process monitoring with an instrumented boring bar measuring cutting force and vibration. Proc. CIRP 77, 235–238 (2018). https://doi.org/10.1016/j.procir.2018.09.004
Sørby, К., Østling, D.: Precision turning with instrumented vibration-damped boring bars. Proc. CIRP 77, 666–669 (2018). https://doi.org/10.1016/j.procir.2018.08.181
Sørby, K., Sundseth, E.: High-accuracy turning with slender boring bars. Adv. Manuf. 3(2), 105–110 (2015). https://doi.org/10.1007/s40436-015-0112-7
Siddhpura, M., Paurobally, R.: Experimental investigation of chattee vibrations in facing and turning processes. Int. J. Mech. Aerosp. Ind. Mech. Manuf. Eng. 7(6), 968–973 (2013)
Schmitz, T.L., Scott Smith, K.: Machining Dynamics: Frequency Response to Improved Productivity, 2nd edn. Springer, Heidelberg (2008). https://doi.org/10.1007/978-3-319-93707-6
Kopelev, Yu.F., Orgiyan, A.A., Kobelev, V.M.: Parametric of oscillations of machine tools. In: Kopelev, Yu.F. (ed.). Publishing House ONPU, Odessa (2007)
Linchevsky, P.A. Dzhuguryan, T.G., Orgiyan, O.A.: Machining of parts on turning and boring machines. In: Linchevsky, P.A. (ed.). Tekhnika, Kyiv (2000)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 The Editor(s) (if applicable) and The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Orgiyan, A., Kobelev, V., Ivanov, V., Balaniuk, A., Aymen, A. (2020). Ensuring the Bending Stiffness of Pre-compressed Cantilever Boring Bars During Fine Boring. In: Ivanov, V., Trojanowska, J., Pavlenko, I., Zajac, J., Peraković, D. (eds) Advances in Design, Simulation and Manufacturing III. DSMIE 2020. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-50794-7_31
Download citation
DOI: https://doi.org/10.1007/978-3-030-50794-7_31
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-50793-0
Online ISBN: 978-3-030-50794-7
eBook Packages: EngineeringEngineering (R0)