Determination of the loading path for tube hydroforming process of a copper joint using a fuzzy controller Farough MohammadiMahmoud Mosavi Mashadi ORIGINAL ARTICLE 26 August 2008 Pages: 1 - 10
Assessment of flank wear and nose radius wear from workpiece roughness profile in turning operation using machine vision H. H. ShahabiM. M. Ratnam ORIGINAL ARTICLE 13 August 2008 Pages: 11 - 21
An investigation of bell mouthing in precision hole machining with self-piloting tools Mohanad Al-AtaMohammed T. Hayajneh ORIGINAL ARTICLE 30 August 2008 Pages: 22 - 32
Three-dimensional stability lobe and maximum material removal rate in end milling of thin-walled plate Aijun TangZhanqiang Liu ORIGINAL ARTICLE 26 August 2008 Pages: 33 - 39
In-process surface roughness prediction system using cutting vibrations in turning D. R. SalgadoF. J. AlonsoA. Marcelo ORIGINAL ARTICLE 06 September 2008 Pages: 40 - 51
Development of a new method to determine bending sequence in progressive dies M. A. FarsiB. Arezoo ORIGINAL ARTICLE 28 August 2008 Pages: 52 - 60
Self-piercing riveting for aluminium alloys-composites hybrid joints Livan FratiniVincenzo Fortunato Ruisi ORIGINAL ARTICLE 12 August 2008 Pages: 61 - 66
Study on the crushing and hydroforming processes of tubes in a trapezoid-sectional die Shuhui LiXianghe XuZhongqin Lin ORIGINAL ARTICLE 02 September 2008 Pages: 67 - 77
Some studies on temperature profiles in AISI 304 stainless steel sheet during laser beam welding using FE simulation N. Siva ShanmugamG. BuvanashekaranK. Manonmani ORIGINAL ARTICLE 26 August 2008 Pages: 78 - 94
New mask design approach for UV laser micromachining to reduce stitching errors Emir MutapcicPio IovenittiJason Hayes ORIGINAL ARTICLE 29 August 2008 Pages: 95 - 106
Modeling of wire electro-discharge machining of TiC/Fe in situ metal matrix composite using normalized RBFN with enhanced k-means clustering technique Probir SahaDebashis TarafdarKarabi Das ORIGINAL ARTICLE 08 August 2008 Pages: 107 - 116
Effect of delay time on part strength in selective laser sintering Prashant K. JainPulak M. PandeyP. V. M. Rao ORIGINAL ARTICLE 12 August 2008 Pages: 117 - 126
Study on the effect of frequency tracing in ultrasonic-assisted drilling of titanium alloy Ichien HsuC. C. Tsao ORIGINAL ARTICLE 19 August 2008 Pages: 127 - 135
Research on the uncertainties from different form error evaluation methods by CMM sampling Changcai CuiShiwei FuFugui Huang ORIGINAL ARTICLE 14 August 2008 Pages: 136 - 145
Single machine group scheduling with general linear deterioration to minimize the makespan Ji-Bo WangWen-Jun GaoDan Wang ORIGINAL ARTICLE 01 August 2008 Pages: 146 - 150
A new parallel genetic algorithm for solving multiobjective scheduling problems subjected to special process constraint Jiaquan GaoGuixia HeYushun Wang ORIGINAL ARTICLE 13 August 2008 Pages: 151 - 160
Hybrid metaheuristics for unrelated parallel machine scheduling with sequence-dependent setup times Chun-Lung ChenChuen-Lung Chen ORIGINAL ARTICLE 26 August 2008 Pages: 161 - 169
Scheduling sequence-dependent setup time job shops with preventive maintenance B. NaderiM. ZandiehS. M. T. Fatemi Ghomi ORIGINAL ARTICLE 29 August 2008 Pages: 170 - 181
Towards an improved tool to facilitate simulation modelling of complex manufacturing systems Ornella BenedettiniBenny Tjahjono ORIGINAL ARTICLE 13 August 2008 Pages: 191 - 199
Dynamic analysis of a two-stage supply chain—a switched system theory approach Hongwei WangHuixin LiuJian-bo Yang ORIGINAL ARTICLE 02 September 2008 Pages: 200 - 210