Regression equation for selection of design parameters and operating regimes of hydrocyclones used to separate suspensions by dual-stage flotation V. O. Yablonskii Research, Design, Calculations, and Operating Experience Pages: 639 - 646
Computed estimate of safety factors for shell elements of production equipment E. M. SigovaS. V. Doronin OriginalPaper Pages: 647 - 652
Development of designs for polymeric water traps in cooling towers using centrifugal separation forces V. G. AfanasenkoF. Sh. KhafizovE. V. Boev OriginalPaper Pages: 653 - 656
Modeling and use of dissipative heating of rubber in a screw drier F. A. Kougiya OriginalPaper Pages: 657 - 659
Increase in the efficiency of preparing specially pure hydrogen from methane in a high-temperature converter-membrane equipment system A. B. VandyshevV. A. KulikovS. N. Nikishin Cryogenic Engineering, Production and Use of Industrial Gases, Refrigeration Engineering Pages: 660 - 666
Effect of microribbing on the instantaneous convective heat transfer coefficient in the working chamber of an unlubricated piston compressor V. L. YushaD. G. NovikovS. G. Mel’nikov Compressors, Pumps, and Pipeline Fittings Pages: 667 - 670
Turbulent froth equipment for cooling compressed gases A. V. Il’inV. S. KalekinV. A. Plotnikov OriginalPaper Pages: 671 - 675
Dry gas seal systems for equipment with slow shaft rotation N. G. KrivshichS. A. PavlyukD. G. Pshenichnyi Complementary Products and Devices Pages: 676 - 680
Emulsion-film absorber for cleaning flue gases from nitrogen oxides V. S. Ezhov Industrial Ecology Pages: 681 - 685
Behavior of aerosol particles in a suction bunker of standard design O. A. AverkovaV. Yu. ZoryaK. I. Logachev OriginalPaper Pages: 686 - 690
Repairing the piston-cylinder group in a gas motorized compressor L. I. Simma Safety, Diagnosis, and Repair Pages: 691 - 694
Dangers from improper use of aluminum tank cars M. L. MedvedevaA. A. Gorelik Materials Science and Corrosion Protection Pages: 695 - 698
Battery hydrocyclones for chemical plant for treating circulating water and effluents A. I. ProninN. A. KolesovaM. G. Lagutkin Research, Design, Calculations, and Operating Experience Pages: 701 - 706
A centrifugal-regeneration filter for separating dusty gas flows S. Yu. PanovYu. N. ShapovalovM. K. Al’-Kudakh OriginalPaper Pages: 707 - 711
Mass transfer in a low-pressure vortex tube L. A. TarasovaA. V. MorozovO. A. Troshkin OriginalPaper Pages: 712 - 715
Hydraulic resistance of a granular bed in a rising liquid flow Kh. Sh. BakhronovN. Sh. Khudoiberdieva OriginalPaper Pages: 716 - 719
Study of heat exchange during discharge of cryogenic products into water A. M. DomashenkoI. D. Blinova Cryogenic Engineering, Production and Use of Industrial Gases, Refrigeration Engineering Pages: 720 - 725
Cryocrystallization during preparation of ferrites by cryochemical technology V. I. Gulevich OriginalPaper Pages: 726 - 733
Raising efficiency and operating life of rotary compressors with a rolling rotor I. S. BerezinYa. M. StrekA. P. Morgunov Compressors, Pumps, and Pipeline Fittings Pages: 734 - 737
Recommended type of characteristics of gas separators of submersible oil pumps A. N. SherstyukV. E. GavrilovV. A. Yudin OriginalPaper Pages: 738 - 739
Leak tightness of detachable joints with heat-expanded graphite gaskets V. A. AnikeenkoS. G. IonovV. D. Prodan Complementary Products and Devices Pages: 740 - 743
Influence of type of loading on deformation characteristics of fluoroplastic-4 gaskets G. V. Bozhko OriginalPaper Pages: 744 - 748
Study of a model cyclone A. Yu. Val’dbergYu. F. KhutorovS. G. Safonov Industrial Ecology Pages: 749 - 751
Effect of hydrogen on corrosion failure of pipeline metal I. N. Kriminskii Materials Science and Corrosion Protection Pages: 752 - 755
Increase in the operating reliability of a well sucker-rod pump E. D. MokronosovV. V. BogdanovM. N. Eltyshev Manufacturing Technology Pages: 756 - 758
Study of features of final burnishing of ball-valve plugs D. K. ErenchinovV. V. Zimin OriginalPaper Pages: 759 - 762
