Development and study of centrifugal compressor stages with mixed-flow impellers A. M. SimonovV. V. Rossel'V. A. Potanin Eighth Conference on the Compressor Industry (Topical Papers) Pages: 147 - 149
An experimental treatment of the end stages of standardized centrifugal compressors and blowers for natural gas A. A. MiftakhovG. F. Voronov Eighth Conference on the Compressor Industry (Topical Papers) Pages: 150 - 153
Calculation and optimization of shaft end seals for high-pressure centrifugal compressors based on the analysis of friction, dynamics, and thermoelastic hydrodynamic processes A. V. Zuev Eighth Conference on the Compressor Industry (Topical Papers) Pages: 154 - 158
Automated design system for an axial fan I. V. BrusilovskiiV. D. Vermel'Yu. G. Moskovko Eighth Conference on the Compressor Industry (Topical Papers) Pages: 159 - 161
Equipment for granulating melts of ammonium nitrate and carbamide A. N. SelezenevV. N. SakharovI. A. Egorov New Machinery and Equipment Pages: 162 - 165
Flow of non-Newtonian liquid in a closed helical duct of the rotor of a decanter centrifuge D. E. Shkoropad New Machinery and Equipment Pages: 169 - 172
Prediction of the life of equipment according to the change of parameters of the technical state R. G. Mannapov New Machinery and Equipment Pages: 172 - 175
Experimental investigation of the stability of corrugated cylindrical shells V. M. MuratovA. T. TubaivskiiN. T. Bobel' Cryogenic Techniques Pages: 176 - 179
Investigation and design of a thermal protection device for vacuum boosters V. D. ChukhlovI. F. ShmelevV. E. Pashkov Cryogenic Techniques Pages: 180 - 182
Enhancement of the operating efficiency of a combined air cleaner/dehumidifier system Yu. Ya. IgnatovV. É. Mel'nikov Cryogenic Techniques Pages: 182 - 185
Improvement of the efficiency of turbine expansion engines by using microprojections on the rotor disk I. A. DavydenkovA. B. DavydovV. D. Shcherbakov Cryogenic Techniques Pages: 186 - 187
Use of catalysts for the case hardening of metals and alloys Yu. A. Sobolev Cryogenic Techniques Pages: 187 - 188
Improvement of reliability models for sectioned, dry, electrostatic precipitators A. I. Zav'yalov Gas and Waste Water Purification Equipment Pages: 189 - 189
Probability characteristics for electrostatic precipitator reliability V. A. GuzaevM. O. Shteinberg Gas and Waste Water Purification Equipment Pages: 190 - 191
The use of oxides of aluminum and its alloys produced by anodizing in a supercooled electrolyte E. E. Aver'yanovG. F. BakhteevaR. A. Shagiakhmetov Materials Science and Corrosion Control Pages: 192 - 194
Influence of heat application on the corrosion resistance of weld joints of 02Kh8N22S6 steel K. A. YushchenkoV. Yu. Skul'skiiN. A. Adugina Materials Science and Corrosion Control Pages: 194 - 197
Investigation of the properties, structure, and corrosion resistance of the new alloy KhN30MDB M. M. AbelevV. M. GlagolevT. V. Svistunova Materials Science and Corrosion Control Pages: 197 - 200
Optimization of microalloying of 05kh18 ferritic steel for the purpose of increasing plasticity and corrosion resistance L. A. ChigirinskayaO. B. ChulanovN. D. Tomashov Materials Science and Corrosion Control Pages: 200 - 202
Modular concepts of quality assurance in chemical reactor engineering A. D. NikiforovB. S. BronshteinV. A. Panov Equipment-Manufacturing Technology Pages: 203 - 206
Improvement in wear resistance of steel 40KhMFA tool joints by the ionic nitriding method M. V. YaroshenkoL. S. Mirzoyan Equipment-Manufacturing Technology Pages: 207 - 209
Method of cutting gears with more than 100 teeth V. N. Stetsko Equipment-Manufacturing Technology Pages: 209 - 210