Improving the reliability and the technical and economical characteristics of low-pressure air-fractionation units V. P. BelyakovV. F. GustovYu. G. Pisarev OriginalPaper Pages: 151 - 155
Improvement of the design of a condenser-evaporator for air-fractionation units R. I. AkchurinV. A. GarinV. V. Savost'yanov OriginalPaper Pages: 155 - 157
Intensification of heat transfer in a condenser — Evaporator as a result of a porous coating on the boiling surface V. E. PoznyakV. K. OrlovV. N. Savel'ev OriginalPaper Pages: 157 - 160
Improvement in constructions of equipment for switching regenerators in air-separation units A. K. DedkovYu. F. KulikovE. N. Smirnov OriginalPaper Pages: 160 - 162
Block for the complex purification of air of A KzhAzhAArzh-6 unit V. A. GarinS. S. PetukhovN. P. Stasevich OriginalPaper Pages: 162 - 163
Storage features of cryogenic liquids A. B. BulanovV. K. ZheleznyakovN. V. Filin OriginalPaper Pages: 164 - 167
Development and investigation of high-efficiency heat-transfer channels for cryogenic evaporators G. P. Kuz'menkoV. K. OrlovV. E. Poznyak OriginalPaper Pages: 167 - 171
Laminar-vacuum heat insulation of cryogenic equipment based on glass paper made of microthin fiber N. A. MatveevZ. Ya. SyzrantsevaI. M. Dunaevskii OriginalPaper Pages: 171 - 175
Cryogenic cooling systems of transport refrigerators for food products E. V. OnosovskiiB. S. EgurazdovA. N. Vinnikov OriginalPaper Pages: 175 - 179
Cryogenic-vacuum units for scientific purposes V. I. KupriyanovV. V. LeonovV. S. Shishmarev OriginalPaper Pages: 179 - 183
New cryoadsorption vacuum pumps V. P. BelyakovV. I. KupriyanovV. V. Leonov OriginalPaper Pages: 183 - 186
Glues and the technological process of the gluing of heat exchangers made up of perforated plates Yu. P. AlekseevV. I. BulanovM. G. Stepanskii OriginalPaper Pages: 186 - 188
Gas thermoelectric drive of the lock of a cut-off valve N. T. RomanenkoA. F. BykovV. N. Pavlyuk OriginalPaper Pages: 189 - 190
Determination of the mixer type for loose materials by use of nomograms Yu. I. MakarovS. S. KoshkovskiiI. I. Bagrintsev Investigation of the Working Process of Machines and Equipment Pages: 191 - 194
Investigation of the work of a rotary feeder-sprayer G. G. AverbakhM. B. Dubinskii Investigation of the Working Process of Machines and Equipment Pages: 194 - 196
Determination of the height of a gas-liquid bed on bubble plates V. L. YushkoI. D. SergienkoV. P. Muli Investigation of the Working Process of Machines and Equipment Pages: 196 - 198
Chromium coatings with oxides, caebides, and borides I. N. Borodin New Materials and Corrosion Control Pages: 199 - 201
Adhesion of the paper strip to the surface of the rolls in squeezing F. M. BusyginK. V. KornyushinI. N. Gubarev New Materials and Corrosion Control Pages: 202 - 203
Selection of the optimum method of vertical single-pass welding in a narrow gap in A CO2 medium P. M. ÉpshteinV. A. Ermilov Equipment-Manufacturing Technology Pages: 204 - 206
Conditions of obtaining the specified surface finish with the use of Elbor cutters R. M. ÉfendievA. D. DzhafarovR. R. Zeinalov Equipment-Manufacturing Technology Pages: 207 - 209
Influence of hardening by plastic deformation on the roughness of lapped surfaces of fitting gates G. S. Belyaev Equipment-Manufacturing Technology Pages: 209 - 210