Abstract
Modern trends in mechanical engineering are associated with the introduction of green technologies, in particular the use of a minimum quantity lubrication (MQL) in abrasive processing operations. However, due to the low cooling capacity of this technology, the use of cold air (CAMQL) is used increasingly often. This article summarizes the results of comparative tests of the application of this technology, using soy oil as a lubricant. The properties of the surface layer of a nickel alloy obtained after grinding have been studied using electron microscopy, X-ray diffraction analysis, and evaluation of the electron yield by the Kelvin probe method. It was found that when using CAMQL, there is a decrease in oxidative and adhesive processes, while the level of micro-stresses in the surface layer is reduced twice. The results obtained indicate an improvement in the quality of the surface layer when grinding a nickel alloy with CAMQL.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Lee PA (2015) Study on Thermal Characteristics of Micro-Scale Grinding Process Using Nanofluid Minimum Quantity Lubrication (MQL). Int J Precis Eng Manuf 16:1899–1909. https://doi.org/10.1007/s12541-015-0247-2
García E, Méresse D, Pombo I, Dubar M, Sánchez J (2016) Role of frozen lubricant film on tribological behaviour and wear mechanisms in grinding. Int J Adv Manuf Technol 82:1017–1027. https://doi.org/10.1007/s00170-015-7397-3
Reddy PP, Ghosh A (2016) Some critical issues in cryo-grinding by a vitrified bonded alumina wheel using liquid nitrogen jet. J Mater Process Technol 339:329–337. https://doi.org/10.1016/j.jmatprotec.2015.09.040
Nguyen T (2003) An assessment of the applicability of cold air and oil mist in surface grinding. J Mater Process Technol 140:224–230. https://doi.org/10.1016/S0924-0136(03)00714
Choi HZ, Lee SW, Jeong HD (2002) The cooling effects of compressed cold air in cylindrical grinding with alumina and CBN wheels. J Mater Process Technol 127:155–158. https://doi.org/10.1016/S0924-0136(02)00117-6
Saberi A, Parsa H, Ashrafijou M, Rabiei F (2016) Improvement of surface grinding process performance of CK45 soft steel by minimum quantity lubrication (MQL) technique using compressed cold air jet from vortex tube. J Cleaner Prod 131:728–738. https://doi.org/10.1016/j.jclepro.2016.04.10411
Guo SM, Li C et al (2017) Experimental evaluation of the lubrication performance of mixtures of castor oil with other vegetable oils in MQL grinding of nickel-based alloy. J Clean Prod 140:1060–1076. https://doi.org/10.1016/j.jclepro.2016.10.073
Dogra M, Sharma VS, Dureja JS, Gill SS (2018) Environment-friendly technological advancements to enhance the sustainability in surface grinding—a review. J Cleaner Prod 197:218–231. https://doi.org/10.1016/j.jclepro.2018.05.280
Jia DZ, Li CH (2017) Specific energy and surface roughness of minimum quantity lubrication grinding Ni-based alloy with mixed vegetable oil-based nanofluids. Precis Eng J Int Soc Precis Eng Nanotechnol 50:48–62. https://doi.org/10.1016/j.precisioneng.2017.05.012
Mao KQ, Zhang LC (2006) The effect of compressed cold air and vegetable oil on the subsurface residual stress of ground tool steel. J Mater Process Technol 178:9–13. https://doi.org/10.1016/j.jmatprotec.2005.05.013
Krutikova AA, Mitrofanov AP, Parsheva KA (2019) Application of technology for supply of minimum lubricant amount in cooled air flow during heat-resistant alloy grinding. Tekhnologiya Metallov 8:9–15. https://doi.org/10.31044/1684-2499-2019-8-0-9-15
Mitrofanov A, Nosenko V (2019) Investigation of the technology of microdosed supply of lubricant compositions with nanoparticles during grinding of heat-resistant ni-based with additional air cooling. Obrabotka Metallov-Metal Working and Material Science 21:6–18. https://doi.org/10.17212/1994-6309-2019-21.4-6-18
Zhang J, Li C et al (2018) Temperature field model and experimental verification on cryogenic air nanofluid minimum quantity lubrication grinding. Int J Adv Manuf Technol 97:209–228. https://doi.org/10.1007/s00170-018-1936-7
Al-hatab KA, Al-bukhaiti MA, Krupp U, Kantehm M (2011) Cyclic oxidation be-havior of IN 718 superalloy in air at high temperatures. Oxid Met 75:209–228. https://doi.org/10.1007/s11085-010-9230-6
Delaunay F, Berthier C, Lenglet M, Lameille JM (2000) SEM-EDS and XPS studies of the high temperature oxidation behaviour of Inconel 718. Mikrochim Acta 132:337–343. https://doi.org/10.1007/s006040050027
Li W (2006) Influences of tensile strain and strain rate on the electron work function of metals and alloys. Scripta Mater 54:921–924. https://doi.org/10.1016/j.scriptamat.2005.10.064
Hua G, Li D (2011) Generic relation between the electron work function and Young’s modulus of metals. Appl Phys Lett 99(4):041907. https://doi.org/10.1063/1.3614475
Lu H (2016) Electron work function – a promising guiding parameter for material design. Sci Rep 6:1–11. https://doi.org/10.1038/srep24366
Zhou Y, Lu JQ, Qin WG (2009) Change in the electronic work function under different loading conditions. Mater Chem Phys 118:12–14. https://doi.org/10.1016/j.matchemphys.2009.07.062
Shiyi L, Hao L, Li DY (2015) The relationship between the electron work function and friction behavior of passive alloys under different conditions. Appl Surf Sci 351:316–319. https://doi.org/10.1016/j.apsusc.2015.05.125
Melitz W, Shen J, Kummel AC, Lee S (2011) Kelvin probe force microscopy and its application. Surf Sci Rep 66:1–27. https://doi.org/10.1016/j.surfrep.2010.10.001
Wang J, Wang SQ (2014) Surface energy and work function of fcc and bcc crystals: Density functional study. Surf Sci 630:216–224. https://doi.org/10.1016/j.susc.2014.08.017
Acknowledgements
The reported study was funded by RFBR according to the research project № 18-38-00597 “The study of the process of an extreme contact interaction of solids under the conditions of the presence of a minimum amount of refrigerant distributed in a cooled air stream”.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 The Editor(s) (if applicable) and The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Mitrofanov, A.P., Isaeva, A.A., Nosenko, V.A. (2021). State of the Nickel Alloy Surface Layer After Grinding with a Minimum Quantity Lubrication. In: Radionov, A.A., Gasiyarov, V.R. (eds) Proceedings of the 6th International Conference on Industrial Engineering (ICIE 2020). ICIE 2021. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-54817-9_155
Download citation
DOI: https://doi.org/10.1007/978-3-030-54817-9_155
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-54816-2
Online ISBN: 978-3-030-54817-9
eBook Packages: EngineeringEngineering (R0)