Abstract
Polyhydroxyalkanoates are known to be temporarily stored by microorganisms in activated sludge, especially in anaerobic-aerobic processes. Due to the problems resulted from the disposals of plastic wastes and excess sludge of wastewater treatment plants, the production of polyhydroxyalkanoates by treating activated sludge and determining the effect of process variables were the main issues of this paper. In this research, an anaerobic-aerobic sequencing batch reactor was used to make microorganism adapted and a batch aerobic reactor was used for enriching them. The variables affecting polyhydroxyalkanoates production including aeration time, sludge retention time, and volatile fatty acids concentration of the influent in sequencing batch reactor, and also carbon to nitrogen ratio and cultivation time in polymer production reactor, were investigated using Taguchi statistical approach to determine optimum conditions. The maximum polymer production of 29% was achieved at sludge retention time of 5–10 days, aeration time of 2 hours, supplementation of 40% of volatile fatty acids in the influent and increasing of carbon to nitrogen ratio of polymer production reactor to above 25 g/g. Based on the results, in optimum conditions, the volatile fatty acids concentration which increased the production of polyhydroxyalkanoates up to 49% was the most effective variable. Carbon to nitrogen ratio, sludge retention time and aeration time were ranked as the next affecting parameters. Although the polyhydroxyalkanoates content achieved in present study is much lower than that by pure culture, but the proposed method may still serve well as an environmental friendly means to convert waste into valuable product.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
Polymers are known to play an important role in our life because of their desirable properties. Current concerns about the environmental fate of polymeric materials have created much interest in the development of biodegradable polymers.
Among the various biodegradable plastics, polyhydroxyalkanoates (PHAs) are attractive substitutes for conventional petrochemical plastics. PHAs, which are intracellular storage materials, have many potential applications in medicine, agriculture, pharmacy, and packaging due to their biodegradability and biocompatibility. They accumulate as distinct inclusions in the cell and comprise up to 80% of the dry cell weight for strains of ralstonia eutropha (previously known as alcaligenes eutrophus), under conditions of nitrogen or phosphate limitation and excess carbon source [1, 2]. Production and recovery of poly-Β-hydroxyl-butyrate from whey degradation by Azotobacter was examined by Khanafari et al. [3]. In this research after 48 h, in presence of meat extract as the source of nitrogen, poly-β hydroxyl-butyrate production was increased up to 75% of the cell dry weight.
Polymers produced from PHAs have been reported to be completely biodegradable [4, 5]. In addition, because they are produced from renewable resources, they are attractive to human beings as environmentally friendly materials [6]. Even though PHAs have been recognized as good candidates for biodegradable polymers, their high price compared with that of petrochemical-based polymers has limited their use in a wide range of applications [7, 8].
The production of biodegradable plastic on a large scale is limited because of the relative expense of the substrate, low polymer production, and the cost of extraction and recovery. According to Yamane [9], higher costs, especially raw material cost, make it difficult for PHAs biodegradable plastics to compete with conventional petroleum-based plastics in the commercial market place. Almost 30% of total PHAs production cost is attributed to the carbon source [10]. The use of inexpensive feed-stocks for competitive bioplastics (PHAs) production was recommended by Gonzalez-Lopez et al. [11]. Ramos-Cormenzana et al. [12] used olive-mill wastewater (alpechin) for biodegradable plastics production.
A good candidate for economical PHAs production would be a mixed culture (such as activated sludge) that can store high PHAs content while growing on an inexpensive substrate. Nowadays a great amount of excess sludge is generated daily in the world. Additionally, about 40 to 60 percent of the investment expenses of the activated sludge treatment plants have to do with treating the sludge coming from the wastewater treatment plants [13–15]. One possible strategy for excess sludge management is reutilization of sludge as useful resources.
During last two decades, many researchers have been investigating PHAS production by using activated sludge. Mino et al. [16] used the activated sludge acclimatized in the anaerobic-aerobic process for enhanced biological phosphate removal to accumulate PHAS. Satoh et al. [17] studied PHAS production by using activated sludge and compared it with that produced by pure culture. Chua et al. [18] studied the effect of acetate concentration in influent, pH and sludge retention time (SRT) on the production of PHAS by activated sludge treating municipal wastewater. Fermentative volatile fatty acids (VFAs) as carbon sources to synthesize PHAS by activated sludge were examined by Cai et al. [19]. In another study, it was found that activated sludge from a pulp and paper industry wastewater treatment plant had the best potential for PHAS production among activated sludge from municipal, industrial starch, and industrial dairy wastewater treatment plants, in laboratory scale experiments [20]. Release of intracellular polymeric substances from activated sludge caused the increment of sludge dewatering capability and was considered as an effective method for sludge volume reduction [21].
The production system of PHAs as biodegradable plastics by activated sludge that inspired from Takabatake et al. [22] is shown in Figures 1. In this system at first, activated sludge with high potential of PHAs production was acclimatized in “PHAs accumulating bacteria enrichment reactor”. In this stage, it was essential to optimize the operational conditions for sludge acclimatization or for the enrichment of PHAs accumulating microorganisms, so that the PHAs production capability of activated sludge could be improved. In the second step, the acclimatized activated sludge was transferred into PHA production reactor (PPR). In this reactor, wastewater with high concentration of VFAs was fed as carbon sources for PHAs production.
In the present work, our focus was mainly on the optimization of operational conditions and determining the effect of each process variable. For this purpose, an anaerobic-aerobic sequencing batch reactor (SBR) and a fully aerobic batch process were selected for microorganism acclimatization and PHAs production, respectively. The operational conditions being investigated were the carbon to nitrogen ratio (C: N) of influent, cultivation time in PPR, aeration time, SRT, and VFAs concentration of influent in SBR.
Materials and methods
Operation of SBR under different operational condition
The schematic of a 10-liter SBR, which was operated in the anaerobic-aerobic mode, is shown in Figures 2. It was operated with synthetic wastewater with the specification shown in Table 1 as the influent.
In order to change VFAS concentration in the substrate solution, carbon sources were replaced with the desired amount of sodium acetate and sucrose. The reactor was put in a room with constant temperature of 23-25°C. The origin of the seed was sludge of municipal wastewater treatment plant in Tehran.
The SBR was operated continuously in cycles of 4, 5, or 6 hours. One standard cycle consisted of 15 min for decantation, 5 min for influent feeding, 10 min for nitrogen purging, 1 hour for anaerobic, 2, 3 or 4 hours for aerobic and 30 min for sedimentation periods. Substrate solution was added at the end of nitrogen purging phase. In the aerobic phase, air was supplied by an aeration pump to obtain the minimum dissolved oxygen concentration of 2 mg/ L.
The SRT was controlled at three different operational conditions of 5, 10, and 15 days. For each change of SRT at least three times of the selected SRT was considered for adaptation. A sludge circulation pump in the anaerobic phase and the supply of air under the aerobic conditions provided the mixing of activated sludge mixed liquor. The SBR was completely automated and controlled by an electrical control box.
PHASproduction reactor
In order to measure the PHAS production potential of activated sludge, batch experiments were conducted under aerobic conditions. Activated sludge was taken at the end of aerobic phase of SBR, and put in a glass jar as shown in Figures 3. Sodium acetate was added as carbon source for PHAS production and incubated in aerobic condition. Based on preliminary test for acetate uptake rate (not shown in this paper), in each experiment 500 mg/L carbon source was added at t = 0, and then 250 mg /L at t = 6, 12 and 18 hours. In this reactor, pH had a tendency to increase and was kept between 7–7.5 by adding diluted sulfuric acid.
To change carbon to nitrogen ratio in the influent of PPR, ammonium sulfate was used as the nitrogen source. K2HPO4 was also added in order to supply phosphate requirement of the system. The batch experiments were conducted under the same temperature as SBR.
In all batch experiments, one sample was taken at 0, 6, 12, 18 and 24 hours, respectively, for analysis. Addition of acetate and sampling from PPR during different periods of time were also completely automated.
Analytical methods
All parameters except PHAs were analyzed according to APHA, AWWA, WEF [23]. PHAs concentration of suspension (activated sludge mixed liquor) was determined by gas chromatography (GC) after methanolytic decomposition of activated sludge in acidified hot chloroform [24]. The GC used for this purpose (Philips-PU4410) was equipped with a capillary column (BP-5, SEG. Austria, 25 m length, 220 μm internal diameter, less than 1 μm film thickness) and a flame ionization detector. The detector and injector temperature were adjusted to 200°C. Initial temperature setting of column was 100°C for 2 min., then increased in 8°C/min to 140°C and was maintained for 5 min. One micro liter of sample was split injected into the GC column (split ratio was 1:25). Sodium 3-hydroxybutirate (Sigma, USA) and copolymer (88:12 wt%) of 3-hydroxybutirate (3HB) and 3-hydroxyvalerate (3HV) (Sigma, USA) were used as the standard for the quantification of 3HB and 3HV, respectively. As acetate was used as the carbon source in this study, the monomeric unit of the produced PHAs was almost all 3HB. All other chemicals employed for analysis were of analytical grade and obtained from reliable companies.
Design of experiment and analysis of variance
Production of PHAS by activated sludge process is affected by numerous variables. In this research, to investigate the effect of different factors (including: aeration time, SRT, VFAs content of influent and C: N of PPR) and to determine the optimum conditions of the process, the statistical Taguchi approach was applied [25].
Based on the results of other researchers, 3 levels were selected for each of four chosen factors [18, 26]. The considered levels for these variables in an L9 orthogonal array are given in Table 2. Each experiment (trial) was repeated tree times, and the average of corresponding results in terms of the percentage of PHAS production is also shown in this Table.
The analysis of the experimental results by this method is expressed in terms of the main effects of each factor, which is defined as the average of the results for a factor at a specified level.
Results
Effect of cultivation time
To study the effect of cultivation time of activated sludge on the PHAS production potential, preliminary experiments were carried out at 23-25°C for periods of 0–30 hours. The relationship between cultivation time and PHAS production, which was positive, is shown in Figures 4. As shown, accumulation of PHAS into the cell walls increased with increasing of cultivation time. Based on these result, although maximum productivity happened after 18 hours, but a cultivation time of 24 hours was chosen for further experiments.
Analysis of the results by the Taguchi method
To study the effect of process variables on the PHAS production by activated sludge, the statistical Taguchi method was applied for the design of the experiments as described before. The percentages of PHAS production, given in Table 2 for each experiment, were used to calculate the main effects of the factors. These results are shown in Figures 5 and will be discussed in the following section. The analysis of the results is also summarized in Table 3. According to the analysis of variance, in optimum conditions, VFAS which increased the production of PHAs up to 49% was the most effective variable. C:N of PPR influent, sludge retention time and aeration time with about 28%, 13% and 10% increasing of polymer production, were ranked as the next responsibles.
Discussion
As shown in Figures 5a, the PHAs production capability of activated sludge acclimatized in SRT of 5 days decreased with increasing of aeration time from 2 to 4 hours. Same trend was observed for both SRTs of 10 and 15 days (Figure not shown).
The reason why at longer aeration time less PHAs was produced, is that as aeration time increases the substrate concentration decreases and microorganisms are forced to declining growth and then endogenous phase [27]. In this phase not only the microbial population is reduced but also microbial communities, which are dominants in the system, may change. Therefore, longer aeration time may select microbial community with lower PHAs production capacity than that selected under shorter aeration times. At lower than 2 hours aeration time, the system may be at log-growth phase. During this period an excess amount of food exists and the population of microorganisms is less than that in stationary phase. As a result, activated sludge processes operating in stationary phase can produce more PHAs compared to that with endogenous or log-growth phases. Based on these results, the optimum aeration time for PHAs production for this system was chosen to be 2 hours.
Figures 5b shows that increasing of SRT up-to 5 days had considerable effect on the PHAs production. However, a further increase of SRT had no significant effect on polymer production ability. The initial increase of PHAs production capability can be related to the difference in organic loading to biomass. Dionisi et al. [28] showed in their anoxic batch tests that a maximum PHAs storage might occur at intermediate organic loading rate. A practically stable trend attained for PHAs production by further increase of sludge retention time can be possibly attributed to the reduction of sludge yield under a longer SRT [18]. On the basis of these results, although there was no significant difference between PHAs production predicted (by Software) in SRTs of 5 to 10 days, but 10 days was selected as the optimum SRT for PHAs production.
The effect of VFAs content of SBR feed on PHAs production is shown in Figures 5c. It seems that supplementation of 40% acetate in influent wastewater considerably improved the PHAs production capability of activated sludge, but a further increase of VFAs had not considerable effect on the PHAs production. These results suggest that, in acetate-rich acclimatization, the PHAs storage capacity of microorganisms might be increased, thus leading to a higher PHAs production capacity. It is therefore suggested that the wastewater containing volatile fatty acids should be used to enhance the PHAs production capability of acclimatized sludge.
As shown in Figures 5d increasing of C: N up to 25 g/g increased PHAs production, but further increase of C:N on the PHAs production was not considerable. This behavior can be reasoned as follows:
1-Coexistence of nitrogenous compounds increases acetate uptake rate of activated sludge. However, it is used to promote the productivity of structural materials such as intracellular carbohydrates (ICH) and protein [22].
2-Further increasing of nutrient concentration in the substrate may act as the limiting material for cell synthesis and growth [27], as well as for acetate uptake rate and PHAs production.
On the basis of these results, 25 g/g was selected as optimum C:N for the PHAs production.
Based on the results of this study, the optimum conditions for the production of PHAs using activated sludge were 2 hours for aeration time, 5 to 10 days of SRT, supplementation of 40% of VFAs in the influent of SBR, and more than 25 g/g of C:N for PPR. The optimum condition coincides with trial (experiment No.2 in Table 2), at which the PHAs production was 29%. Although the PHAs content achieved in present study was much lower than that by pure culture, but the proposed method may still serve well as an environmental friendly means to convert waste into valuable product.
References
Lee SY: Bacterial poly-hydroxyalkanoates. Biotechnol Bioeng. 1996, 49: 1-14. 10.1002/(SICI)1097-0290(19960105)49:1<1::AID-BIT1>3.3.CO;2-1.
Zinn M, Witholt B, Egli T: Occurrence Synthesis and Medical Application of Bacterial Polyhydroxyalkanoate. Adv Drug Delivery rev. 2001, 53: 5-21. 10.1016/S0169-409X(01)00218-6.
Khanafari A, Akhavan Sepahei A, Mogharab M: Production and recovery of Poly-Β-Hydroxybutirate from whey Degradation by Azotobacter. Iran. J. Environ. Health. Sci. Eng. 2006, 3 (3): 193-198.
Anderson AJ, Dawes EA: Occurrence, metabolism, metabolic role, and industrial uses of bacterial poly-hydroxyalkanoates. Microbiol Rev. 1990, 54: 450-472.
Doi Y: Microbial polyesters. 1990, New York: VCH, ISBN 978-0-444-50563-7
Matsuo T, Hanaki K, Takizawa S, Satoh H: Advances in Water and Wastewater Treatment Technology. 2001, London: Elsevier Sci, 249-260.
Ayorinde FO, Saeed KA, Price E, Morrow A, Collins WE, Mclnnis F, Pollack SK, Eribo BE: Production of Poly (ß-hydroxybutyrate) From Saponified Vernonia Galamensis Oil by Alcaligenes Eutrophus. J Ind Microbiol Biotechnol. 1998, 21: 46-50. 10.1038/sj.jim.2900555.
Hejazi P, Vasheghani FE, Yamini Y: Supercritical Fluid Disruption of Ralstonia eutropha for Poly (β-hydroxybutyrate) Recovery. Biotechnol Progr. 2003, 19: 1519-1523. 10.1021/bp034010q.
Yamane T: Yield of poly-D (−)-3Hydroxybutyrate from various carbon sources A theoretical study. Biotechnol and Bioeng. 1993, 41: 165-170. 10.1002/bit.260410122.
Salehizadeh H, Van Loosdrecht MCM: Production of Polyhydroxyalkanoates by mixed culture: recent trends and biotechnological importance. Biotechnol Adv. 2004, 22: 261-279. 10.1016/j.biotechadv.2003.09.003.
Gonzalez-Lopez J, Pozo C, Martinez-Toledo MV, Rodelas B, Salmeron V: Production of polyhydroxyalkanoates by Azotobacter chroococcum H23 in wastewater from olive oil mills (alpechin)”. Int Biodeterior Biodegrad. 1996, 38: 271-276. 10.1016/S0964-8305(96)00060-1.
Ramos-Cormenzana A, Monteoliva-Sánchez M, López MJ: Bioremediation of alpechín. Int Biodeterior Biodegrad. 1995, 35: 249-268. 10.1016/0964-8305(95)00033-2.
Liu Y, Tay J: Strategy for minimization of excess sludge production from the activated sludge process. Biotech Adv. 2001, 19 (2): 97-107. 10.1016/S0734-9750(00)00066-5.
Takdastan A, Mehrdadi N, Azimi AA, Torabian A, Nabi Bidhendi GR: Investigation of intermittent chlorination system in biological excess sludge reduction by sequencing batch reactors. Iran. J. Environ. Health. Sci. Eng. 2009, 6 (1): 53-60.
Wang W, Jung Y, Kiso Y: Excess sludge reduction performance of an aerobic SBR process equipped with a submerged mesh filter unit. proceesBiochemistry. 2006, 41: 745-751.
Mino T, Van Loosdrecht MCM, Heijnen JJ: Microbiology and biochemistry of the enhanced biological phosphate removal process. Water Sci Technol. 1998, 32: 3193-3207.
Satoh H, Mino T, Matsuo T: PHA production by activated sludge. Int J Biol Macromol. 1999, 25: 105-109. 10.1016/S0141-8130(99)00021-5.
Chua ASM, Takabatake H, Satoh H, Mino T: Production of polyhydroxyalkanoates (PHAS) by activated sludge treating municipal wastewater: effect of pH, sludge retention time (SRT), and acetate concentration in influent. Water Res. 2003, 37: 3602-3610. 10.1016/S0043-1354(03)00252-5.
Cai M, Chua H, Zhao Q, Sin NS, Ren J: Optimal production of Polyhydroxyalkanoates (PHA) in activated sludge fed by volatile fatty acids (VFAs) generated from alkaline excess sludge fermentation. Bioresource Technol. 2009, 100: 1399-1405. 10.1016/j.biortech.2008.09.014.
Yan S, Tyagi RD, Surampalli RY: Polyhydroxyalkanoates (PHA) production using wastewater as carbon source and activated sludge as microorganisms. Water Sci Technol. 2006, 53: 175-180.
Hosnani E, Nosrati M, Shojasadati SA: Role of Extracellular Polymeric Substances in Dewaterability of Untreated Sonicated and Digested Waste Activated Sludge. Iran. J. Environ. Health. Sci. Eng. 2010, 7 (5): 395-400.
Takabatake H, Satoh H, Mino T, Matsuo T: Recovery of biodegradable plastics from activated sludge process. Water Sci Technol. 2000, 42: 351-356.
APHA, AWWA, WEF: Standard Methods for the Examination of Water and Wastewater. 1998, Washington DC, USA: Amer. Public Health Assoc, 20
Braunegg G, Sonnleitner B, Lafferty RM: A Rapid Gas Chromatographic Method for the Determination of Polyhydroxybutiric Acid in Microbial Biomass. Eur J Appl Microbiol Biotechnol. 1978, 6: 29-37. 10.1007/BF00500854.
Roy RK: A Primer on the Taguchi Method. 1990, New York; Van No strand Reinhold, 40-99.
Mokhtarani N, Ganjidust H, Vasheghani Farahani E, Khaleghi Sarnamy M: Effect of VFAs in the production of Polyhydroxyalkanoates by activated sludge. Iranian J. of Polym. Sci. & Technol. 2008, 21: 83-90.
Metcalf and Eddy Inc: Wastewater Engineering, Treatment and Reuse. 2003, New York: McGraw-Hill, 565-566. 4
Dionisi D, Majone M, Ramadori R, Beccari M: The storage of acetate under anoxic conditions. Water Res. 2001, 35: 2661-2668. 10.1016/S0043-1354(00)00562-5.
Acknowledgements
The authors are grateful to Guilan Water and Wastewater Company for financial support. The authors also wish to thank Ms. S. Ganjidoust from wastewater laboratory of civil and environmental engineering faculty of Tarbiat Modares University, for her technical supports.
Author information
Authors and Affiliations
Corresponding author
Additional information
Competing interests
The authors declare that they have no competing interests.
Authors’ contributions
The overall implementation of this study including design, experiments and data analysis, and manuscript preparation were the results of efforts by Corresponding author. All authors have made extensive contribution into the review and finalization of this manuscript. All authors read and approved the final manuscript.
Authors’ original submitted files for images
Below are the links to the authors’ original submitted files for images.
Rights and permissions
This article is published under license to BioMed Central Ltd. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
About this article
Cite this article
Mokhtarani, N., Ganjidoust, H. & Vasheghani Farahani, E. Effect of process variables on the production of Polyhydroxyalkanoates by activated sludge. J Environ Health Sci Engineer 9, 6 (2012). https://doi.org/10.1186/1735-2746-9-6
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/1735-2746-9-6