Skip to main content
SpringerLink
Log in

Transient lubrication of piston compression ring during cold start-up of SI engine

  • Published:
International Journal of Precision Engineering and Manufacturing-Green Technology Aims and scope Submit manuscript

Abstract

Cold start-up conditions differ from the normal operating conditions for an engine, and this discrepancy adversely affects the tribological performance of interfaces. The majority of health-hazardous engine exhaust emissions occur during the cold start-up of an engine; consequently this condition generates a major environmental concern. This study numerically investigates the transient hydrodynamic lubrication of the first compression ring during initial start-up of a cold engine by combining lubrication theory with the realistic oil rheology of multigrade oils. Specifically, in this study transient speed, variation in cylinder pressure, and high lubricant viscosity during start-up are considered to determine developing pattern of the lubricating film and of other tribological performance parameters. The cycle-by-cycle developments of lubricating film, friction force, power loss, and oil transport are analyzed as well. The start-ups of a cold and a warm engine are also compared in terms of frictional losses and oil transport. Different monograde and multigrade engine oils are used to evaluate oil-dependent performance. Results show that in all cases, performance during cold start-up is of greater significance than that of a warm engine. Low lubricant temperature and stated start-up conditions substantially increase amount of energy loss and net oil transport. Temperature-dependent variations in performance are also more significant in high viscosity-grade oils.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Kayes, D. and Hochgreb, S., “Time, Space, and Species Resolved Measurements of Engine-out Hydrocarbon Emissions from Spark-Ignited Engines,” Combustion Science and Technology, Vol. 127, No. 1–6, pp. 333–362, 1997.

    Article  Google Scholar 

  2. Cook, R., Touma, J. S., Fernandez, A., Brzezinski, D., Bailey, C., et al., “Impact of Underestimating the Effects of Cold Temperature on Motor Vehicle Start Emissions of Air Toxics in the United States,” Journal of the Air and Waste Management Association, Vol. 57, No. 12, pp. 1469–1479, 2007.

    Article  Google Scholar 

  3. Liu, Z., Li, L., and Deng, B., “Cold Start Characteristics at Low Temperatures Based on the First Firing Cycle in an Lpg Engine,” Energy Conversion and Management, Vol. 48, No. 2, pp. 395–404, 2007.

    Article  Google Scholar 

  4. Gumus, M., “Reducing Cold-Start Emission from Internal Combustion Engines by Means of Thermal Energy Storage System,” Applied Thermal Engineering, Vol. 29, No. 4, pp. 652–660, 2009.

    Article  Google Scholar 

  5. Tronci, S., Baratti, R., and Gavriilidis, A., “Catalytic Converter Design for Minimisation of Cold-Start Emissions,” Chemical Engineering Communications, Vol. 173, No. 1, pp. 53–77, 1999.

    Article  Google Scholar 

  6. Huang, Z., Guo, H., Pan, K., Zhou, L., and Jiang, D., “Prediction and Experimental Study on Hydrocarbon Emissions from Combustion Chamber Deposits in a Spark Ignition Engine,” Combustion Science and Technology, Vol. 131, No. 1–6, pp. 67–83, 1998.

    Article  Google Scholar 

  7. Tian, T., “Dynamic Behaviours of Piston Rings and Their Practical Impact. Part 1: Ring Flutter and Ring Collapse and Their Effects on Gas Flow and Oil Transport,” Proc. of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Vol. 216, No. 4, pp. 209–228, 2002.

    Article  Google Scholar 

  8. Tian, T., “Dynamic Behaviours of Piston Rings and Their Practical Impact. Part 2: Oil Transport, Friction and Wear of Ring/Liner Interface and the Effects of Piston and Ring Dynamics,” Proc. of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Vol. 216, No. 4, pp. 229–248, 2002.

    Article  Google Scholar 

  9. Rahmani, R., Theodossiades, S., Rahnejat, H., and Fitzsimons, B., “Transient Elastohydrodynamic Lubrication of Rough New or Worn Piston Compression Ring Conjunction with an Out-of-Round Cylinder Bore,” Proc. of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Paper No. 1350650111431028, 2012.

    Google Scholar 

  10. Baker, C. E., Theodossiades, S., Rahnejat, H., and Fitzsimons, B., “Influence of in-Plane Dynamics of Thin Compression Rings on Friction in Internal Combustion Engines,” Journal of Engineering for Gas Turbines and Power, Vol. 134, No. 9, Paper No. 092801, 2012.

    Article  Google Scholar 

  11. Daniels, C. C. and Braun, M. J., “The Friction Behavior of Individual Components of a Spark-Ignition Engine during Warm-Up,” Tribology Transactions, Vol. 49, No. 2, pp. 166–173, 2006.

    Article  Google Scholar 

  12. Ahmadi, H., Rashidi, A., and Mohtasebi, S.-S., “Investigation of the Anti-Wear Properties of Nano Additives on Sliding Bearings of Internal Combustion engines,” Int. J. Precis. Eng. Manuf., Vol. 14, No. 5, pp. 805–809, 2013.

    Article  Google Scholar 

  13. Roberts, A., Brooks, R., and Shipway, P., “Internal Combustion Engine Cold-Start Efficiency: A Review of the Problem, Causes and Potential Solutions,” Energy Conversion and Management, Vol. 82, pp. 327–350, 2014.

    Article  Google Scholar 

  14. Shayler, P., Allen, A., Leong, D., Pegg, I., Brown, A., et al., “Characterising Lubricating Oil Viscosity to Describe Effects on Engine Friction,” SAE Technical Paper, DOI No. 10.4271/2007–01-1984, 2007.

    Google Scholar 

  15. Datoo, A. N. and Fox, M. F., “An Initial Investigation of the Lubricant Condition in the Automotive Ring Zone under Cold Start Conditions,” Tribology Series, Vol. 41, pp. 517–522, 2003.

    Article  Google Scholar 

  16. Becker, E. P., “Trends in Tribological Materials and Engine Technology,” Tribology International, Vol. 37, No. 7, pp. 569–575, 2004.

    Article  Google Scholar 

  17. Han, D.-C. and Lee, J.-S., “Analysis of the Piston Ring Lubrication with a New Boundary Condition,” Tribology International, Vol. 31, No. 12, pp. 753–760, 1998.

    Article  Google Scholar 

  18. Yong, Z., Guohua, C., and Bing, L., “Two Dimensional Numerical Analysis of Piston Ring Lubrication of an Internal Combustion Engine,” SAE Technical Paper, DOI No. 10.4271/1999–01-1222, 1999.

    Google Scholar 

  19. Bolander, N. W. and Sadeghi, F., “Deterministic Modeling of Honed Cylinder Liner Friction,” Tribology Transactions, Vol. 50, No. 2, pp. 248–256, 2007.

    Article  Google Scholar 

  20. Ali, S. H. R., Mohamed, H. H., and Bedewy, M. K., “Identifying Cylinder Liner Wear Using Precise Coordinate Measurements,” Int. J. Precis. Eng. Manuf., Vol. 10, No. 5, pp. 19–25, 2009.

    Article  Google Scholar 

  21. Mishra, P., Balakrishnan, S., and Rahnejat, H., “Tribology of Compression Ring-to-Cylinder Contact at Reversal,” Proc. of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Vol. 222, No. 7, pp. 815–826, 2008.

    Article  Google Scholar 

  22. Morris, N., Rahmani, R., Rahnejat, H., King, P., and Fitzsimons, B., “Tribology of Piston Compression Ring Conjunction under Transient Thermal Mixed Regime of Lubrication,” Tribology International, Vol. 59, pp. 248–258, 2013.

    Article  Google Scholar 

  23. Shahmohamadi, H., Rahmani, R., Rahnejat, H., Garner, C. P., and King, P., “Thermo-Mixed Hydrodynamics of Piston Compression Ring Conjunction,” Tribology Letters, Vol. 51, No. 3, pp. 323–340, 2013.

    Article  Google Scholar 

  24. Avan, E. Y., Spencer, A., Dwyer-Joyce, R. S., Almqvist, A., and Larsson, R., “Experimental and Numerical Investigations of Oil Film Formation and Friction in a Piston Ring-Liner Contact,” Proc. of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Paper No. 1350650112464706, 2012.

    Google Scholar 

  25. Jeng, Y.-R., “Theoretical Analysis of Piston-Ring Lubrication Part I: Fully Flooded Lubrication,” Tribology Transactions, Vol. 35, No. 4, pp. 696–706, 1992.

    Article  MathSciNet  Google Scholar 

  26. Eilon, S. and Saunders, O., “A Study of Piston-Ring Lubrication,” Proc. of the Institution of Mechanical Engineers, Vol. 171, No. 1, pp. 427–462, 1957.

    Article  Google Scholar 

  27. Ma, M., Smith, E., and Sherrington, I., “A Three-Dimensional Analysis of Piston Ring Lubrication Part 1: Modelling,” Proc. of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Vol. 209, No. 1, pp. 1–14, 1995.

    Article  Google Scholar 

  28. Dowson, D., Ruddy, B., and Economou, P., “The Elastohydrodynamic Lubrication of Piston Rings,” Proc. of the Royal Society of London A: Mathematical, Physical and Engineering Sciences, pp. 409–430, The Royal Society, 1983.

    Google Scholar 

  29. Yang, Q. and Keith, T. G., “Two-Dimensional Piston Ring Lubrication-Part II: Elastic Ring Consideration,” Tribology Transactions, Vol. 39, No. 4, pp. 870–880, 1996.

    Article  Google Scholar 

  30. Ma, M., Sherrington, I., and Smith, E., “Analysis of Lubrication and Friction for a Complete Piston-Ring Pack with an Improved Oil Availability Model: Part 1: Circumferentially Uniform Film,” Proc. of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Vol. 211, No. 1, pp. 1–15, 1997.

    Article  Google Scholar 

  31. Ma, M., Smith, E., and Sherrington, I., “Analysis of Lubrication and Friction for a Complete Piston-Ring Pack with an Improved Oil Availability Model: Part 2: Circumferentially Variable Film,” Proc. of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, Vol. 211, No. 1, pp. 17–27, 1997.

    Article  Google Scholar 

  32. Sherrington, I. and Smith, E., “Experimental Methods for Measuring the Oil-Film Thickness between the Piston-Rings and Cylinder-Wall of Internal Combustion Engines,” Tribology International, Vol. 18, No. 6, pp. 315–320, 1985.

    Article  Google Scholar 

  33. Tian, T., Wong, V., and Hochgreb, S., “Analysis of the Piston Ring/ Liner Oil Film Development during Warm-Up for an SI-Engine,” Journal of Engineering for Gas Turbines and Power-Transactions of the Asme, Vol. 123, No. 1, pp. 109–116, 2001.

    Article  Google Scholar 

  34. Zhang, J., Shen, T., and Marino, R., “Model-Based Cold-Start Speed Control Scheme for Spark Ignition Engines,” Control Engineering Practice, Vol. 18, No. 11, pp. 1285–1294, 2010.

    Article  Google Scholar 

  35. Cha, P. D., Rosenberg, J. J., and Dym, C. L., “Fundamentals of Modeling and Analyzing Engineering Systems,” Cambridge University Press, 2000.

    Google Scholar 

  36. Rao, J. S. and Dukkipati, R. V., “Mechanism and Machine Theory,” New Age International, 2nd Ed., 1992.

    Google Scholar 

  37. Ji, C., Liang, C., Gao, B., Wei, B., Liu, X., et al., “The Cold Start Performance of a Spark-Ignited Dimethyl Ether Engine,” Energy, Vol. 50, pp. 187–193, 2013.

    Article  Google Scholar 

  38. Lejsek, D. and Kulzer, A., “Investigations on the Transient Wall Heat Transfer at Start-Up for SI Engines with Gasoline Direct Injection,” SAE International Journal of Engines, Vol. 2, No. 1, pp. 381–397, 2009.

    Article  Google Scholar 

  39. Ku, B.-C., Han, Y.-C., Lee, J.-E., Lee, J.-K., Park, S.-H., et al., “Tribological Effects of Fullerene (c60) Nanoparticles Added in Mineral Lubricants according to Its Viscosity,” Int. J. Precis. Eng. Manuf., Vol. 11, No. 4, pp. 607–611, 2010.

    Article  Google Scholar 

  40. Vogel, H., “The Law of Relation between the Viscosity of Liquids and the Temperature,” Physik Z, Vol. 22, pp. 645–646, 1921.

    Google Scholar 

  41. Ma, M. T., “Incorporation of Lubricant Shear-Thinning in a Two-Dimensional Lubrication Analysis for Automotive Piston-Ring Packs,” SAE Technical Paper, DOI No. 10.4271/2000–01-1786, 2000.

    Google Scholar 

  42. Wong, P., Wang, R., and Lingard, S., “Pressure and Temperature Dependence of the Density of Liquid Lubricants,” Wear, Vol. 201, No. 1, pp. 58–63, 1996.

    Article  Google Scholar 

  43. Quan-Bao, Z., Tie-Zhu, Z., and Rong-Sheng, W., “A Full Lubrication Model for Rough Surface Piston Rings,” Tribology International, Vol. 21, No. 4, pp. 211–214, 1988.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. School of Mechanical Engineering, Kyungpook National University, 80, Daehak-ro, Buk-gu, Daegu, 41566, South Korea

    Ali Usman & Cheol Woo Park

Authors
  1. Ali Usman
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Cheol Woo Park
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Cheol Woo Park.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Usman, A., Park, C.W. Transient lubrication of piston compression ring during cold start-up of SI engine. Int. J. of Precis. Eng. and Manuf.-Green Tech. 3, 81–90 (2016). https://doi.org/10.1007/s40684-016-0011-9

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40684-016-0011-9

Keywords

Search

Navigation