Abstract
This paper presents an effective method for finding optimum location of unified power quality conditioner (UPQC) and distributed static compensator (D-STATCOM) in radial distribution system. The bus having the minimum losses is selected as the candidate bus for UPQC placement and the optimal location of D-STATCOM is found by power loss index (PLI) method. The PLI values of all the buses are calculated and the bus having the highest PLI value is the most favorable bus and thus selected as candidate bus for D-STATCOM placement. Main contribution of this paper are: (i) finding optimum location of UPQC in radial distribution system (RDS) based on minimum power loss; (ii) finding the optimal size of UPQC which offers minimum losses; (iii) calculation of annual energy saving using UPQC and D-STATCOM; (iv) cost analysis with and without UPQC and D-STATCOM placement; and (v) comparison of results with and without UPQC and D-STATCOM placement in RDS. The algorithm is tested on IEEE 33-bus and 69-bus radial distribution systems by using MATLAB software.
Similar content being viewed by others
References
P. Bapaiah, Power quality improvement by using D-STATCOM. Int. J. Emerg. Trends Electr. Electron. 2(4), 1–12 (2013)
S.A. Taher, S.A. Afsari, Optimal location and sizing of UPQC in distribution networks using differential evolution algorithm. Math. Probl. Eng. (2012). doi:10.1155/2012/838629,(838629),1-20
M. Hosseini, H.A. Shayanfar, M.F. Firuzabad, Modelling of unified power quality conditioner (UPQC) in distribution systems load flow. Energy Convers. Manag. 50(6), 1578–1585 (2009)
S. Ganguly, Unified power quality conditioner allocation for reactive power compensation of radial distribution networks. IET Gener. Transm. Distrib. 8(8), 1418–1429 (2014)
S.A. Taher, S.A. Afsari, Optimal location and sizing of D-STATCOM in distribution systems by immune algorithm. Electr. Power Energy Syst. 6, 34–44 (2014)
J.H. Teng, A direct approach for distribution system load flow solutions. IEEE Trans. Power Deliv. 18(3), 882–887 (2003)
M.H. Haque, Efficient load flow method for distribution systems with radial or meshed configuration. IEE Proc. Gener. Trans. Distrib. 143(1), 33–38 (1996)
M.H. Haque, A general load flow method for distribution systems. Electr. Power Syst. Res. 54(1), 47–54 (2000)
S. Ghosh, D. Das, Method for load-flow solution of radial distribution networks. IEE Proc. Gener. Trans. Distrib. 146(6), 641–648 (1999)
The MATLAB by Mathworks Corporation, MATLAB version 7.8 (2009)
V.V.S.N. Murthy, A. Kumar, Mesh distribution system analysis in presence of distributed generation with time varying load model. Electr. Power Energy Syst. 62, 836–854 (2014)
A. Jain, A.R. Gupta, A. Kumar, An efficient method for D-STATCOM placement in radial distribution system, in Sixth IEEE India International Conference on Power Electronics. (2014), pp. 1–6. doi:10.1109/IICPE.2014.7115746
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Gupta, A.R., Kumar, A. Performance Analysis of Radial Distribution Systems with UPQC and D-STATCOM. J. Inst. Eng. India Ser. B 98, 415–422 (2017). https://doi.org/10.1007/s40031-016-0254-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40031-016-0254-4