Skip to main content
SpringerLink
Log in

Effect of Welding Heat Input on Microstructure and Mechanical Properties of HSLA Steel Joint

  • Technical Article
  • Published:
Metallography, Microstructure, and Analysis Aims and scope Submit manuscript

Abstract

Gas tungsten arc welding of HSLA steel was conducted with different welding heat inputs, and the influences of welding heat input on the microstructure, Vickers hardness, and impact toughness of heat-affected zone (HAZ) in prepared joints were systematically investigated. The microstructure in HAZ with low welding heat input mainly consisted of martensite, and the microhardness of coarse grain HAZ was measured higher than that of fine grain zone. The results show that increasing the welding heat input could suppress the formation of martensite and reduce the microhardness of HAZ. However, the impact toughness of HAZ was not monotonously improved with the increase of welding heat input. It is deemed that the coarsened grain, the formation of upper bainite, and the non-uniform distribution of carbides and inclusions in HAZ could degrade the impact toughness. Tests demonstrate that the optimum comprehensive properties of HAZ were obtained when the welding heat input was 0.67 kJ/mm.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9

Similar content being viewed by others

References

  1. Q. Xue, D. Benson, M.A. Meyers, V.F. Nesterenko, E.A. Olevsky, Constitutive response of welded HSLA 100 steel. Mater. Sci. Eng. A 354(1–2), 166–179 (2003) (in English)

    Article  Google Scholar 

  2. D.M. Viano, N.U. Ahmed, G.O. Schumann, Influence of heat input and travel speed on microstructure and mechanical properties of double tandem submerged arc high strength low alloy steel weldments. Sci. Technol. Weld. Join. 5(1), 26–34 (2000) (in English)

    Article  Google Scholar 

  3. Y. Li, D.N. Crowther, M.J.W. Green, P.S. Mitchell, T.N. Baker, The effect of vanadium and niobium on the properties and microstructure of the intercritically reheated coarse grained heat affected zone in low carbon microalloyed steels. Iron Steel Inst. Jpn. Int. 41(1), 46–55 (2001) (in English)

    Article  Google Scholar 

  4. M. Shome, Effect of heat-input on austenite grain size in the heat-affected zone of HSLA-100 steel. Mater. Sci. Eng. A 445–446(2), 454–460 (2007) (in English)

    Article  Google Scholar 

  5. G. Spanos, D.W. Moon, R.W. Fonda, E.S.K. Menon, A.G. Fox, Microstructural, compositional, and microhardness variations across a gas-metal arc weldment made with an ultralow-carbon consumable. Metall. Mater. Trans. A 32(12), 3043–3054 (2001) (in English)

    Article  Google Scholar 

  6. M. Shome, O.N. Mohanty, Continuous cooling transformation diagrams applicable to the heat-affected zone of HSLA-80 and HSLA-100 steels. Metall. Mater. Trans. A 37(7), 2159–2169 (2006) (in English)

    Article  Google Scholar 

  7. S. Morito, H. Yoshida, T. Maki, X. Huang, Effect of block size on the strength of lath martensite in low carbon steels. Mater. Sci. Eng. A 438–440(11), 237–240 (2006) (in English)

    Article  Google Scholar 

  8. S.K. Dhua, D. Mukerjee, D.S. Sarma, Weldability and microstructural aspects of shielded metal arc welded HSLA-100 steel plates. Iron Steel Inst. Jpn. Int 42(3), 290–298 (2002) (in English)

    Article  Google Scholar 

  9. M. Mukherjee, T.K. Pal, Influence of heat input on martensite formation and impact property of ferritic–austenitic dissimilar weld metals. J. Mater. Sci. Technol. 28(4), 343–352 (2012) (in English)

    Article  Google Scholar 

  10. J.C. Ion, K.E. Easterling, M.F. Ashby, A second report on diagrams of microstructure and hardness for heat-affected zones in welds. Acta Metall. 32(11), 1949–1962 (1984) (in English)

    Article  Google Scholar 

  11. H.K.D.H. Bhadeshia, L.E. Svensson, B.A. Gretoft, Model for the development of microstructure in low-alloy steel (Fe–Mn–Si–C) weld deposits. Acta Metall. 33(7), 1271–1283 (1985) (in English)

    Article  Google Scholar 

  12. Y.Q. Zhang, H.Q. Zhang, J.F. Li, W.M. Liu, Effect of heat input on microstructure and toughness of coarse grain heat affected zone in Nb microalloyed HSLA steels. J. Iron. Steel Res. Int. 16(5), 73–80 (2009) (in English)

    Article  Google Scholar 

  13. S.S. Babu, The mechanism of acicular ferrite in weld deposits. Curr. Opin. Solid State Mater. Sci. 8(3–4), 267–278 (2004) (in English)

    Article  Google Scholar 

  14. L.Y. Lan, C.L. Qiu, D.W. Zhao, X.H. Gao, L.X. Du, Effect of single pass welding heat input on microstructure and hardness of submerged arc welded high strength low carbon bainitic steel. Sci. Technol. Weld. Join. 17(7), 564–570 (2012) (in English)

    Article  Google Scholar 

  15. S.D. Bhole, J.B. Nemade, L. Collins, C. Liu, Effect of nickel and molybdenum additions on weld metal toughness in a submerged arc welded HSLA line-pipe steel. J. Mater. Process. Technol. 173(1), 92–100 (2006) (in English)

    Article  Google Scholar 

  16. P.L. Harrison, R.A. Farrar, Influence of oxygen-rich inclusions on the γ → α phase transformation in high-strength low-alloy (HSLA) steel weld metals. J. Mater. Sci. 16(8), 2218–2226 (1981) (in English)

    Article  Google Scholar 

  17. S.A.A.A. Mousavi, R. Miresmaeili, Experimental and numerical analyses of residual stress distributions in TIG welding process for 304L stainless steel. J. Mater. Process. Technol. 208(1–3), 383–394 (2008) (in English)

    Article  Google Scholar 

  18. O. Grong, D.K. Matlock, Microstructural development in mild and low-alloy steel weld metals. Int. Mater. Rev. 31(1), 27–48 (1986) (in English)

    Article  Google Scholar 

  19. M. Shome, O.P. Gupta, O.N. Mohanty, Effect of simulated thermal cycles on the microstructure of the heat-affected zone in HSLA-80 and HSLA-100 steel plates. Metall. Mater. Trans. A 35(3), 985–996 (2004) (in English)

    Article  Google Scholar 

  20. G. Thewlis, Weldability of X100 linepipe. Sci. Technol. Weld. Join. 5(6), 365–377 (2000) (in English)

    Article  Google Scholar 

  21. G. Thewlis, Classification and quantification of microstructures in steels. Mater. Sci. Technol. 20(2), 143–160 (2004) (in English)

    Article  Google Scholar 

  22. S. Talas, The assessment of carbon equivalent formulas in predicting the properties of steel weld metals. Mater. Des. 31(5), 2649–2653 (2010) (in English)

    Article  Google Scholar 

  23. B. Arivazhagan, G. Srinivasan, S.K. Albert, A.K. Bhaduri, A study on influence of heat input variation on microstructure of reduced activation ferritic martensitic steel weld metal produced by GTAW process. Fusion Eng. Des. 86(2–3), 192–197 (2011) (in English)

    Article  Google Scholar 

  24. E. Gharibshahiyan, A.H. Raouf, N. Parvin, M. Rahimian, The effect of microstructure on hardness and toughness of low carbon welded steel using inert gas welding. Mater. Des. 32(4), 2042–2048 (2011) (in English)

    Article  Google Scholar 

  25. T. Mohandas, G. Madhusudan Reddy, B. Satish Kumar, Heat-affected zone softening in high-strength low-alloy steels. J. Mater. Process. Technol. 88(1–3), 284–294 (1999) (in English)

    Article  Google Scholar 

  26. K. Abbaszadeh, H. Saghafian, S. Kheirandish, Effect of bainite morphology on mechanical properties of the mixed bainite–martensite microstructure in D6AC steel. J. Mater. Sci. Technol. 28(4), 336–342 (2012) (in English)

    Article  Google Scholar 

Download references

Acknowledgments

This work was financially supported by the National Key Basic Research and Development Program of China (Grant No. 2011CB013402), the National Natural Science Foundation of China (Grant No. 51374048), and the Fundamental Research Funds for the Central Universities (Grant No. DUT13ZD209).

Author information

Authors and Affiliations

  1. School of Materials Science and Engineering, Dalian University of Technology, Dalian, 116085, People’s Republic of China

    Honggang Dong, Xiaohu Hao & Dewei Deng

Authors
  1. Honggang Dong
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Xiaohu Hao
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Dewei Deng
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Honggang Dong.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Dong, H., Hao, X. & Deng, D. Effect of Welding Heat Input on Microstructure and Mechanical Properties of HSLA Steel Joint. Metallogr. Microstruct. Anal. 3, 138–146 (2014). https://doi.org/10.1007/s13632-014-0130-z

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s13632-014-0130-z

Keywords

Search

Navigation