Abstract
In this article, the use of chromium (Cr) as a grain refiner for a CuAlBe shape memory alloy is discussed. Alloys with 0.1, 0.2, 0.3, and 0.5 wt.% Cr were characterized by optical microscopy, scanning electron microscope, and x-ray diffraction. Also, the influence of the different percentages of Cr on the grain size and on the mechanical properties was analyzed through macro- and microscopic evaluations and by tensile and hardness tests, respectively. Finally, the phase transformation temperatures of the alloys were determined by thermal analysis using differential scanning calorimetry. The results showed that the higher the Cr content, the greater the grain refinement effect and lower the hardness. In addition, at room temperature the alloys with 0.1 and 0.2 wt.% Cr were austenitic, while the rest were martensitic. The tensile tests showed that the alloy with 0.2 wt.% Cr provided the best strain-stress performance. The conclusion was that the use of 0.2 wt.% Cr as a grain refiner improved the mechanical properties of the CuAlBe alloy; however, the same was not observed for the other Cr contents.
Similar content being viewed by others
References
Y. Zhu and G. Dui, Influence of Magnetization Rotation on Martensite Reorientation in Magnetic Shape Memory Alloy, Acta Mech. Solida Sin., 2010, 23, p 13–19
E.A. Williams, G. Shaw, and M. Elahinia, Control of an Automotive Shape Memory Alloy Mirror Actuator, Mechatronics, 2010, 20, p 527–534
D. Vojtěch, M. Voděrová, J. Kubásek, P. Novák, P. Šedá, A. Michalcová, J. Fojt, J. Hanuš, and O. Mestek, Effects of Short-Time Heat Treatment and Subsequent Chemical Surface Treatment on the Mechanical Properties, Low-Cycle Fatigue Behavior and Corrosion Resistance of a Ni-Ti (50.9 at.% Ni) Biomedical Alloy Wire Used for the Manufacture of Stents, Mater. Sci. Eng. A, 2011, 528, p 1864–1876
V.H.C. Albuquerque, T.A.A. Melo, R.M. Gomes, S.J.G. Lima, and J.M.R.S. Tavares, Grain size and Temperature Influence on the Toughness of a CuAlBe Shape Memory Alloy, Mater. Sci. Eng. A, 2010, 528, p 459–466
K. Otsuka and C.M. Wayman, Shape Memory Materials, Cambridge University Press, Cambridge, 1998
M.H. Wu, L.M. Schetky, Industrial Applications for Shape Memory Alloys, Proceedings of the International Conference on Shape Memory and Superelastic Technologies, Pacific Grove, California, 2000, p 171–182
S. Belkahla, H.F. Zuñiga, and G. Guenin, Elaboration and Characterization of New Low Temperature Shape Memory Cu-Al-Be Alloys, Mater. Sci. Eng. A, 1993, 169, p 119–124
Q.Y. Wang, Y.F. Zheng, and Y. Liu, Microstructure, Martensitic Transformation and Superelasticity of Ti49.6Ni45.1Cu5Cr0.3 Shape Memory Alloy, Mater. Lett., 2011, 65, p 74–77
Y. Sutou, T. Omori, N. Koeda, R. Kainuma, and K. Ishida, Effects of Grain Size and Texture on Damping Properties of Cu-Al-Mn-Based Shape Memory Alloys, Mater. Sci. Eng. A, 2006, 438, p 743–746
S. Montecinos, A. Cuniberti, and R. Romero, Effect of Grain Size on the Stress-Temperature Relationship in a β CuAlBe Shape Memory Alloy, Intermetallics, 2011, 19, p 35–38
B.S. Murty, S.A. Kori, and M. Chakraborty, Grain Refinement of Aluminium and its Alloys by Heterogeneous Nucleation and Alloying, Int. Mater. Rev., 2002, 47, p 3–29
P. Zhang, A. Ma, S. Lu, G. Liu, P. Lin, J. Jiang, and C. Chu, Effect of Grain Refinement on the Mechanical Properties of Cu-Al-Be-B Shape Memory Alloy, Mater. Des., 2011, 32, p 348–352
P. Zhang, A. Ma, J. Jiang, S. Lu, P. Lin, D. Yang, and G. Liu, Microstructural Evolution and Mechanical Response of Cu-Al-Be-B Shape Memory Alloy Processed by Repetitive Equal Channel Angular Pressing, J. Alloys Compd., 2010, 497, p 210–214
V.H.C. Albuquerque, T.A.A. Melo, D.F. Oliveira, R.M. Gomes, and J.M.R.S. Tavares, Evaluation of Grain Refiners Influence on the Mechanical Properties in a CuAlBe Shape Memory Alloy by Ultrasonic and Mechanical Tensile Testing, Mater. Des., 2010, 31, p 3275–3281
R. Araya, M. Marivil, C. Mir, O. Moroni, and A. Sepúlveda, Temperature and Grain Size Effects on the Behavior of CuAlBe SMA Wires Under Cyclic Loading, Mater. Sci. Eng. A, 2008, 496, p 209–213
D.N. Adnyana, Effect of Grain Size on Transformation Temperatures in a Grain-Refined, Copper-Based, Shape-Memory Alloy, Metallography, 1986, 19, p 187–196
T. Shanmugasundaram, M. Heilmaier, B.S. Murty, and V.S. Sarma, On the Hall-Petch Relationship in a Nanostructured Al-Cu Alloy, Mater. Sci. Eng. A, 2010, 527, p 7821–7825
G.-S. Yang, J.-K. Lee, and W.-Y. Jang, Effect of Grain Refinement on Phase Transformation Behavior and Mechanical Properties of Cu-Based Alloy, Trans. Nonferrous Met. Soc. China, 2009, 19(4), p 979–983
A.C.R. Veloso, D.F. Oliveira, M.Q. Silva, R.M. Gomes, S.J.G. Lima, and T.A.A. Melo, Microstructural Investigation of Cu-Al-Ni-Nb Alloys at Low Temperature, 10th InterAmerican Congress of Electron Microscopy 2009, CIASEM 2009, Section M-MA: Metallic Alloys I, October 25–28, Rosario City, Argentina, 2009
G.A. Lara-Rodriguez, G. Gonzalez, H. Flores-Zúñiga, and J. Cortés-Pérez, The Effect of Rapid Solidification and Grain Size on the Transformation Temperatures of Cu-Al-Be Melt Spun Alloys, Mater. Charact., 2006, 57, p 154–159
H. Funakubo, Shape Memory Alloys, Gordon and Breach Science Publishers, London, 1987
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
da M. Candido, G.V., de A. Melo, T.A., De Albuquerque, V.H.C. et al. Characterization of a CuAlBe Alloy with Different Cr Contents. J. of Materi Eng and Perform 21, 2398–2406 (2012). https://doi.org/10.1007/s11665-012-0159-6
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-012-0159-6