Skip to main content

Advertisement

SpringerLink
Log in

Tribological Properties of SiC-Reinforced Basalt-Based Coatings

  • Original Paper
  • Published:
Tribology Letters Aims and scope Submit manuscript

Abstract

In the current study, the wear behaviour of basalt-based glass and glass–ceramic coatings was investigated. SiC-reinforced basalt-based powders were coated by an atmospheric plasma spray process and evaluated using the ball-on-disk wear test. X-ray diffraction analysis, scanning electron microscopy, and optical microscopy were employed for characterisation. The friction coefficients of the basalt-based glass and glass–ceramic coatings ranged from 0.38 to 0.55 and from 0.12 to 0.70, respectively, depending on the wear condition and SiC content. The wear test results show that SiC addition has a positive effect on the wear resistance of the glass and glass–ceramic coatings.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16

Similar content being viewed by others

References

  1. Wielage, B., Steinhäuser, S., Schnick, T., Nickelmann, D.: Characterization of the wear behavior of thermal sprayed coatings. J. Therm. Spray. Tech. 8, 553–558 (1998)

    Article  Google Scholar 

  2. Yılmaz, S., Bayrak, G., Sen, S., Sen, U.: Structural characterization of basalt-based glass–ceramic coatings. Mat. Des. 27, 1092–1096 (2006)

    Article  Google Scholar 

  3. Bobkova, N.M., Barantseva, S.E., Kononovich, V.M.: Synthesis of wear-resistant ceramics. Glass Ceram. 59(11–12), 371–373 (2002)

    Article  Google Scholar 

  4. Herman, D., Okupski, T., Walkowiak, W.: Wear resistance glass–ceramics with a gahnite phase obtained in CaO–MgO–ZnO–Al2O3–B2O3–SiO2 system. J. Eur. Ceram. Soc. 31, 485–492 (2011)

    Article  Google Scholar 

  5. Asi, I., Shalabi, F., Naji, J.: Use of basalt in asphalt concrete mixes. Cons. Build. Mat. 23, 498–506 (2009)

    Article  Google Scholar 

  6. Ibrahim, K.M., Tarawneh, K., Rabba, I.: Phases of activity and geochemistry of basaltic dike systems in northeast Jordan parallel to the Red Sea. J. Asia. Earth. Sci. 21, 467–472 (2003)

    Article  Google Scholar 

  7. Khater, G.A., Abdel-Motelib, A., El Manawi, A.W., Abu Safiah, M.O.: Glass–ceramics materials from basaltic rocks and some industrial waste. J. Non Crystal. Solid. 358, 1128–1134 (2012)

  8. Ercenk, E., Sen, U., Yilmaz, S.: The effect of SiC addition on the crystallization kinetics of atmospheric plasma–sprayed basalt-based coatings. Ceram. Int. 38, 6549–6556 (2012)

    Article  Google Scholar 

  9. Lin, M.T., Jiang, D.Y., Li, L., Lu, Z.L., Lai, T.R., Shi, J.L.: The effect of creep deformation of a β sialon on Vickers hardness, fracture toughness and Weibull modulus. Mat. Sci. Eng. A 351, 9–14 (2003)

    Article  Google Scholar 

  10. Gunay, V., Hampshire, S.: Processing and properties of pressureless-sintered Si3N4–SiC composites. J. Mat. Pro. Tech. 54, 348–354 (1996)

    Article  Google Scholar 

  11. Mirsaneh, M., Reaney, I.M., Hatton, P.V., James, P.F.: Characterization of high-fracture toughness K-fluorrichterite–fluorapatite glass ceramics. J. Am. Ceram. Soc. 87(2), 240–246 (2004)

    Article  Google Scholar 

  12. Evans, A.G., Charles, E.A.: Fracture toughness determinations by indentation. J. Am. Ceram. Soc. 59(7–8), 371–372 (1976)

    Article  Google Scholar 

  13. Boch, P., Niepce, J.C. (eds.): Ceramic Materials, Processes, Properties and Applications. ISTE, London (2007)

    Google Scholar 

  14. Kanchanarat, N., Bandyopadhyay-Ghosh, S., Reaney, I.M., Brook, I.M., Hatton, P.V.: Microstructure and mechanical properties of fluorcanasite glass–ceramics for biomedical applications. J. Mater. Sci. 43, 759–765 (2008)

    Article  Google Scholar 

  15. Monmaturapoj, N., Lawita, P., Thepsuwan, W.: Characterisation and properties of lithium disilicate glass ceramics in the SiO2–Li2O–K2O–Al2O3 system for dental applications. Adv. Mat. Sci. Eng. 2013, 11 pp (2013)

  16. Kamardan, M.G., Zaidi, N.H.A., Dalimin, M.N., Zaidi, A.M.A., Jamaludin, S.B., Jamil, M.M.A.: The sintering temperature effect on the shrinkage behavior of cobalt chromium alloy. Am. J. Appl. Sci. 7(11), 1443–1448 (2010)

    Article  Google Scholar 

  17. ASTM C-20: Standard Test Methods for Apparent Porosity, Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned Refractory Brick and Shapes by Boiling Water. ASTM, West Conshohocken (2000)

    Google Scholar 

  18. Alomayri, T., Shaikh, F.U.A., Low, I.M.: Thermal and mechanical properties of cotton fabric-reinforced geopolymer composites. J. Mat. Sci 48, 6746–6752 (2013)

    Article  Google Scholar 

  19. Barbieri, L., Corradi, A., Lancellotti, I.: Bulk and sintered glass–ceramics by recycling municipal incinerator bottom ash. J. Eur. Ceram. Soc. 20, 1637–1643 (2000)

    Article  Google Scholar 

  20. Sun, H.Q., Shi, Y.N., Zhang, M.X.: Sliding wear-induced microstructure evolution of nanocrystalline and coarse-grained AZ91D Mg alloy. Wear 266, 666–670 (2009)

    Article  Google Scholar 

  21. Ercenk, E., Sen, U., Yilmaz, S.: Structural characterization of plasma sprayed basalt–SiC glass–ceramic coatings. Ceram. Int. 37, 883–889 (2011)

    Article  Google Scholar 

  22. Jafarzadeh, K., Zalefi, Z., Ghavidel, B.: The effect of plasma spray parameters on the cavitation erosion of Al2O3–TiO2 coatings. Surf. Coat. Tech. 205, 1850–1855 (2010)

    Article  Google Scholar 

  23. Brossard, S., Munroe, P.R., Tran, A.T.T., Hyland, M.M.: Study of the splat formation for plasma sprayed NiCr on aluminum substrate as a function of substrate condition. Surf. Coat. Tech. 204, 2647–2656 (2010)

    Article  Google Scholar 

  24. Sabiruddin, K., Bandyopadyay, P.P., Bolelli, G., Lusvarghi, L.: Variation of splat shape with processing conditions in plasma sprayed alumina coatings. J. Mat. Process. Tech. 211, 450–462 (2011)

    Article  Google Scholar 

  25. Karamanov, A., Pelino, M.: Evaluation of the degree of crystallisation in glass–ceramics by density measurements. J. Eur. Ceram. Soc. 19, 649–654 (1999)

    Article  Google Scholar 

  26. Bartuli, C., Lusvarghi, L., Manfredini, T., Valente, T.: Thermal spraying to coat traditional ceramic substrates: case studies. J. Eur. Ceram. Soc. 27, 1615–1622 (2007)

    Article  Google Scholar 

  27. Khater, G.A.: Glass–ceramics in the CaO–MgO–Al2O3–SiO2 system based on industrial waste materials. Jur. Non Crytal. Solid. 356, 3066–3070 (2010)

    Article  Google Scholar 

  28. Rawlings, R.D., Wu, J.P., Boccacini, A.R.: Glass–ceramics: their production from wastes—a review. J. Mat. Sci. 41, 733–761 (2006)

    Article  Google Scholar 

  29. Erol, M., Kucukbayrak, S., Ersoy-Mericboyu, A.: Production of glass–ceramics obtained from industrial wastes by means of controlled nucleation and crystallization. Chem. Eng. J. 132, 335–343 (2007)

    Article  Google Scholar 

  30. Bolelli, G., Cannillo, V., Lusvarghi, L., Manfredini, T., Siligardi, C., Bartuli, C., Loreto, A., Valente, T.: Plasma-sprayed glass–ceramic coatings on ceramic tiles: microstructure, chemical resistance and mechanical properties. J. Eur. Ceram. Soc. 25, 1835–1853 (2005)

    Article  Google Scholar 

  31. Ercenk, E., Sen, U., Yilmaz, S.: The erosive wear behavior of basalt based glass and glass–ceramic coatings. Tribo. Int. 52, 94–100 (2012)

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Metallurgical and Materials Engineering, Engineering Faculty, Sakarya University, Esentepe Campus, 54187, Sakarya, Turkey

    Ediz Ercenk, Ugur Sen & Senol Yilmaz

Authors
  1. Ediz Ercenk
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Ugur Sen
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Senol Yilmaz
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Ediz Ercenk.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Ercenk, E., Sen, U. & Yilmaz, S. Tribological Properties of SiC-Reinforced Basalt-Based Coatings. Tribol Lett 56, 337–354 (2014). https://doi.org/10.1007/s11249-014-0413-1

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11249-014-0413-1

Keywords

Search

Navigation