Abstract
Al2O3–ZrO2 coatings were deposited using a vacuum arc deposition system equipped with two co-planar cathodes. The plasma was injected into a cylindrical magnetic duct through annular anode apertures toward a substrate or an electrostatic ion current probe positioned on the duct axis, in vacuum and in a low-pressure oxygen or argon + oxygen background. Ion current and arc voltage measurements and visual observation of the cathode spots were used to find stable arcing conditions, using a straight plasma duct configuration. The cathode spot operation and transport of the plasma beam in the duct were studied as a function of arc current (I arc = 25–200 A) and oxygen or oxygen + argon pressures (P = 0.1–1.5 Pa). Coatings were fabricated by exposing Si or WC–Co substrates simultaneously to Al and Zr plasmas using a 1/8 torus filter configuration in O2 + Ar pressures. The coating composition, structure, microhardness, adhesion, and wear behavior were studied as functions of the deposition parameters. Favorable conditions for stable arcing were obtained with I arc = 75 and 100 A for Al and Zr plasmas, respectively. The ion current decreased, and the arc voltage increased with the oxygen pressure. Behavior of the ion current and arc voltage suggested that cathode poisoning started at P = 0.5 Pa. Deposition rates were 0.3-0.6 μm/min, depending on the substrate position. All coatings were “Zr rich”, i.e., the Zr:Al ratio was in the range of 1.2–5.6 depending on the substrate position and deposition conditions. The coatings with higher ZrO2 concentration were harder and had better resistance to wear. The coating’s hardness reached a maximum of ~22–24 GPa at a deposition temperature of 500 °C or a negative bias voltage of 75–100 V.
Similar content being viewed by others
References
Klocke F, Gerschwiler K, Fritsch R, Lung D (2006) Surf Coat Technol 201:4389
Holleck H (1986) J Vac Sci Technol A4:2661
Knotek O, Löffler F, Krämer G (2001) In: Bunshah R (ed) Handbook of hard coatings deposition technologies, properties and applications. Noyes Publications, New Jersy, p 370
Chaim R, Zhitomirsky I, Gal-Or L, Bestgen H (1997) J Mater Sci 32:389. doi:10.1023/A:1018505517104
Kim HJ, Kim YJ (1999) J Mater Sci 34:29. doi:10.1023/A:1004492919174
Shanmugavelayutham G, Yano S, Kobayashi A (2006) Vacuum 80:1336
Sharafat S, Kobayashi A, Ogden V, Ghoniem MN (2000) Vacuum 59:185
Leushake U, Krell T, Schulz U, Peters M, Kaysser WA, Rabin BH (1997) Surf Coat Technol 94–95:131
Teixeira V, Monteiro A, Duarte J, Portinha A (2002) Vacuum 67:477
Klostermann H, Böcher B, Fietzke F, Modes T, Zywitzki O (2005) Surf Coat Technol 200:760
Trinh DH, Högberg H, Andersson JM, Collin M, Reineck I, Helmersson U, Hultman L (2006) J Vac Sci Technol A24:309
Matthews L, Rawlings RD (1994) Composite materials: engineering and science. Chapman and Hall, Oxford, p 137
Tay BK, Zhao ZW, Chua DHC (2006) Mater Sci Eng R52:1
Jerebtsov DA, Mikhailov GG, Sverdina SV (2000) Ceram Int 26:821
Raveh A, Zukerman I, Shneck R, Avni R, Fried I (2007) Surf Coat Technol 201:6136
Qadri SB, Gilmore CM, Quinn C, Skelton EF, Gosset CR (1989) Phys Rev B39:6234
Aita CR, Scanlan CM, Gajdardziska-Josifovska M (1994) JOM 46:40
Trinh DH, Ottosson M, Collin M, Reineck I, Hultman L, Hogberg H (2008) Thin Solid Films 516:4977
Trinh DH, Kubart T, Nyberg T, Ottosson M, Hultman L, Hogberg H (2008) Thin Solid Films 516:8352
Brill R, Koch F, Mazurelle J, Levchuk D, Balden M, Yamada-Takamura Y, Maier H, Bolt H (2003) Surf Coat Technol 174–175:606
Rosen J, Mraz S, Kreissig U, Music D, Schneider JM (2005) Plasma Chem Plasma Proc 25:303
Yu GO, Tay BK, Zhao ZW (2005) Appl Phys A81:405
Kim SK, Le VV, Boxman RL, Zhitomirsky VN, Lee JY (2010) Surf Coat Technol 204:1697
Ben-Ami R, Zhitomirsky VN, Boxman RL, Goldsmith S (1999) Plasma Sour Sci Technol 8:355
Zhitomirsky VN, Grimberg I, Boxman RL, Weiss BZ, Travitzky NA, Goldsmith S (1997) Surf Coat Technol 94–95:207
Zhitomirsky VN, Grimberg I, Rapoport L, Travitzky NA, Boxman RL, Goldsmith S, Weiss BZ (1999) Surf CoatTechnol 120–121:219
Zhitomirsky VN (2007) Surf Coat Technol 201:6122
Boxman RL, Zhitomirsky VN (2006) Rev Sci Instrum 77:021101
Zhitomirsky VN, Raveh A, Boxman RL, Goldsmith S (2009) IEEE Trans Plasma Sci 37:1517
Zhitomirsky VN, Boxman RL, Goldsmith S (2004) Surf Coat Technol 188–189:220
Zhitomirsky VN, Grimberg I, Rapoport L, Boxman RL, Travitzky NA, Goldsmith S, Weiss BZ (2000) Surf Coat Technol 133–134:114
Holmberg K, Mattews A (1994) In: Dowson D (ed) Coatings tribology, tribology series 28, 1st edn. Elsevier, Oxford, p 53
Zhitomirsky VN, Kim SK, Burstein L, Boxman RL (2010) Appl Surf Sci (in press)
Hofmann S, Sanz JM (1982) J Trace Microprobe Tech 1:213
Zhitomirsky VN, Zarchin O, Wang SG, Boxman RL, Goldsmith S (2001) IEEE Trans Plasma Sci 29:776
Zhitomirsky VN, Boxman RL, Goldsmith S (1995) J Vac Sci Technol A13:2233
Zhitomirsky VN, Kinrot U, Alterkop B, Boxman RL, Goldsmith S (1996) Surf Coat Technol 86–87:263
Rosen J, Persson POA, Ionescu M, Pigott J, McKenzie DR, Bilek MMM (2007) Plasma Chem Plasma Proc 27:599
Bolt H, Koch F, Rodet JL, Karpov D, Menzel S (1999) Surf Coat Technol 116–119:956
Niu EW, Li L, Lv GH, Chen H, Li XZ, Feng WR, Fan SH, Yang SZ, Yang XZ (2007) Mater Sci Eng A460:135
Niu EW, Li L, Lv GH, Chen H, Li XZ, Fan SH, Yang SZ, Yang XZ (2008) Appl Surf Sci 254:3909
Mattox MD (2000) Surf Coat Technol 133–134:517
Shtansky DV, Kaneko K, Ikuhara Y, Levashov EA (2001) Surf Coat Technol 148:206
Acknowledgements
The authors gratefully acknowledge the funding support provided by the Science Ministries of Israel and Korea, Mr. M. Govberg for his engineering assistance, Dr. Y. Rosenberg for the XRD analysis, and Dr. L. Burshtein for XPS studies. The assistant of Dr. Y. Shneor, Rotem Industries Ltd., in the scratch and wear experiments, is gratefully acknowledged.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Zukerman, I., Zhitomirsky, V.N., Beit-Ya’akov, G. et al. Vacuum arc deposition of Al2O3–ZrO2 coatings: arc behavior and coating characteristics. J Mater Sci 45, 6379–6388 (2010). https://doi.org/10.1007/s10853-010-4734-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10853-010-4734-7