Skip to main content
SpringerLink
Log in

Thermal Characterization of Electrical Wires and Insulation Operated in Variable Frequency Mode

  • Published:
Fire Technology Aims and scope Submit manuscript

Abstract

NFPA 70 provides guidelines on conducting wire size rating for different service current ratings. Additionally, an engineering calculation method is provided for unusual cases. While not apparent, these guidelines are valid only for 60 Hz type frequencies. Electrical conductors have increased Joule heating with higher frequency operation because of electromagnetic effects like skin and proximity effects and the increase of total reactance of conductors and appliances. Until now, those effects have not been a fire safety concern, but the large increase in high power applications using frequencies higher than 60 Hz in variable frequency drives, also called adjustable frequency drives or simply “AC drives”, to control the operation of large motors, changes this. While research has improved the performance of motors and AC drives, there has been relatively little research on the thermal effects and fire safety implications of these systems. In this paper we show that conductors used with common variable frequency power electronics have heat dissipation rates that can be up to 50% larger than what is calculated according to the standard formulas used for 60 Hz systems. Using accelerated aging models for the wire insulation it is shown that these increases in heat dissipation rate can reduce useful cable life by a factor of two or more.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7

Similar content being viewed by others

References

  1. Hall JR, Cote AE (2008) An overview of the fire problem and fire protection. In: NFPA (ed) Fire protection handbook. National Fire Protection Association, Quincy

    Google Scholar 

  2. Landis FH (2007) Electric arc hazard. Prof Saf 52:18

    Google Scholar 

  3. Gammon T, Matthews J (2008) IEEE 1584–2002 arc modeling debate. IEEE Ind Appl Mag 14:61–69

    Article  Google Scholar 

  4. Béland B (1981) Arcing phenomenon as related to fire investigation. Fire Technol 17:189–201. doi:10.1007/BF02473096

    Article  Google Scholar 

  5. Lee DA, Trotta AM, King WH Jr (2000) New technology for preventing residential electrical fires: arc-fault circuit interrupters (AFCIS). Fire Technol 36:145–162. doi:10.1023/A:1015410726786

    Article  Google Scholar 

  6. Earley MW, Sargent JS, Coache CD, Roux R (2011) National electrical code handbook. National Fire Protection Association, Quincy

    Google Scholar 

  7. Neher JH, McGrath MH (1957) The calculation of the temperature rise and load capability of cable systems. AIEE Trans 76:752–772

    Google Scholar 

  8. Anders George J (1997) Rating of electric power cables. McGraw Hill, New York

    Google Scholar 

  9. Hiranandani A (1991) Calculation of conductor temperatures and ampacities of cable systems using a generalized finite difference model. IEEE Trans Power Deliv 6:15–24

    Article  Google Scholar 

  10. Hwang CC, Chang JJ, Chen HY (2000) Calculation of ampacities for cables in trays using finite elements. Electr Power Syst Res 54:75–81

    Article  Google Scholar 

  11. Liang Y (2012) Steady-state thermal analysis of power cable systems in ducts using streamline-upwind/petrov-galerkin finite element method. IEEE Trans Dielectr Electr Insul 19:283–290

    Article  Google Scholar 

  12. Mahmoudi A, Kahourzade S, Lee DSS (2011) Cable ampacity calculation in heterogenous soil using finite element analysis. In: 5th International Power Engineering and Optimization Conference (PEOCO), 2011, pp 416–421, Shah Alam, Selangor. Institute of Electrical and Electronics Engineers

  13. Cardenas-Estrada Dorindo E (2012) The thermal electrical overheating. A physicochemical perspective of the electrical warming. Revista Facultad de Ingeniera 64:57–67

    Google Scholar 

  14. Kuznetskii RS (1975) Temperature-dependent resistivity of a flat conductor and the temperature, current, and electric field patterns. J Eng Phys 29:1194–1195

    Article  Google Scholar 

  15. Quinton AR (1980) The variation of resistance with temperature. Phys Teach 18:213

    Article  Google Scholar 

  16. Saint-Sulpice L, Lakrit M, Chirani SA, Calloch S (2014) Variation in electric resistivity in metastable alloys during thermomechanical loading: effects of temperature, elasticity, plasticity and phase transformation. Mech Mater 71:1–9

    Article  Google Scholar 

  17. Dimitraki NS, Dimitraki SN (2008) Measurement of a conductor cross sectional area. Surf Eng Appl Electrochem 44:69–72

    Article  Google Scholar 

  18. Acero J, Sullivan CR (2013) A dynamic equivalent network model of the skin effect. In: Applied Power Electronics Conference and Exposition (APEC), 2013 Twenty-Eighth Annual IEEE, pp 2392–2397, Long Beach, CA, USA. Institute of Electrical and Electronics Engineers

  19. Coperich KM, Ruehli AE, Cangellaris A (2000) Enhanced skin effect for partial-element equivalent-circuit (PEEC) models. IEEE Trans Microwave Theory Tech 48:1435–1442

    Article  Google Scholar 

  20. Yen C-S, Fazarinc Z, Wheeler RL (1982) Time-domain skin-effect model for transient analysis of lossy transmission lines. Proc IEEE 70:750–757

    Article  Google Scholar 

  21. Huffman HH (1990) Introduction to solid-state adjustable speed drives. IEEE Trans Ind Appl 76:671–678

    Article  Google Scholar 

  22. Leonhard W (1988) Adjustable-speed AC drives. Proc IEEE 76:455–471

    Article  Google Scholar 

  23. Blaabjerg F, Thoegersen P (2004) Adjustable speed drives—future challenges and applications. In: The 4th International Power Electronics and Motion Control Conference, 2004. IPEMC 2004, vol 1, pp 36–45. Institute of Electrical and Electronics Engineers, Xi’an

  24. Diaz A, Saltares R, Rodriguez C, Nuez RF, Ortiz-Rivera EI, Gonzalez-Llorente J (2009) Induction motor equivalent circuit for dynamic simulation. In: IEEE International Electric Machines and Drives Conference, 2009. IEMDC ’09, pp 858–863. Institute of Electrical and Electronics Engineers, Miami

  25. Piesciorovsky EC, White WN (2010) Heat gain from adjustable speed (variable frequency) drives. ASHRAE Trans 110:608–617

    Google Scholar 

  26. Arora TG, Aware MV, Tutakne DR (2013) Insulation stress in PWM driven adjustable frequency drives. In: 10th International Conference on Electrical Engineering/Electronics, Computer, Telecommunications and Information Technology, pp 1–5. Institute of Electrical and Electronics Engineers, Krabi

  27. Cardenas-Estrada Dorindo E (2010) Propuesta de un modelo matematico para calcular el calentamiento de conductores electricos. Tecnociencia 12:71–88

    Google Scholar 

  28. Kim S, Neikirk DP (1996) Compact equivalent circuit model for the skin effect. In: Microwave Symposium Digest, 1996, IEEE MTT-S International, vol 3, pp 1815–1818. Institute of Electrical and Electronics Engineers, San Francisco

  29. Wheeler HA (1942) Formulas for the skin effect. Proc IRE 30:412–424

    Article  Google Scholar 

  30. Agamloh E (2011) Induction motor efficiency. IEEE Ind Appl Mag 17:20–28

    Article  Google Scholar 

  31. Hayt WH, Kemmerly JE, Durbin SM (2007) Engineering circuit analysis. McGraw-Hill Higher Education, Boston

    Google Scholar 

  32. Babrauskas Vytenis (2006) Mechanisms and modes for ignition of low-voltage, PVC-insulated electrotechnical products. Fire Mater 30:151–174

    Article  Google Scholar 

  33. Alvares NJ, Lipska-Quinn AE, Hasegawa HK (1983) Thermal degradation of cable and wire insulations. Behavior of polymeric materials in fire. ASTM, Philadelphia, pp 42–66

    Chapter  Google Scholar 

  34. Benes M, Placek V, Matuschek G, Kettrup AA, Gyoryova K, Emmerich WD, Balek V (2005) Lifetime simulation and thermal characterization of pvc cable insulation materials. J Therm Anal Calorim 82:761–768

    Article  Google Scholar 

  35. Gumargalieva KZ, Ivanov VB, Zaikov GE, Moiseev JuV, Pokholok TV (1996) Problems of ageing and stabilization of poly(vinyl chloride). Polym Degrad Stab 52:73–79

    Article  Google Scholar 

  36. Horvath DA, Steinman RL (2002) Microstructure assessments for determining electric cable insulation remaining life. In: Proceedings of the International Conference on Wire System Ageing, pp 99–105. NUREG/CP0179, Rockville

  37. Stricker S (1974) Thermal design of PVC-insulated heating cable. Report 74–26-K, Toronto

  38. International Electrotechnical Commission (2004) International Standard IEC 60502–1. IEC, Switzerland

    Google Scholar 

  39. du Toit Mouton H, Putzeys B (2012) Understanding the pwm nonlinearity: single-sided modulation. IEEE Trans Power Electron 27:2116–2128

    Article  Google Scholar 

  40. Colby RS, Flora DL (1990) Measured efficiency of high efficiency and standard induction motors. In: Industry Applications Society Annual Meeting, 1990, Conference Record of the 1990 IEEE, vol 1, pp 18–23. Institute of Electrical and Electronics Engineers, Seattle

Download references

Author information

Authors and Affiliations

  1. Electrical Engineering Faculty, Technological University of Panama, Campus Victor Levi Sasso, Panama, Panama

    Dorindo E. Cardenas

  2. Department of Mechanical Engineering, The University of Texas at Austin, Austin, TX, 78712, USA

    Ofodike A. Ezekoye

Authors
  1. Dorindo E. Cardenas
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Ofodike A. Ezekoye
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Dorindo E. Cardenas.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Cardenas, D.E., Ezekoye, O.A. Thermal Characterization of Electrical Wires and Insulation Operated in Variable Frequency Mode. Fire Technol 51, 1071–1092 (2015). https://doi.org/10.1007/s10694-015-0474-1

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10694-015-0474-1

Keywords

Search

Navigation