Abstract
Recently, there have been demand for aerial robotic cameras that offer a large working space, long broadcasting times, and excellent dynamic stability to broadcast live images of various sporting events. If an aerial robotic camera was to broadcast sporting events at a very high speed, the workspace was affected dominantly by external forces induced by aerodynamics. In this paper the effect of air drag forces on the aerial robotic camera was investigated at various high speeds, operating directions, and camera poses. First, the kinematics of the aerial robotic camera were derived in static equilibrium with inverse position kinematics and a Jacobian matrix. Then, the aerodynamics of the proposed aerial robotic camera was analyzed using ANSYS CFX, a commercial computational fluid dynamics software. The air drag force affected the dynamics of the aerial robotic camera significantly under various conditions. And then, workspace analysis was performed to determine the available working range. The workspace became smaller when force and rotational moments increased.
Similar content being viewed by others
References
Arsenault M (2013) Workspace and stiffness analysis of a three-degree-of-freedom spatial cable-suspended parallel mechanism while considering cable mass. Mech Mach Theory 66:1–13
Barrette G, Gosselin CM (2005) Determination of the dynamic workspace of cable-driven planar parallel mechanisms. Trans ASME 127:242–248
Behzadipour S, Dekker R, Khajepour A, Chan E (2003) Deltabot: a new cable-based ultrahigh speed robot. In: ASME 2003 international mechanical engineering congress and exposition American Society of Mechanical Engineers, pp 533–537
Cetl V, Jurakić G, Mađer M, Tomić H, Kliment T (2016) Unmanned aircraft systems: successful usage limited by the regulation? New Technologies Engineering Geodesy and Multisensor Systems, pp 527–537
CFInFlight (2004) What is skycam. http://www.cfinflight.com/pages/skycam.asp
Chaube A, Sahoo PK, Solanki SC (2006) Analysis of heat transfer augmentation and flow characteristics due to rib roughness over absorber plate of a solar air heater. Renew Energy 31:317–331
Filipovis M (2012) The importance of modelling an aerial robotic camera. Sci Tech Rev 62:28–37
Filipovis M, Djuric A (2016) Cable-suspended CPR-D type parallel robot. Theoret Appl Mech 54:645–657
Heo JM, Choi SH, Park KS (2016) Workspace analysis of a 6-DOF cable-driven parallel robot considering pulley bearing friction under ultra-high acceleration. Microsyst Technol. doi:10.1007/s00542-016-3025-x
Heyden T, Woernle C (2006) Dynamic and flatness-based control of a kinematically undetermined cable suspension manipulator. Multibody Syst Dyn 16:155–177
Kawamura S, Choe W, Tanaka S, Pandian SR (1995) Development of an ultrahigh speed robot FALCON using wire drive system. In: Robotics and automation, 1995. Proceedings, 1995 IEEE international conference on 1, pp 215–220
Kil SW, Humphrey JAC, Haj-Hariri H (2012) Numerical study of the flow-structure interactions in an air- or helium-filled simulated hard disk drive. Microsyst Technol 18:57–75
Morizono T, Kurahashi K, Kawamura S (1997) Realization of a virtual sports training system with parallel mechanism. In: IEEE International Conference 4, pp 3025–3030
Nan R (2006) Five hundred meter aperture spherical radio telescope (FAST). Sci China Ser 49:129–148
Pott A (2014) On the limitations in the lower and upper tensions for cable-driven parallel robots. Advances in Robot kinematics, pp 243–251
Pott A, Mütherich H, Kraus W, Schmidt V, Miermeister P, Verl A (2013) IPAnema : a family of cable-driven parallel robots for industrial applications. Mech Mach Sci 12:119–134
Riechel AT, Ebert-Uphoff I (2004) Force-feasible workspace analysis for underconstrained, point-mass cable robots. In: Robotics and automation, 2004. Proceedings. ICRA’04. 2004 IEEE International Conference on 5, pp 4956–4962
Schmidt V, Kraus W, Ho WY, Seon J, Pott A, Park JO, Verl A (2014) Extending Dynamic Trajectories of Cable-Driven Parallel Robots as a Novel Robotic Roller Coaster. Conference ISR ROBOTIK 2014, pp 368–373
Spidercam (2015) Spidercam SC250 Field Features and Specifications. http://www.spidercam.tv/products/sc250-field/, pp 1–2
Tadokoro S, Murao Y, Hiller M, Murata R, Kohkawa H, Matsushima T (2002) A motion base with 6-DOF by parallel cable drive architecture. IEEE/ASME Trans Mechatron 7:115–123
Wei H, Qiu Y, Yang J (2015) An approach to evaluate stability for cable-based parallel camera robots with hybrid tension-stiffness properties. Adv Robot Syst 12:1–12
Yuan H (2015) Static and dynamic stiffness analysis of cable-driven parallel. INSA de Rennes
Zubair M, Abdullah MZ, Ismail R, Shuaib IL, Hamid SA, Ahmad KA (2011) Review: a critical overview of limitations of CFD modeling in nasal airflow. Med Biol Eng 32:77–84
Acknowledgement
This research was supported by Leading Foreign Research Institute Recruitment Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Science, ICT & Future Planning (MSIF) (2012K1A4A3026740).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Do, HD., Seo, JH., Park, JO. et al. Wrench-feasible workspace analysis considering aerodynamics of aerial robotic camera under high speed. Microsyst Technol 23, 5257–5269 (2017). https://doi.org/10.1007/s00542-016-3245-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00542-016-3245-0