Abstract
In this work we have revisited the problem of molding a deformable substrate with a rigid flat punch. The work is motivated by the recent experiments by Chen et al. (Acta Mater 59:1112−1120, 2011) where it was shown that systematically determined characteristic molding pressure H increased significantly with decrease in punch width, for widths less than \(\sim 25 \; \mu m\). This size effect, akin to the indentation size effect observed in nano-indentation of metals, assumes importance in applications involving molding of metallic microstructures. Numerical simulations have been conducted within the framework of a finite deformation higher order strain gradient model. While classical plasticity predicts almost uniform stress with severe plastic strain concentration at the sharp corners to prevail just beneath the punch, our simulations present a significantly different picture. Very narrow punches have fairly uniform plastic strain with severe concentration of strain gradients and large contact stresses close to the edges. Wider punches however, behave in a manner closely resembling the predictions of classical plasticity.
Similar content being viewed by others
References
Chen K, Meng WJ, Mei F, Hiller J, Miller DJ (2011) From micro- to nano-scale molding of metals: size effect during molding of single crystal al with rectangular strip punches. Acta Mater 59:1112–1120. doi:10.1016/j.actamat.2010.10.044
Hill R (1950) The mathematical theory of plasticity. Oxford University Press, Oxford
Nepershin RI (2002) Indentation of a flat punch into a rigid-plastic half space. J Appl Math Mech 66:135–140
Lee CH, Kobayashi S (1970) Elastoplastic analysis of plane-strain and axisymmetric flat punch indentation by the finite-element method. Int J Mech Sci 12:349–370
Murthy TG, Huang C, Chandrasekar S (2008) Characterization of deformation field in plane-strain indentation of metals. J Phys D Appl Phys:41
Cao DM, Guidry D, Meng WJ, Kelly KW (2003) Molding of pb and zn with microscale mold inserts. Microsyst Technol 9:559–566
Cao DM, Meng WJ (2004) Microscale compression molding of al with surface engineered liga inserts. Microsyst Technol 10:662–670
Jiang J, Mei F, Meng WJ (2008) Fabrication of metal-based high-aspect-ratio microscale structures by compression molding. J Vac Sci Technol A 26:745–751
Madou MJ (1997) Fundamentals of microfabrication. CRC Press
Cross GLW, O’Connell BS, Pethica JB, Rowland H, King WP (2008) Variable temperature thin film indentation with a flat punch. Rev Sci Instrum 79(1):013904. doi:10.1063/1.2830028
Nix WD, Gao H (1998) Indentation size effects in crystalline materials: a law for strain gradient plasticity. J Mech Phys Solids 46:411–425
Fleck NA, Hutchinson JW (1997) Strain gradient plasticity. Adv Appl Mech 33:295–361
Fleck NA, Hutchinson JW (2001) A reformulation of strain gradient plasticity. J Mech Phys Solids 49(10):2245–2271. doi:10.1016/S0022-5096(01)00049-7
Swadener JG, George EP, Pharr GM (2002) The correlation of the indentation size effects measured with indenters of various shapes. J Mech Phys Solids 50:681–694
Aifantis EC (1984) On the microstructural origin of certain inelastic models. J Eng Mater 106:326–330
Stölken JS, Evans AG (1998) A microbend test method for measuring the plasticity length scale. Acta Mater 46:5109–5115
Fleck NA, Muller GM, Ashby MF, Hutchinson JW (1994) Strain gradient plasticity: theory and experiment. Acta Metall Mater 42:475–487
Borg U, Niordson CF, Fleck NA, Tvergaard V (2006) A viscoplastic strain gradient analysis of materials with voids or inclusions. Int J Solids Struct 43:4906–4916
Niordson CF, Redanz P (2004) Size-effects in plane strain sheet-necking. J Mech Phys Solids 52:2431–2454
De Borst R, Pamin J (1996) Some novel developments in finite element procedures for gradient-dependent plasticity. Int J Numer Methods Eng 39:2477–2505
Mikkelsen LP, Goutianos S (2009) Suppressed plastic deformation at blunt crack-tips due to strain gradient effects. Int J Solids Struct 46:4430–4436
Evans AG, Hutchinson JW (2009) A critical assessment of theories of strain gradient plasticity. Acta Mater 57:1675–1688
Tan T-M, Li S, Chou PC (1990) Finite element solution of prandtl’s flat punch problem. Exp Syst Appl 1(1):173–186. ISSN 0957-4174
Riccardi B, Montanari R (2004) Indentation of metals by a flat-ended cylindrical punch. Mater Sci Eng A-Struct 381:281–291
Acknowledgments
The authors gratefully acknowledge the financial support from the Department of Science and Technology, Govt. of India for the present work.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Guha, S., Sangal, S. & Basu, S. Numerical investigations of flat punch molding using a higher order strain gradient plasticity theory. Int J Mater Form 7, 459–467 (2014). https://doi.org/10.1007/s12289-013-1141-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12289-013-1141-z